46252638 supply of anvil suitable & collet suitable for orione makeanvil suitable & collet suitable for orione make,anvil suitable for orione make 7/8 inch nose assembly : ohpl i 2228 n1 orione make: orion e or equivalent . [ warranty period: 30 months after the date of delivery ] ] , collet suitable for orione make 7/8 inch nose assembly : ohpl i 2228 n1 make: orione or eq uivalent. [ warranty period: 30 months after the date of delivery ] ]...
46217440 the directorate of employment & training (training wing), labour resources department, govt. of bihar (the tendering authority) invites e tenders from registered indian manufacturers/oem/oem authorised distributers/dealers for supply, installation and commissioning (with amc as applicable) of machines/tools/ equipment as per the specified requirements and technical specifications, grouped under schedule i & ii of this rfq at various govt. itis in bihar.1 c : machineries and equipments lathe s.s. & s.c. (all geared head stock) with minimum specification as:(with d.r.o. z & y axis) 2 c : machineries and equipments lathe s.s & s.c.(all geared type) with minimum specification as: 3 c : machineries and equipments lathe tool room s.s. & s.c. (all geared type) with minimum specification as (with d.r.o. z & y axis) 4 c : machineries and equipments grinding machine pedestal type 5 c : machineries and equipments drill machine pillar type motorized 6 c : machineries and equipments power saw machine – hydraulic feedsystem 7 c. general installation/ machineries discrete component trainer / basic electronics trainer 8 c. general installation/ machineries drilling machine bench to drill up to 12mm dia. along with accessories 9 c. general installation/ machineries grinding machine (general purpose) d.e. pedestal with 300 mm dia. wheels rough and smooth 10 c. general installation/ machineries tractor diesel engine 4 stroke for dismantling and assembling with 11 c. general installation/ machineries welding plant oxy acetylene complete ( high pressure) 12 c. general installation/ machineries wheel type tractor fitted with diesel engine with standardaccessories 13 c. general installation/machineries tractor 14 c. general installation/machineries tractor 15 c. general machinery universal testing machine for plastic 16 c. general machinery plastic scrap grinder 17 c. general machinery pre heater 18 c. general machinery automatic screw type injection moulding machine 19 c. general machinery hand operated compression mouldingmachine 20 c. general machinery automatic compression moulding machine 21 c. general machinery hand operated blow moulding machine 22 c. general machinery automatic extrusion blow moulding machine 23 c. general machinery extruder of 40 kg/hr. plasticizing capacity 24 c. general machinery pipe extruder of 40 kg/hr. plasticizingcapacity 25 c. general machinery extruderof40 kg/hr. plasticizing capacity 26 c. general machinery thermo/vacuum forming machine with mould 27 c. general machinery rotational moulding machine with mould 28 c. general machinery hydraulic trainer kit 29 c. general machinery pneumatic trainer kit 30 c. general machinery programmable logic control 31 c. general machinery strech blow moulding machine 1 literwith mould 32 c. general machinery air compressor with air treatment accessories 5 hp 33 c. general machinery shop outfit air compressor with maximum working pressure 34 c. general machinery shop outfit moulding sand muller 35 c. general machinery shop outfit co2 cylinder with co2 probe and rubber hoses 36 c. general machinery shop outfit heating and pumping unit to suit to oil fired tilting type crucible furnace with heating pressure gauge etc.motorized rotary gear oil pump pre heater. 37 c. general machinery shop outfit sand testing equipment permeability meter, universal strength tester, sieve shaker, standard sand rammer, shatter index tester, clay content tester,speedy moisture teller. 38 c. general machinery shop outfit moulding machine hand squeeze with stripping device pin lift type. 39 c. general machinery shop outfit weighing machine 40 c. general machinery shop outfit pedestal grinder de operated 41 c. general machinery shop outfit core oven 42 c. general machinery shop outfit muffle furnace (electric) 43 c. general machinery shop outfit auto sand riddle 44 c. general machinery shop outfit one man ladle 45 c. general machinery shop outfit two man ladle 46 c. general machinery shop outfit oil fired tilting type crucible furnace 47 c. general machinery shop outfit pit furnace 48 c. general machinery shop outfit gravity die casting machine 49 c. general machinery shop outfit usg testing machine 50 c. general machinery shop outfit magnetic particle testing equipment 51 c. general machinery shop outfit induction furnace 52 d. mechatronics lab outfit simple servomotor trainer kit. 53 d. mechatronics lab outfit simple stepper motor trainer kit. 54 d. mechatronics lab outfit application trainer kit of proximity sensor, float switch, and reed switch 55 d. mechatronics lab outfit electro pneumatic control trainer kit using plc with required components. 56 d. mechatronics lab outfit electro hydraulic control trainer kit using plc with required components. 57 d. mechatronics lab outfit linear scale setup for positional accuracy check 58 d. mechatronics lab outfit plc based conveyor system with pick and place and sorting of objects (pneumatic andhydraulic)) 59 d. mechatronics lab outfit cut section models of pneumatic and hydraulic motors ,pumps 60 e. general machinery installation d.e. pedestal grinding machine withwheels rough and smooth 61 e. general shop outfit sensitive drilling machine 62 e. general shop outfit shearing machine (lever type) hand operated complete 63 e. general shop outfit hydraulic surface grinding machine 64 e. general shop outfit universal cylindrical grinding machine 65 f. general machinery shop outfit slotter 66 f. general machinery shop outfit ss and sc centre lathe (all geared) with specification as: 67 f. general machinery shop outfit tool and cutter grinder 68 f. general machinery shop outfit drilling machine pillar 69 f. general machinery shop outfit radial drill 70 f. general machinery shop outfit double ended pedestal grinder 71 f. general machinery shop outfit universal milling machine with minimum specification as: 72 f. general machinery shop outfit horizontal milling machine with minimum specification as: 73 f. general machinery shop outfit vertical milling machine with minimum specification as: 74 f. general machinery shop outfit surface grinding machine with minimum specification as: 75 f. general machinery shop outfit cylindrical grinder 76 f. general machinery shop outfit cnc lathe/cnc turn centre 77 f. general machinery shop outfit cnc vertical machining centre 78 f. general machinery shop outfit cnc milling tools 79 f. general machinery shop outfit cnc hole machining tools 80 general shop outfit welding transformer 81 general shop outfit welding transformer (or) inverter based welding machine (igbt) 82 general shop outfit d.c arc welding rectifiers set with all accessories 83 general shop outfit gmaw welding machine 84 general shop outfit ac/dc gtaw welding machine 85 general shop outfit air plasma cutting equipment 86 general shop outfit air compressor suitable for above air plasma cutting system. 87 general shop outfit spot welding machine 88 general shop outfit portable gas cutting machine (pug) 89 general shop outfit pedestal grinder fitted with coarse and medium grain size grindingwheels 90 general shop outfit bench grinder fitted with fine grain size silicon carbide green grindingwheel 91 general shop outfit hand shearing machine capacity 92 general shop outfit power saw machine 93 general shop outfit portable drilling machine 94 general shop outfit oven, electrode drying 95 general shop outfit welding simulators for smaw/gtaw/gmaw 96 general shop outfit water cooled induction welding/ brazing machine 97 general shop outfit plastic welding machine with hot air gun 98 general shop outfit swaging and flooring tool kit 450tubing 99 general shop outfit air conditioned crdi vehicle in running condition lmv 100 general shop outfit arbor press hand operated 2 ton capacity 101 general shop outfit automotive diesel smokemeter (for diesel engine) 102 general shop outfit bench lever shears 103 general shop outfit dual magnetization yoke 104 general shop outfit heavy commercial vehicle type (withoutbody on frame) 105 general shop outfit hydraulic jack hi lift type 3 ton capacity, and 5 ton capacity 106 general shop outfit liquid penetrate inspection kit 107 general shop outfit pipe bending machine (hydraulic type) 108 general shop outfit pneumatic rivet gun with standard accessories 109 general shop outfit tin smiths bench folder 110 general shop outfit trolley type portable air 111 general shop outfit welding plant oxy acetylene complete ( high pressure) 112 general shop outfit welding transformer with all accessoriesincluding consumables 113 general shop outfit diesel engine six cylinder in running condition 114 general shop outfit diesel engine – crdi 4 strokefor dismantling and assembling with swiveling stand. 115 general shop outfit diesel engine (running condition) stationary type single cylinder 116 general shop outfit hydraulic jack hi lift type 117 general shop outfit multi scan tool to scan engine,abs & ebd, at, srs, body control and immobilizer 118 general shop outfit spring tension tester 119 general shop outfit working condition of diesel engine – crdi 4 stroke engine, assembly with fault simulation board 120 general shop outfit cut section of 4/6 cylinder dieselengine in moving condition to show movement of internal parts 121 general shop outfit diesel engine six cylinder in running condition 122 general shop outfit air bag simulator 123 general shop outfit air conditioning service unit (car) 124 general shop outfit four stroke petrol engine with cng setup working condition 125 general shop outfit heavy commercial vehicle 126 general shop outfit mpfi petrol engine with swiveling stand along with special tools for dismantling and assembling 127 general shop outfit petrol engine(2 stroke) motor cycle/scooter along with special tools and accessories (optional)* if not available in market videodemonstration may be used to explain working. 128 general shop outfit transfer case with stand fordismantling and assembly. 129 general shop outfit tube/ tyre vulcanizing machine 130 general shop outfit two post car lift – capacity 4000kg 131 general shop outfit tyre changer machine 132 general shop outfit ultrasonic injection cleaning equipment 133 general shop outfit wheel alignment machine –computerized 3d (optional) 134 general shop outfit wheel balancing machine 135 general shop outfit working condition of petrol mpfi engine assembly with fault simulation board 136 general shop outfit working condition of e.v(electric vehicle ) car 137 b. instruments and general shop outfit steel rule graduated both in metric andenglish unit 138 b. instruments and general shop outfit straight edge steel 139 b. instruments and general shop outfit spirit level metal type 2 140 b. instruments and general shop outfit stud extractor ezy out 141 b. instruments and general shop outfit micrometer inside with extension rods. 142 b. instruments and general shop outfit vernier caliper 143 b. instruments and general shop outfit vernier height gauges 144 b. instruments and general shop outfit vernier bevel protractor blade withacute angle attachment 145 b. instruments and general shop outfit screw pitch gauge metric 146 b. instruments and general shop outfit wire gauge, metric standard. 147 c. tools for allied trade trammel 148 c. tools for allied trade pocker 149 c. tools for allied trade prick punch 150 c. tools for allied trade mallet. 151 c. tools for allied trade aviation snips straight cut 152 c. tools for allied trade flat headed hammers with handle. 153 c. tools for allied trade planishing hammer. 154 c. tools for allied trade snip bent left cut 155 c. tools for allied trade stake hatchet with leg. 156 c. tools for allied trade stake grooving. 157 d. modified list of tools for the 2nd year for fitter trade slip gauge as johnson metric set. 158 d. modified list of tools for the 2nd year for fitter trade gauge snap go and not go 159 d. modified list of tools for the 2nd year for fitter trade gauge plug 160 d. modified list of tools for the 2nd year for fitter trade gauge telescopic set. 161 d. modified list of tools for the 2nd year for fitter trade dial test indicator on stand 162 d. modified list of tools for the 2nd year for fitter trade sine bar 163 d. modified list of tools for the 2nd year for fitter trade dial vernier caliper. (universal type) 164 d. modified list of tools for the 2nd year for fitter trade screw thread micrometer withinterchangeable. pitch anvils for checking metric threads 60. 165 d. modified list of tools for the 2nd year for fitter trade depth micrometer. 0 25 mm 166 d. modified list of tools for the 2nd year for fitter trade digital vernier caliper. 167 d. modified list of tools for the 2nd year for fitter trade digital micrometer outside. 168 d. modified list of tools for the 2nd year for fitter trade comparators gauge dial indication withstand and bracket. 169 d. modified list of tools for the 2nd year for fitter trade engineers try square (knife edge) 170 d. modified list of tools for the 2nd year for fitter trade surface roughness comparison plates 171 d. modified list of tools for the 2nd year for fitter trade digital vernier caliper 172 d. modified list of tools for the 2nd year for fitter trade vernier bevel protector 173 b. instruments and general shop outfit adjustable spanner (pipe wrench) 174 b. instruments and general shop outfit ac alternator slip ring puller 175 b. instruments and general shop outfit air blow gun with standardaccessories 176 b. instruments and general shop outfit air ratchet 177 b. instruments and general shop outfit air impact wrench 178 b. instruments and general shop outfit auto electrical test bench 179 b. instruments and general shop outfit battery –charger 180 b. instruments and general shop outfit blow lamp 181 b. instruments and general shop outfit belt tensioner gauge 182 b. instruments and general shop outfit car jet washer with standard accessories 183 b. instruments and general shop outfit chain pulley block capacity withtripod stand 184 b. instruments and general shop outfit chisel flat 185 b. instruments and general shop outfit circlip pliers expanding andcontracting 186 b. instruments and general shop outfit cleaning tray 187 b. instruments and general shop outfit compression testing gauge 188 b. instruments and general shop outfit cylinder bore gauge capacity 189 b. instruments and general shop outfit depth micrometer 190 b. instruments and general shop outfit dial gauge type 1 gr. a (complete with clamping devices and withmagnetic stand) 191 b. instruments and general shop outfit different type of engine bearingmodel 192 b. instruments and general shop outfit different type of piston model 193 b. instruments and general shop outfit engineers stethoscope 194 b. instruments and general shop outfit files assorted sizes and typesincluding safe edge file (20 no’s) 195 b. instruments and general shop outfit fuel feed pump for diesel 196 b. instruments and general shop outfit fuel injection pump (diesel)inline 197 b. instruments and general shop outfit fuel injection pump ve pump / distributor fuel rotary pump (dpc) pumps / along with specialtools and accessories 198 b. instruments and general shop outfit grease gun 199 b. instruments and general shop outfit grease gun heavy duty trolleytype 200 b. instruments and general shop outfit growler 201 b. instruments and general shop outfit hand operated crimpingtool/wire 202 b. instruments and general shop outfit injector – multi hole type, pintletype 203 b. instruments and general shop outfit injector testing set 204 b. instruments and general shop outfit magneto spanner set with 8spanners 205 b. instruments and general shop outfit automotive oil pump fordismantling and assembling. 206 b. instruments and general shop outfit philips screw driver set of 5pieces (pozidrivandtorx drive) 207 b. instruments and general shop outfit piston ring expander andremover. 208 b. instruments and general shop outfit scriber with scribing blackuniversal 209 b. instruments and general shop outfit spanner t. flocks for screwing upand up screwing inaccessible 210 b. instruments and general shop outfit spark plug spanner 14mm x18mm x size 211 b. instruments and general shop outfit starter motor axial type, pre engagement type & co axial type 212 b. instruments and general shop outfit surface gauge with dial testindicator plunger type 213 b. instruments and general shop outfit tyre pressure gauge with holdingnipple 214 b. instruments and general shop outfit universal puller for removingpulleys, bearings 215 b. instruments and general shop outfit v’ block 75 x 38 mm pair withclamps 216 b. instruments and general shop outfit valve spring compressoruniversal 217 b. instruments and general shop outfit automotive water pump fordismantling and assembling 218 b. instruments and general shop outfit working model of air brake assembly 219 b. instruments and general shop outfit alternator assembly used forlmv 220 b. instruments and general shop outfit carburetor – solex, mikuny fordismantling and assembling 221 b. instruments and general shop outfit chain pulley block 3 ton capacitywith tripod stand 222 b. instruments and general shop outfit cut section model of mock layout of a motor car –electrical system working model 223 b. instruments and general shop outfit cut section models of shockabsorbers 224 b. instruments and general shop outfit cut section of cross ply and radialtyres 225 b. instruments and general shop outfit cut section working model of automatic transmission gear box 226 b. instruments and general shop outfit cut section working model ofcentrifugal clutch assembly. 227 b. instruments and general shop outfit cut section working model ofdiaphragm clutch assembly. 228 b. instruments and general shop outfit cut section working model ofsingle plate clutch assembly 229 b. instruments and general shop outfit demonstration board of electronic ignition system,ignition coil 230 b. instruments and general shop outfit demonstration board of mpfi system 231 b. instruments and general shop outfit disk brake in working condition with caliper assembly with allparts 232 b. instruments and general shop outfit drum brake assembly in workingcondition 233 b. instruments and general shop outfit front axle (rzeeppa joint) withstand for dismantling and assembly 234 b. instruments and general shop outfit full floating axle and semi floating axle assembly 235 b. instruments and general shop outfit functional/experiment model of different type of sensors. 236 b. instruments and general shop outfit steering assembly –1.rack & pinion 2.worm & roller3. recirculating ball 4.power steering5. electric assisted power steering 237 b. instruments and general shop outfit synchronous gear box with standfor dismantling and assembly 238 b. instruments and general shop outfit tandem master cylinder withbooster 239 b. instruments and general shop outfit working model of power windows 240 b. instruments and general shop outfit working model of torqueconverter 241 tools & equipments for engineering drawing hall mini drafter 242 tools & equipments for engineering drawing hall set square 243 b. shop tools, instruments neon (phase) tester 244 b. shop tools, instruments electric soldering iron 245 b. shop tools, instruments tube cutter 246 b. shop tools, instruments allen keyset(metric) 247 b. shop tools, instruments allen keyset(english 248 b. shop tools, instruments soldering station(temp. controlled)with necessary accessories 249 b. shop tools, instruments philips screwdriver 250 b. shop tools, instruments round nose pliers 251 d. rotational/velocity instruments digital type tachometer 252 e. precision instruments digital panel meters voltage & current 253 e. precision instruments d.c. regulated power supply 254 e. precision instruments digital insulation tester 255 e. precision instruments digital multimeter51/2 digit bench top digital multimeter 256 e. precision instruments digital l.c.r. bridge 257 e. precision instruments operational amplifier trainer 258 e. precision instruments trainer on basic digital electronicsi.e. logic gates boolean expression adder, sub tractor, flip flop, counter register, converter etc. 259 e. precision instruments trainers on power suppliers half wave rectifier, full wave rectifier 260 e. precision instruments discrete component trainer with following seven basic modules diode characteristics (si, zener, led) rectifier circuit diode as clipper circuit diode as clamping circuit zener as voltage regulator. transistor type npn & pnp and ce characteristics transistor as a switch 261 g. electrical instruments autotransformer1øand3ø 262 g. electrical instruments calibration test bench for ac and dc voltmeter, ac and dc ammeter, ohmmeter 263 h. pressure instruments u tube manometers 264 h. pressure instruments well type manometer 265 h. pressure instruments inclined limb manometers 266 h. pressure instruments bourdon tube type gauges ofvarious ranges 267 h. pressure instruments capsule type pressure gauges 268 h. pressure instruments dead weight tester & comparator 269 h. pressure instruments pressure regulators with filter and input & output gauges 270 h. pressure instruments differential pressuretransmitter 271 h. pressure instruments differential pressure transmitter (electronic hart/field bus type) 272 h. pressure instruments sensor trainer kit containing following sensorsrtd,ntc thermistor,lm35 , thermocouple j ,k type and ad590 photovoltaic, photoconductive , phototransistor and photodiode air humidity and temperature 273 h. pressure instruments diaphragm type pressure gauges of various ranges 274 h. pressure instruments pressure transducers training kits potentiometercapacitive reluctive strain gauge lvdtload cell servo typepiezo resistive 275 h. pressure instruments experimental setup for pressure measurement consisting of air compressor pressure vessel pressure transmitter controller recorder and final control element, computeri.e. closed loop system or full scope system i.e. pressure instrumentation process controltrainer/simulator 276 h. pressure instruments hart device communicator and calibrator 277 h. pressure instruments pneumatic calibrator 278 h. pressure instruments pressure switches of various ranges 279 h. pressure instruments p to i and i to p converters training platform 280 h. pressure instruments vacuum tester with pump 281 i. flowmeters/ instruments simple tank type quantity meter 282 i. flowmeters/ instruments impeller type flow meter 283 i. flowmeters/ instruments helical and turbine flow meter 284 level control set up with level transmitters controller & control valve complete experimental setup or level simulator 285 o. equipment for microprocessors microcontroller development platform 286 b. tools, measuring instruments and general shop outfit calipers, vernier(digital) 287 b. tools, measuring instruments and general shop outfit height gauge 288 b. tools, measuring instruments and general shop outfit diamond, wheel dressing 289 b. tools, measuring instruments and general shop outfit techometer(digital) 290 b. tools, measuring instruments and general shop outfit demagnetizer chuck 291 b. tools, measuring instruments and general shop outfit static balancing stand for grinding wheel 292 b. tools, measuring instruments and general shop outfit dial test indicator(digital) 293 b. instruments and general shop outfit surface plate 294 b. instruments and general shop outfit marking off table 295 b. instruments and general shop outfit scribing block universal 296 b. instruments and general shop outfit v block 297 b. instruments and general shop outfit try square 298 b. instruments and general shop outfit outside spring caliper 299 b. instruments and general shop outfit divider spring 300 b. instruments and general shop outfit inside spring caliper 301 b. instruments and general shop outfit straight edge steel 302 b. instruments and general shop outfit straight edge steel 303 b. instruments and general shop outfit steel tape 304 b. instruments and general shop outfit steel rule 305 b. instruments and general shop outfit sprit level 306 b. instruments and general shop outfit hammer 307 b. instruments and general shop outfit screw driver, heavy duty 308 b. instruments and general shop outfit hammer lead 309 b. instruments and general shop outfit spindle blade screw driver 310 b. instruments and general shop outfit allen hexagonal keys 311 b. instruments and general shop outfit spanner d.e. 312 b. instruments and general shop outfit adjustable spanner 313 b. instruments and general shop outfit reduction sleeve morse 314 b. instruments and general shop outfit angle plate size 315 b. instruments and general shop outfit solid parallels in pairs (different sizes) in metric 316 b. instruments and general shop outfit oil can pressure feed 317 b. instruments and general shop outfit oil stone 318 b. instruments and general shop outfit number drills h.s.s. (parallel shank) 319 b. instruments and general shop outfit punch letter . 320 b. instruments and general shop outfit punch number 321 b. instruments and general shop outfit twist drills 322 b. instruments and general shop outfit drill chuck 323 b. instruments and general shop outfit centre drill 324 b. instruments and general shop outfit grinding wheel dresser (diamond) 325 b. instruments and general shop outfit grinding wheel dresser huntington type 326 b. instruments and general shop outfit tap and die in box metric pitch 327 b. instruments and general shop outfit drill h.s.s. taper shank 328 b. instruments and general shop outfit file half round 329 b. instruments and general shop outfit file triangular smooth 330 b. instruments and general shop outfit needle file 331 b. instruments and general shop outfit file square 332 b. instruments and general shop outfit reamer 333 b. instruments and general shop outfit reamer adjustable 334 b. instruments and general shop outfit tool bits 335 b. instruments and general shop outfit tool bits 336 b. instruments and general shop outfit tool bits holder (armstrong) l.h 337 b. instruments and general shop outfit tool bits holder (armstrong) r.h. 338 b. instruments and general shop outfit assorted tools and bit holders for lathe, shaper, slotter& planner in different shapes and sizes 339 b. instruments and general shop outfit hacksaw frame adjustable 340 b. instruments and general shop outfit table chuck 341 b. instruments and general shop outfit bench vice 342 b. instruments and general shop outfit machine vice 343 b. instruments and general shop outfit machine vice 344 b. instruments and general shop outfit hand vice 345 b. instruments and general shop outfit radius turning attachment 346 b. instruments and general shop outfit angle turning attachment 347 b. instruments and general shop outfit compound angle vice (standard sine) 348 b. instruments and general shop outfit universal machine vice 349 b. instruments and general shop outfit universal table angle plate 350 b. instruments and general shop outfit shaper tool holder turret type to suit the machine 351 b. instruments and general shop outfit base chuck for slotter to suit the machine 352 b. instruments and general shop outfit shaper indexing center to suit the machine 353 b. instruments and general shop outfit knurling tools 354 b. instruments and general shop outfit plier cutting 355 b. instruments and general shop outfit carbide tipped tools of different sizes and shapes (throw away tips) 356 b. instruments and general shop outfit hand hammer 357 c. milling cutters milling cutter cylindrical cutter 358 c. milling cutters milling cutter cylindrical cutter 359 c. milling cutters milling cutter 360 c. milling cutters milling cutter 361 c. milling cutters milling cutter 362 c. milling cutters milling cutter 363 c. milling cutters milling cutter side and face cutter 364 c. milling cutters milling cutter side and face cutter 365 c. milling cutters milling cutter equal angle cutter 366 c. milling cutters milling cutter equal angle cutter 367 c. milling cutters milling cutter equal angle cutter 368 c. milling cutters milling cutter double angle unequal 369 c. milling cutters milling cutter double angle unequal 370 c. milling cutters milling cutter double angle unequal 371 c. milling cutters milling cutter double angle unequal 372 c. milling cutters milling cutter single angle 373 c. milling cutters milling cutter single angle 374 c. milling cutters milling cutter single angle 375 c. milling cutters milling cutter single angle 376 c. milling cutters milling cutter slitting saw cutter 377 c. milling cutters milling cutter slitting saw cutter 378 c. milling cutters milling cutter shell end mill 379 c. milling cutters milling cutter shell end mill 380 c. milling cutters milling cutter parallel shank end mills 381 c. milling cutters milling cutter t slot cutter with parallel shank 382 c. milling cutters milling cutter concave 383 c. milling cutters milling cutter convex 384 c. milling cutters involute gear cutter 385 d. measuring instruments micrometer outside 386 d. measuring instruments micrometer outside 387 d. measuring instruments micrometer outside 388 d. measuring instruments micrometer outside 389 d. measuring instruments micrometer depth gauge 390 d. measuring instruments digital micrometer 391 d. measuring instruments vernier caliper 392 d. measuring instruments direct reading vernier caliper 393 d. measuring instruments digital vernier caliper 394 d. measuring instruments vernier height gauge q 395 d. measuring instruments vernier gear tooth caliper 396 d. measuring instruments combination 397 d. measuring instruments vernier bevel protractor 398 d. measuring instruments bevel gauge 399 d. measuring instruments telescopic gauge 400 d. measuring instruments sine bar 401 d. measuring instruments universal dial test indicator 402 d. measuring instruments centre gauge com. 403 d. measuring instruments gauge slip box 404 d. measuring instruments gauge screw pitch 405 d. measuring instruments gauge radius 406 d. measuring instruments limit plug gauges 407 d. measuring instruments ring gauges 408 d. measuring instruments taper gauge 409 d. measuring instruments gauge feeler / thickness 410 b. instruments and general shop outfit air blow gun with standard accessories 411 b. instruments and general shop outfit ammeter dc with external shunt 412 b. instruments and general shop outfit air ratchet with standard accessories 413 b. instruments and general shop outfit air impact wrench with standard accessories 414 b. instruments and general shop outfit anvil with stand 415 b. instruments and general shop outfit calliper inside with spring 416 b. instruments and general shop outfit callipers outside with spring 417 b. instruments and general shop outfit chain pulley block capacity with tripod stand 418 b. instruments and general shop outfit chisels cross cut 419 b. instruments and general shop outfit circlip pliers expanding and contracting 420 b. instruments and general shop outfit compression testing gauge suitable for diesel engine with standard accessories 421 b. instruments and general shop outfit connecting rod alignment fixture 422 b. instruments and general shop outfit copper bit soldering iron 423 b. instruments and general shop outfit cylinder liner dry & wet liner, press fit &slidefit liner 424 b. instruments and general shop outfit dc ohmmeter 425 b. instruments and general shop outfit dial gauge type 1 gr. a (complete with clamping devices and with magnetic stand) 426 b. instruments and general shop outfit dividers with spring 427 b. instruments and general shop outfit drift punch copper 428 b. instruments and general shop outfit drill point angle gauge 429 b. instruments and general shop outfit drill twist (various sizes) 430 b. instruments and general shop outfit electric soldering iron 431 b. instruments and general shop outfit electric testing screw driver 432 b. instruments and general shop outfit engineer’s square 433 b. instruments and general shop outfit feeler gauge 20 blades (metric) 434 b. instruments and general shop outfit file flat , bastard 435 b. instruments and general shop outfit file, half round ,second cut 436 b. instruments and general shop outfit file, square second cut 437 b. instruments and general shop outfit file, square round 438 b. instruments and general shop outfit file, triangular , second cut 439 b. instruments and general shop outfit flat file , second cut 440 b. instruments and general shop outfit flat file , bastard 441 b. instruments and general shop outfit fuel injection pump (diesel) inline 442 b. instruments and general shop outfit fuel injection pump dismantling tool kit/universal vice 443 b. instruments and general shop outfit fuel injection pump ve pump / distributor fuel rotary pump (dpc) pumps / along with special tools and accessories 444 b. instruments and general shop outfit gloves for welding 445 b. instruments and general shop outfit glow plug tester 446 b. instruments and general shop outfit granite surface plate with stand and cover 447 b. instruments and general shop outfit grease gun heavy duty trolley type 448 b. instruments and general shop outfit hammer chipping 449 b. instruments and general shop outfit hammer copper with handle 450 b. instruments and general shop outfit hand operated crimping tool 451 b. instruments and general shop outfit hand reamers adjustable 452 b. instruments and general shop outfit hand shear universal 453 b. instruments and general shop outfit hand vice 454 b. instruments and general shop outfit hollow punch set of seven pieces 455 b. instruments and general shop outfit injector – multi hole type, pintle type 456 b. instruments and general shop outfit injector cleaning unit 457 b. instruments and general shop outfit injector testing set (hand tester) 458 b. instruments and general shop outfit insulated screw driver 459 b. instruments and general shop outfit insulated screw driver 460 b. instruments and general shop outfit left cut snips 461 b. instruments and general shop outfit lifting jack screw 462 b. instruments and general shop outfit magneto spanner set with 8 spanners 463 b. instruments and general shop outfit multimeter digital 464 b. instruments and general shop outfit oil can 465 b. instruments and general shop outfit oil pump for dismantling and assembling. 466 b. instruments and general shop outfit oil stone 467 b. instruments and general shop outfit oscilloscope 468 b. instruments and general shop outfit philips screw driver set of 5 pieces 469 b. instruments and general shop outfit pipe cutting tool 470 b. instruments and general shop outfit pipe flaring tool 471 b. instruments and general shop outfit piston ring compressor 472 b. instruments and general shop outfit piston ring expander and remover. 473 b. instruments and general shop outfit piston ring groove cleaner. 474 b. instruments and general shop outfit pliers combination 475 b. instruments and general shop outfit pliers flat nose 476 b. instruments and general shop outfit pliers round nose 477 b. instruments and general shop outfit pliers side cutting 478 b. instruments and general shop outfit portable electric drill machine 479 b. instruments and general shop outfit prick punch 480 b. instruments and general shop outfit radiator cut section cross flow 481 b. instruments and general shop outfit radiator cut section down flow 482 b. instruments and general shop outfit radiator pressure cap 483 b. instruments and general shop outfit right cut snips 484 b. instruments and general shop outfit rivet sets snap and dolly combined 485 b. instruments and general shop outfit scraper flat 486 b. instruments and general shop outfit scraper half round 487 b. instruments and general shop outfit scraper triangular 488 b. instruments and general shop outfit scriber 489 b. instruments and general shop outfit scriber with scribing black universal 490 b. instruments and general shop outfit set of stock and dies metric 491 b. instruments and general shop outfit tinnman’s shear 492 b. instruments and general shop outfit sheet metal gauge 493 b. instruments and general shop outfit tinnman’sshear 494 b. instruments and general shop outfit soldering copper 495 b. instruments and general shop outfit solid parallels in pairs (different size) in metric 496 b. instruments and general shop outfit spanner clyburn 497 b. instruments and general shop outfit spanner t. flocks for screwing up and up screwing inaccessible 498 b. instruments and general shop outfit spanner, adjustable 499 b. instruments and general shop outfit spanner, ring set of 12 metric sizes 500 b. instruments and general shop outfit spark lighter 501 b. instruments and general shop outfit spark plug spanner 14mm x 18mm x size 502 b. instruments and general shop outfit starter motor axial type, pre engagement type & co axial type 503 b. instruments and general shop outfit steel measuring tape in a case 504 b. instruments and general shop outfit steel rule 505 b. instruments and general shop outfit steel rule 30 cm inch and metric 506 b. instruments and general shop outfit straight edge gauge 2 ft. 507 b. instruments and general shop outfit straight edge gauge 4 ft. 508 b. instruments and general shop outfit stud extractor set of 3 509 b. instruments and general shop outfit stud remover with socket handle 510 b. instruments and general shop outfit surface gauge with dial test indicator plunger type 511 b. instruments and general shop outfit tachometer (counting type) 512 b. instruments and general shop outfit tandem master cylinder with booster 513 b. instruments and general shop outfit taps and dies complete sets (5 types) 514 b. instruments and general shop outfit taps and wrenches metric 515 b. instruments and general shop outfit telescope gauge 516 b. instruments and general shop outfit temperature gauge with sensor 517 b. instruments and general shop outfit thermostat 518 b. instruments and general shop outfit thread pitch gauge metric 519 b. instruments and general shop outfit timing lighter 520 b. instruments and general shop outfit torque wrenches 521 b. instruments and general shop outfit turbocharger cut sectional view 522 b. instruments and general shop outfit tyre pressure gauge with holding nipple 523 b. instruments and general shop outfit universal puller for removing pulleys, bearings 524 b. instruments and general shop outfit v’ block 75 x 38 mm pair with clamps 525 b. instruments and general shop outfit vacuum gauge 526 b. instruments and general shop outfit valve lifter 527 b. instruments and general shop outfit valve spring compressor universal 528 b. instruments and general shop outfit vernier calliper 529 b. instruments and general shop outfit vice grip pliers 530 b. instruments and general shop outfit water pump for dismantling and assembling 531 b. instruments and general shop outfit wire gauge (metric ) 532 b. tools, instruments and general shop outfit allen key set of 12 pieces 533 b. tools, instruments and general shop outfit alternator for tractor different type 534 b. tools, instruments and general shop outfit ammeter 535 b. tools, instruments and general shop outfit angle plate adjustable 536 b. tools, instruments and general shop outfit angle plate 537 b. tools, instruments and general shop outfit anvil 50 kgs with stand 538 b. tools, instruments and general shop outfit arbor press hand operated 539 b. tools, instruments and general shop outfit battery charger 540 b. tools, instruments and general shop outfit caliper inside 541 b. tools, instruments and general shop outfit calipers outside 542 b. tools, instruments and general shop outfit chain pulley block 3 ton capacity with tripod stand 543 b. tools, instruments and general shop outfit chaser hard w/v 9 to 40 t.p.i. set of 11 external. 544 b. tools, instruments and general shop outfit chaser, hand w/w 9 to 40 t.p.i. set of 11 internal 545 b. tools, instruments and general shop outfit chisel 546 b. tools, instruments and general shop outfit circlip pliers expanding and contracting type 547 b. tools, instruments and general shop outfit clamps c 548 b. tools, instruments and general shop outfit clamps c 549 b. tools, instruments and general shop outfit clamps c 550 b. tools, instruments and general shop outfit compression testing gauge suitable for diesel engine 551 b. tools, instruments and general shop outfit connecting rod alignment fixture 1 552 b. tools, instruments and general shop outfit cut section model of fuel filter 553 b. tools, instruments and general shop outfit cylinder liner dry & wet liner, press fit & slidefit liner 554 b. tools, instruments and general shop outfit dial gauge type 1 gr. a (completewith clamping devices and stand) 555 b. tools, instruments and general shop outfit different type of engine bearing model 556 b. tools, instruments and general shop outfit dividers 557 b. tools, instruments and general shop outfit drift, copper 558 b. tools, instruments and general shop outfit drill twist 559 b. tools, instruments and general shop outfit electric soldering 560 b. tools, instruments and general shop outfit engineers square 561 b. tools, instruments and general shop outfit feeler gauge 562 b. tools, instruments and general shop outfit file flat 563 b. tools, instruments and general shop outfit file, half round 564 b. tools, instruments and general shop outfit file, square 565 b. tools, instruments and general shop outfit file, square 566 b. tools, instruments and general shop outfit file, triangular 567 b. tools, instruments and general shop outfit files assorted sizes and types including safe edge file (20 nos) 568 b. tools, instruments and general shop outfit flat file 569 b. tools, instruments and general shop outfit granite surface plate 570 b. tools, instruments and general shop outfit grover 571 b. tools, instruments and general shop outfit hacksaw frame adjustable 572 b. tools, instruments and general shop outfit hammer ball peen 573 b. tools, instruments and general shop outfit hammer copper 574 b. tools, instruments and general shop outfit hand operated crimping tool (i) forcrimping up to 4mm and (ii) for crimping up to 10mm 575 b. tools, instruments and general shop outfit hydraulic jack hi lift type 576 b. tools, instruments and general shop outfit injector multi hole type, pintle type 577 b. tools, instruments and general shop outfit lifting jack screw type 578 b. tools, instruments and general shop outfit magneto spanner set with 579 b. tools, instruments and general shop outfit magnifying glass 580 b. tools, instruments and general shop outfit marking out table 581 b. tools, instruments and general shop outfit multi scan tool 582 b. tools, instruments and general shop outfit philips screwdriver set of 5 pieces 583 b. tools, instruments and general shop outfit portable oil monitoring indicator 584 b. tools, instruments and general shop outfit power supply 585 b. tools, instruments and general shop outfit punch letter 586 b. tools, instruments and general shop outfit rear axle assembly gear box steering box assembly of the diesel engine 587 b. tools, instruments and general shop outfit ridger. 588 b. tools, instruments and general shop outfit set of stock and dies unc, unfand metric 589 b. tools, instruments and general shop outfit soldering copper hatchet type 590 b. tools, instruments and general shop outfit spanner t. flocks for screwing up and up screwing inaccessible positions 591 b. tools, instruments and general shop outfit spanners socket with speed handle, t bar, ratchet and universal upto 32 mm set of 28pieces with box 592 b. tools, instruments and general shop outfit spirit level 593 b. tools, instruments and general shop outfit stake grooving. 594 b. tools, instruments and general shop outfit stake, hatchet. 595 b. tools, instruments and general shop outfit starter motor for tractor different type 596 b. tools, instruments and general shop outfit steel measuring tape 10 meter in a case 597 b. tools, instruments and general shop outfit steel rule 598 b. tools, instruments and general shop outfit steel wire brush 599 b. tools, instruments and general shop outfit stone, carborandum 600 b. tools, instruments and general shop outfit straight edge gauge 601 b. tools, instruments and general shop outfit straight edge gauge 602 b. tools, instruments and general shop outfit temperature gauge 603 b. tools, instruments and general shop outfit thread pitch gauge metric, bsw 604 b. tools, instruments and general shop outfit trammel 30 cm 605 b. tools, instruments and general shop outfit v block 606 b. tools, instruments and general shop outfit vacuum gauge to read 607 b. tools, instruments and general shop outfit valve spring compressor universal. 608 b. tools, instruments and general shop outfit voltmeter 609 b. tools, instruments and general shop outfit wing compass 610 b. instruments and general shop outfit surface plate granite 611 b. instruments and general shop outfit bench vice 612 b. instruments and general shop outfit v block 613 b. instruments and general shop outfit universal surface gauge 614 b. instruments and general shop outfit chisel cold flat 615 b. instruments and general shop outfit hammer copper/brass 616 b. instruments and general shop outfit hacksaw fixed 617 b. instruments and general shop outfit file flat 618 b. instruments and general shop outfit file flat 619 b. instruments and general shop outfit file flat 620 b. instruments and general shop outfit file half round 621 b. instruments and general shop outfit file round 622 b. instruments and general shop outfit file half round 623 b. instruments and general shop outfit knurling tool revolving head 624 b. instruments and general shop outfit combination set 625 b. instruments and general shop outfit screwdriver 626 b. instruments and general shop outfit spanner double ended 627 b. instruments and general shop outfit spanner adjustable 628 b. instruments and general shop outfit pliers flat nose 629 b. instruments and general shop outfit caliper transfer inside 630 b. instruments and general shop outfit micrometer inside 631 b. instruments and general shop outfit micrometer inside 632 b. instruments and general shop outfit depth gauge micrometer 633 b. instruments and general shop outfit vernier caliper outside, inside and depth 634 b. instruments and general shop outfit dial vernier caliper with metric 635 b. instruments and general shop outfit vernier bevel protractor 636 b. instruments and general shop outfit vernier micrometer 637 b. instruments and general shop outfit vernier micrometer 638 b. instruments and general shop outfit gauge feeler 639 b. instruments and general shop outfit gauge radius set 640 b. instruments and general shop outfit centre gauge 641 b. instruments and general shop outfit screw pitch gauge 642 b. instruments and general shop outfit drill angle gauge 643 b. instruments and general shop outfit universal dial test indicator plunger type 644 b. instruments and general shop outfit vernier height gauge 645 b. instruments and general shop outfit try square 646 b. instruments and general shop outfit plain ring and plug gauge 647 b. instruments and general shop outfit wheel dresser hunting on type withstar cutter 648 b. instruments and general shop outfit wheel dresser diamond 649 b. instruments and general shop outfit screw thread micrometerinterchangeable 650 b. instruments and general shop outfit morse taper plug & ring gauge 651 b. instruments and general shop outfit sine bar with centers 652 b. instruments and general shop outfit slip gauge metric set 653 b. instruments and general shop outfit morse taper 654 b. instruments and general shop outfit twist drill 655 b. instruments and general shop outfit drill twist set 656 b. instruments and general shop outfit drill chuck 657 b. instruments and general shop outfit tap & die 658 b. instruments and general shop outfit tap and die set 659 b. instruments and general shop outfit tap & die 660 b. instruments and general shop outfit tap & die 661 b. instruments and general shop outfit reamer machine 662 b. instruments and general shop outfit reamer adjustable 663 b. instruments and general shop outfit tool holder rh & straight for mmsquare tool bit 664 b. instruments and general shop outfit parting tool holder with h.s.s. blade 665 b. instruments and general shop outfit tool bits 666 b. instruments and general shop outfit boring tool holder 667 b. instruments and general shop outfit oil can 668 b. instruments and general shop outfit dog carrier 669 b. instruments and general shop outfit angle plate 670 b. instruments and general shop outfit combination drill / centre drill 671 b. instruments and general shop outfit oil stone 672 b. instruments and general shop outfit tap wrench (adjustable) 673 b. instruments and general shop outfit die and wrench 674 b. instruments and general shop outfit tool bit assorted sizes on holder 675 b. instruments and general shop outfit machine vice swivel base 676 b. instruments and general shop outfit spare grinding wheel ajax type forcarbide tool 677 b. instruments and general shop outfit angle gauge for tool grinding 678 b. instruments and general shop outfit hand chaser 679 b. instruments and general shop outfit hand chaser 680 b. instruments and general shop outfit revolving center (to suit lathetailstock) 681 b. instruments and general shop outfit tool cemented carbide assorted shaped(external) for steel turning 682 b. instruments and general shop outfit thread plug gauge 683 b. instruments and general shop outfit thread ring gauge 684 b. instruments and general shop outfit machine chaser 685 b. instruments and general shop outfit coventry die head 686 b. instruments and general shop outfit gauge drill grinding 687 b. instruments and general shop outfit magnetic chuck 688 b. instruments and general shop outfit lathe mandrels (diff. types) 689 b. instruments and general shop outfit coventry type die head (self opening) 690 b. instruments and general shop outfit collapsible tap with attachment 691 b. instruments and general shop outfit bore dial gauge stems 692 b. instruments and general shop outfit spindle key 693 b. instruments and general shop outfit screw driver 694 b. instruments and general shop outfit number punch 695 b. instruments and general shop outfit letter punch 696 b. instruments and general shop outfit magnifying glass 697 b. instruments and general shop outfit universal weld measuring gauge 698 b. instruments and general shop outfit spanner d.e. 699 b. instruments and general shop outfit c clamps 700 b. instruments and general shop outfit hammer sledge 701 b. instruments and general shop outfit h.p. welding torch 702 b. instruments and general shop outfit oxygen gas pressure 703 b. instruments and general shop outfit acetylene gas pressure 704 b. instruments and general shop outfit co2 gas pressure regulator 705 b. instruments and general shop outfit argon gas pressure regulator 706 b. instrument and general shop outfit surface plate 707 b. instrument and general shop outfit oil can 708 b. instrument and general shop outfit surface gauge universal 709 b. instrument and general shop outfit bench vice 710 b. instrument and general shop outfit hack saw tubular metal frameadjustable 711 b. instrument and general shop outfit snip sheet metal straight nose 712 b. instrument and general shop outfit snip sheet metal curved nose 713 b. instrument and general shop outfit anvil 714 b. instrument and general shop outfit stakes [ different types] 715 b. instrument and general shop outfit tin smith 716 b. instrument and general shop outfit wooden mallet /nylon mallet 717 b. instrument and general shop outfit round punch 718 b. instrument and general shop outfit electrical drill portable drillwith chuck and key 719 b. instrument and general shop outfit screw driver, plastic handle, 720 b. instrument and general shop outfit screw driver, plastic handle,flat tip 721 b. instrument and general shop outfit philips screw driver 722 b. instrument and general shop outfit screw driver, plastic handle,flat tip 723 b. instrument and general shop outfit soldering iron exchangeablecopper tip 724 b. instrument and general shop outfit knife folded stainless steel 725 b. instrument and general shop outfit tong tester (clamp on multimeter) 726 b. instrument and general shop outfit tenon saw 727 b. instrument and general shop outfit firmer chisel 728 b. instrument and general shop outfit rawal plug tool 729 b. instrument and general shop outfit fire extinguisher 730 b. instrument and general shop outfit fire buckets 731 b. instrument and general shop outfit d.e spanner 732 b. instrument and general shop outfit ring spanner 733 b. instrument and general shop outfit quick couples, process tubeadopter 734 b. instrument and general shop outfit tong close mouth and pick 735 b. instrument and general shop outfit welding table for gas/arc 736 b. instrument and general shop outfit flaring tool set, single type fortube. 737 b. instrument and general shop outfit swaging tool, punch type, setof size for tube. 738 b. instrument and general shop outfit bending spring external type,for copper tube 739 b. instrument and general shop outfit pipe cutter miniature forcopper tube 740 b. instrument and general shop outfit pinch of tool, for copper tube, 741 b. instrument and general shop outfit ratchet spanner 742 b. instrument and general shop outfit capillary plug gauge 743 b. instrument and general shop outfit piercing pliers & reversing valvewith access fitting 744 b. instrument and general shop outfit spanner double ended 745 b. instrument and general shop outfit ring spanner off set 746 b. instrument and general shop outfit wrench adjustable 747 b. instrument and general shop outfit wrench adjustable 748 b. instrument and general shop outfit wrench adjustable 749 b. instrument and general shop outfit valve key handle[treated asconsumable] 750 b. instrument and general shop outfit (hollo) punch hole for cuttinggasket 751 b. instrument and general shop outfit scissor, gasket cutting stainlesssteel 752 b. instrument and general shop outfit l allen key 753 b. instrument and general shop outfit t allen key set 754 b. instrument and general shop outfit pipe cutter with built in reamerand space cutter, for copper tube 755 b. instrument and general shop outfit pipe /tube bender lever type 756 b. instrument and general shop outfit spanner double ended 757 b. instrument and general shop outfit pipe wrench 758 b. instrument and general shop outfit lapping plate 759 b. instrument and general shop outfit hammer ball peen 760 b. instrument and general shop outfit puller 3 legged with flexiblearm 761 b. instrument and general shop outfit hand blower portablecomplete 762 b. instrument and general shop outfit spirit level precision metallic 763 b. instrument and general shop outfit tap set with matching drills 764 b. instrument and general shop outfit tap set with matching drills 765 b. instrument and general shop outfit refrigerant cylinder 766 b. instrument and general shop outfit heating kit with infrared bulb 767 b. instrument and general shop outfit plumbing hammer weight 768 b. instrument and general shop outfit cylinder 134 a 769 b. instrument and general shop outfit torque wrench 770 b. instrument and general shop outfit piercing valve 771 b. instrument and general shop outfit feeler gauge 772 b. instrument and general shop outfit four way reversible valve 773 b. instrument and general shop outfit vernier height gauge 774 b. instrument and general shop outfit tape measuring graduation in mm 775 b. instrument and general shop outfit voltmeter, ac/dc portable precision grade digital panel board type 776 b. instrument and general shop outfit ammeter, ac/dc portable precision grade digital panel board type 777 b. instrument and general shop outfit megger 778 b. instrument and general shop outfit wattmeter multi range up 779 b. instrument and general shop outfit multi meter digital type 780 b. instrument and general shop outfit k.w. meter 781 b. instrument and general shop outfit service oscillator 782 b. instrument and general shop outfit c.r.o single beam 783 b. instrument and general shop outfit c.r.o dual trace/ double beam 784 b. instrument and general shop outfit a.f.o oscillators 785 b. instrument and general shop outfit pressure gauge digital type 786 b. instrument and general shop outfit compound digital type gauge, 787 b. instrument and general shop outfit service man metal case thermometer 788 b. instrument and general shop outfit gas leak detector for halogen gas 789 b. instrument and general shop outfit electronic leak detector 790 b. instrument and general shop outfit sling psychrometer mounted on aluminum back, 791 b. instrument and general shop outfit stop watch 792 b. instrument and general shop outfit vernier caliper 793 b. instrument and general shop outfit micrometer outside measurement 794 b. instrument and general shop outfit multi meter analogue type 795 b. instrument and general shop outfit tachometer digital, multi range 796 b. instrument and general shop outfit micron vacuum gauge 797 b. instrument and general shop outfit sensor thermometer (digital) 798 b. instrument and general shop outfit fin straightened/fin comb. 799 b. instrument and general shop outfit filler gauge 800 b. instrument and general shop outfit wire gauge metric & british. 801 b. instrument and general shop outfit dial thermometer remote control, armored capillary dial 802 b. instrument and general shop outfit anemometer 803 b. instrument and general shop outfit compressors testers for small hermetic compressors 804 b. instrument and general shop outfit digital thermometer 805 b. instrument and general shop outfit temperature &humidity recorder 806 b. instrument and general shop outfit instrumentation screw driver set 807 b. instrument and general shop outfit digital weighing machine 808 b. instrument and general shop outfit split phase induction motor 809 b. instrument and general shop outfit bldc motor with controller 810 b. instrument and general shop outfit idu pulse motor 811 b. instrument and general shop outfit capacitor start induction motor 812 b. instrument and general shop outfit ac 3 phase motor, 400/50 hz 813 b. instrument and general shop outfit star delta starter 814 b. instrument and general shop outfit auto transformer starter 815 b. instrument and general shop outfit d.o.l starter 816 b. instrument and general shop outfit portable air lpg brazing kit 817 b. instrument and general shop outfit oxy acetylene complete 818 b. instrument and general shop outfit single door direct cool refrigerator, carrying with hfcand hc 819 b. instrument and general shop outfit frost free refrigerator 820 b. instrument and general shop outfit three/four door refrigerator ( inverter type) 821 b. instrument and general shop outfit core drill machine. 822 b. instrument and general shop outfit bench drilling machine 823 b. instrument and general shop outfit grinding machine 824 b. instrument and general shop outfit evacuating and refrigerant charging station, consist ofa) rotary two stage vacuum pump and motor (with gas ballast and anti such back)b) manifold with gauges and valves and capable of pulling vacuum up to 50 microns of hg and with provision of connecting to a microns level vacuum gaugeb) graduated charging cylinder with provision for temperature correction and all necessaryisolating valves 825 b. instrument and general shop outfit evacuating and charging station as above but fitted with weighing scale 826 b. instrument and general shop outfit two stage rotary vacuum pump,3or 4 cfm. 827 b. instrument and general shop outfit dry n2 cylinder 828 b. instrument and general shop outfit window a.c 829 b. instrument and general shop outfit split a.c 830 b. instrument and general shop outfit duct able split a.c 1.5 ton 831 b. instrument and general shop outfit recovery unit with cylinders 832 b. instrument and general shop outfit decibel meter 833 b. instrument and general shop outfit cassette air conditioner 834 b. instrument and general shop outfit de scaling pump set 835 b. instrument and general shop outfit fan coil unit 836 b. instrument and general shop outfit shell and tube, (small) 837 b. instrument and general shop outfit circulating water pump (small) 838 b. instrument and general shop outfit refrigerant cylinder 839 b. instrument and general shop outfit gauge manifold with gauges 840 b. instrument and general shop outfit shell and tube type condenser 841 b. instrument and general shop outfit rotary hermetic compressor 842 b. instrument and general shop outfit bottle cooler visible 843 b. instrument and general shop outfit deep freezer 844 b. instrument and general shop outfit display cabinet 845 b. instrument and general shop outfit water cooler storage type 846 b. instrument and general shop outfit water dispenser (hot and cold) 847 b. instrument and general shop outfit ice candy plant 848 b. instrument and general shop outfit air conditioning, direct system. 849 b. instrument and general shop outfit air conditioning, indirect system. (water cooled ) 850 b. instrument and general shop outfit package a/c 851 b. instrument and general shop outfit car a.c components (full kit)a) wobble plate compressor with mounting brackets.b) serpentine evaporatorc) parallel flow condenserd) hoses, tubes, receiver, ex.valve.e) electrical components &wiring harness 852 b. instrument and general shop outfit car ac tutorial model 853 b. instrument and general shop outfit bus ac tutorial model 854 b. instrument and general shop outfit automatic ice cube m/c 855 b. instrument and general shop outfit storage type water cooler (hot and cold) 856 b. instrument and general shop outfit vrf/vrv unit with two indoor units 2.5tr each and 5tr capacity out door unit complete with air cooled condenser,accessories and controls. 857 b. instrument and general shop outfit split a/c (inverter technology) 858 b. instrument and general shop outfit walk in cooler puf insulated for cold room 6x4.5x8 cft. 859 b. instrument and general shop outfit absorption system 860 b. tools, measuring instruments and general shop outfit try square 861 b. tools, measuring instruments and general shop outfit inside caliper 862 b. tools, measuring instruments and general shop outfit caliper outside 863 b. tools, measuring instruments and general shop outfit odd leg caliper 864 b. tools, measuring instruments and general shop outfit soil pot with brush 865 b. tools, measuring instruments and general shop outfit d. e. spanners 866 b. tools, measuring instruments and general shop outfit plumbers metal melting pot 867 b. tools, measuring instruments and general shop outfit pipe stock and dies complete with stocks,bushing, bushing holders, taps and wrenches sizes covered, to suit pipes 868 b. tools, measuring instruments and general shop outfit pipe vice 869 b. tools, measuring instruments and general shop outfit stillson pattern pipe wrenches 870 b. tools, measuring instruments and general shop outfit stillson pattern pipe wrenches 871 b. tools, measuring instruments and general shop outfit chain :pipe wrench 872 b. tools, measuring instruments and general shop outfit adjustable, spanner, a 375, is 6149 873 b. tools, measuring instruments and general shop outfit pipe bender, manually operated 874 b. tools, measuring instruments and general shop outfit leg vice, 75mm jaw on stand is 2588 875 b. tools, measuring instruments and general shop outfit hand drill 6mm capacity with drill chuck(electric) 876 b. tools, measuring instruments and general shop outfit drill twist (straight shank) 877 b. tools, measuring instruments and general shop outfit electric pump 878 b. tools, measuring instruments and general shop outfit hydraulic pressure machine for testingleakage in gi pipe fittings etc. 879 b. tools, measuring instruments and general shop outfit pipe bender (hydraulic type) 880 b. tools, measuring instruments and general shop outfit chase cutter (electric) 881 b. instruments and general shop outfit air impact wrench with standard accessories 882 b. instruments and general shop outfit air ratchet with standard accessories 883 b. instruments and general shop outfit ammeter 884 b. instruments and general shop outfit angle plate 885 b. instruments and general shop outfit battery –charger 886 b. instruments and general shop outfit blow lamp 887 b. instruments and general shop outfit bucket, sponge, squeegee, chamois & tack rags 888 b. instruments and general shop outfit colour matching cards /panels (magnetic, chromalux card orprimed metal) 889 b. instruments and general shop outfit copper bit soldering iron 890 b. instruments and general shop outfit cylinder bore gauge capacity 891 b. instruments and general shop outfit depth micrometer 892 b. instruments and general shop outfit dial gauge type 1 gr. a(complete with clamping devices and stand) 893 b. instruments and general shop outfit dividers 894 b. instruments and general shop outfit engineers square 895 b. instruments and general shop outfit files assorted sizes and types including safe edge file (20nos) 896 b. instruments and general shop outfit garage rack 897 b. instruments and general shop outfit hand shear universal 898 b. instruments and general shop outfit lifting jack screw type 899 b. instruments and general shop outfit multimeter digital 900 b. instruments and general shop outfit outside micrometer 901 b. instruments and general shop outfit outside micrometer 902 b. instruments and general shop outfit paint measuring / mixing stick& jug sets 903 b. instruments and general shop outfit panel buffing machine 904 b. instruments and general shop outfit set of stock and dies metric 905 b. instruments and general shop outfit shertinmans 906 b. instruments and general shop outfit spirit level 907 b. instruments and general shop outfit taps and wrenches metric 908 b. instruments and general shop outfit trammel 909 b. instruments and general shop outfit v block 910 b. instruments and general shop outfit verniercaliper 911 b. instruments and general shop outfit voltmeter 912 c. general installation/ machineries angle grinder 913 c. general installation/ machineries belt sander (narrow surface) 914 c. general installation/ machineries body shell for painting light motor vehicle of different manufactures 915 c. general installation/ machineries compressed air line 916 c. general installation/ machineries die grinding kit 917 c. general installation/ machineries disc sander 918 c. general installation/ machineries drilling machine bench to drill up to 12mm dia along withaccessories 919 c. general installation/ machineries dust extraction connections (vacuum) 920 c. general installation/ machineries motor vehicle suitable for body painting light motor vehicle of different 921 c. general installation/ machineries paint surface film thickness gauge (electronic) 922 c. general installation/ machineries random /dual action orbital sander 923 c. general installation/ machineries spray gun & mixing equipment cleaning machine(explosionproof) & bench 924 g. list of tools & accessories for pneumatics and hydraulics compressor unit 925 g. list of tools & accessories for pneumatics and hydraulics pneumatic trainer kit, each consisting ofthe following matching components and accessories: g. list of tools & accessories for pneumatics and hydraulics i. single acting cylinder g. list of tools & accessories for pneumatics and hydraulics ii. double acting cylinder g. list of tools & accessories for pneumatics and hydraulics iii. 3/2 way valve g. list of tools & accessories for pneumatics and hydraulics iv. 3/2 way valve g. list of tools & accessories for pneumatics and hydraulics v. one way flow control valve g. list of tools & accessories for pneumatics and hydraulics vi. 5/2 way valve g. list of tools & accessories for pneumatics and hydraulics vii. 5/2 way valve g. list of tools & accessories for pneumatics and hydraulics viii. 5/2 way pneumatic actuatedvalve g. list of tools & accessories for pneumatics and hydraulics ix. 3/2 way roller lever valve g. list of tools & accessories for pneumatics and hydraulics x. shuttle valve (or) g. list of tools & accessories for pneumatics and hydraulics xi. two pressure valve (and) g. list of tools & accessories for pneumatics and hydraulics xii. pressure gauge g. list of tools & accessories for pneumatics and hydraulics xiii. manifold with self closing g. list of tools & accessories for pneumatics and hydraulics xiv. pushbutton station for electrical signal input g. list of tools & accessories for pneumatics and hydraulics xv. relay station g. list of tools & accessories for pneumatics and hydraulics xvi. 3/2 way single solenoid valve g. list of tools & accessories for pneumatics and hydraulics xvii. 5/2 way single solenoid valve g. list of tools & accessories for pneumatics and hydraulics xviii. 5/2 way double solenoid valve g. list of tools & accessories for pneumatics and hydraulics xix. power supply unit, g. list of tools & accessories for pneumatics and hydraulics xx. profile plate, anodised aluminium 926 g. list of tools & accessories for pneumatics and hydraulics pneumatic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: 927 g. list of tools & accessories for pneumatics and hydraulics carrier for mounting components, such as pb & relay boxes. 928 g. list of tools & accessories for pneumatics and hydraulics cut section model for pneumaticcomponents 929 g. list of tools & accessories for pneumatics and hydraulics hydraulic trainer kit, each consisting of the following matching components and accessories: g. list of tools & accessories for pneumatics and hydraulics i. hydraulic power pack g. list of tools & accessories for pneumatics and hydraulics ii. pressure relief valve g. list of tools & accessories for pneumatics and hydraulics iii. drip tray, steel g. list of tools & accessories for pneumatics and hydraulics iv. pressure gauge g. list of tools & accessories for pneumatics and hydraulics v. four way distributor g. list of tools & accessories for pneumatics and hydraulics vi. double acting hydraulic cylinder g. list of tools & accessories for pneumatics and hydraulics vii. suitable weight g. list of tools & accessories for pneumatics and hydraulics viii. mounting kit for weight g. list of tools & accessories for pneumatics and hydraulics ix. 3/2 way directional control valve g. list of tools & accessories for pneumatics and hydraulics x. 4/2 way directional control valve g. list of tools & accessories for pneumatics and hydraulics xi. 4/3 way directional control valve g. list of tools & accessories for pneumatics and hydraulics xii. non return valve. g. list of tools & accessories for pneumatics and hydraulics xiii. pilot operated check valve g. list of tools & accessories for pneumatics and hydraulics xiv. one way flow control valve g. list of tools & accessories for pneumatics and hydraulics xv. t connector with self sealing coupling nipples (2 nos.) and quick coupling socket (1 no.). g. list of tools & accessories for pneumatics and hydraulics xvi. profile plate, 930 g. list of tools & accessories for pneumatics and hydraulics hydraulic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: 931 g. list of tools & accessories for pneumatics and hydraulics cut section models for hydraulic components 932 general shop outfit surface plate c.i/granite with stand and cover 933 general shop outfit marking table (mild steel) 934 general shop outfit pipe bender machine spool type with stand manually operated. 935 general shop outfit angle plate 936 general shop outfit machine vice swivel base 937 general shop outfit machine vice swivel base 938 general shop outfit torque wrench (standard/ratchet type) 939 general shop outfit power tools for fastening 940 general shop outfit temperature gauge 941 general shop outfit lapping plate 942 general shop outfit anvil 24 sq. inches working area with stand 943 general shop outfit swage block 944 general shop outfit portable abrasive cut off machine 945 general shop outfit fuel injection test bench for calibration of fuel pump 946 general shop outfit electrical test bench 947 d. measuring instruments micrometer outside 948 d. measuring instruments micrometer outside 949 d. measuring instruments micrometer outside 950 d. measuring instruments micrometer outside ...
45999975 supply of set of spares for nose assemblyset of spares for nose assembly,set of spares for nose assembly for 3/4 hyd. installation tool model no. ohpl i 1219 n3 (oe m orione). each one set consist 1. anvil pn op0805612 = qty 1 no., 2. collet pn op0805613 = qty 1 no., 3. follower pn op0805614 = qty 1 no., 4. sleeve pn op0805615 = qty 1 no., 5. release pn op0810616 = qty 4 nos., 6. ejector pn op0810617 = qty 4 nos. [ warranty period: 30 months after the date of deliver y ] ]...
45495743 supply of machines and equipments for civil engineering lab 1 direct reading transit theodolite 2 with tripod 2 dumpy level with tripod 3 prismatic compass with tripod 4 cross staff 5 optical square 6 ranging rod (steel) 4m 7 ranging rod (steel) 3m 8 leveling staff (4m) 9 leveling staff (5m) 10 leveling staff (6m) 11 engineers measuring chain 30m 12 metallic tape 30m, 13 arrows (metal) 14 mallet and pegs (wooden) 15 spirit level 16 invar tape 30m 17 surveyor compass 18 stand 19 chain 20 metallic tape 10m, 21 pegs 22 hammer 23 plane table and its accessories 24 metallic tape 5m, 25 prism square 26 clinometer 27 tachometer 1 compaction factor apparatus 2 slump test apparatus 3 vee bee consisto meter 4 cement mortar moulds 5 cylindrical moulds 6 cube moulds 7 le chatelier flask 8 le chatelier apparatus 9 le chatelier water bath 10 standard vicat’s apparatus 11 flexure strength testing machine 12 cement tensile testing machine 13 needle vibrator 14 digital weighing balance 15 digital platform balance 16 cement autoclave 17 trowel 18 spatulla 19 guinia 20 spirit level 21 floor tile testing machine (flexure and abrasion) with all accessroies 22 weight 23 weight hanger 24 steel scale 25 micrometer 26 thickness and length gauge for flakness and elongation index 27 i.s. sieves set 28 rebar detector 29 enfflorscence test apparatus 30 automatic mortar mixer, digital, capacity 5 l 31 rebar locators, diameter and cover meters with software 1 ph meter 20 x 2 line back lighted lcd display., ph meter complies to usp and din standards, alphanumeric splash waterproof polyester keyboard with soft keys., range 0° to 150° c. no’s 1 2 turbidity meter 0 10,000 ntu , ± 2% of reading plus 0.01 ntu (0 to 1000 ntu) no’s 1 ± 5% of reading (1000 to 4000 ntu) ± 10% of reading (4000 to 10,000 ntu) , response time: less than 6 seconds, sample size: 30ml, operating temperature: 0° 50°c 3 test tube glass test tube 150 mm tall x 16 m with 14 mm inside diameter. approximate volume is 22 ml. borosil no’s 24 4 magnetic stirrer with hot plate number of stirring positions: 1 no’s 1 calibration: automatic calibration type of drive motor: motorless magnetic coil type display option/output read out option: digital magnetic stirrer is: with a hot plate or some other means for heating the liquid controller type: electronically controlled and programmable speed control accuracy of set speed (+/ ) (rpm): 0 maximum stirring capacity per position: 2000 milliliter ceramic top plate material, digital front panel, last run memory ce certified product (seller to furnish supporting document to buyer on demand) speed speed mode: variable speed minimum speed possible (rpm): 50 maximum speed (rpm) of variable speed mode equipment: 1600 dimensions external dimension: (height )200 millimeter external dimension: width 200 millimeter external dimension: depth: 50 millimeter body material: stainless steel finish of body material: powder coated top plate finish: ceramic coated stir bar stir bar cover material: ptfe quoted alnico magnet stir bar length: 200 millimeter top plate top plate area shape: circular circular top plate diameter: 1000 millimeter top plate finish: ceramic coated 5 burette 50 ml, made of borosil no’s 6 6 burette. stand with rod,clam & boss head base 8 x 5, rod 2411 long, 1.1tree finger clamp no’s 10 7 conical flask 250 ml, made of borosil no’s 6 8 pippette, 25 ml, made of borosil no’s 10 9 rubber gloves, nitrile rubber (l size) box 4 10 apron white cloth lab apron (m size) no’s 5 11 fluoride ion meter (with fluoride electrode) type / nomenclature / protection no’s 1 type of meter / analyzer: bench type functional nomenclature: multi parameter water quality analyzer ingress protection (main unit): ip 56 calibration: automatic compensation / correction temperature correction: automatic salinity correction: automatic display / storage type of display: lcd with backlight display digit size: 30 millimeter number of digits in display: 5 number of parameters displayed simultaneously: 3 memory (in data sets): 500 internal memory (gb): 64 date /time stamp in entries: yes connectivity interface: usb, rs 232 power source: alkaline batteries (non rechargeable), mains (230 ±10 volts / 50 hz ac) battery size, if non rechargeable battery: aa battery chemistry, if rechargeable battery: li ion voltage of each battery 1.5 volt number of batteries required for operation: 4 number of batteries inclusive in the scope of supply: 4 battery capacity (mah): 800 battery life: 800 hour suitable adapter to be supplied to make the equipment work on 230 v ± 10 %, 50 hz: yes 12 prestaltic pump flow range – 0.1ml/hr to 1000ml/hr accuracy – ±2% digital display of functions and time auto stop with audible no’s 1 alarm battery back up stores memory in case of power failure. 13 high volume air sampler flow rate 39 to 60 cfm for mfc; typically 42 to 45 cfm for vfc; volumetric flow control accuracy ±1% deviation over 24 hr period;power requirements 110/220 â± 10v, 100w; precision of pressure stabilization 0.05 mpa; flow/pressure recorder with circular charts, 4 (10 cm) dia.; range 10 to 65 cfm no’s 24 14 nessler tube borosil glass, 3.3mm thick, and 100ml capacity no’s 6 15 glass test tubes glass test tube 150 mm tall x 16 m with 14 mm inside diameter. approximate volume is 22 ml. made of borosil no’s 24 16 laboratory hot air over digital laboratory over (18x18x18), hot oven 450mm digital no’s 1 17 thermometer digital display, accuracy +/ 1c no’s 3 18 vertical autoclave product: vertical autoclave. pressure: 10 20 psi, usage: laboratory, power rating: 1.5 kw, size: 22l, outer material: mild steel, inner material: no’s 1 stainless steel 19 filtration assembly with oil free vacuum pump filtration assembly consisting of suspended solids filter holder with filter support for 47 mm dia and borosil glass filtration flask, capacity 1 ltr vacuum pipe, oil free vacuum pump. i. oil tree vacuum pump 25 litr , 2.ss holder 47 mm, 3 glass flask 1000ml set 1 20 petri dish borosilicate glass petri dish 90mm no’s 10 21 silica crucible (50m1) heat resistant, strong build quality {10 piece of each). can be used in muffle furnace at high tempareture up to 1000 degree celcius no’s 10 22 silica crucible (100 ml) heat resistant, strong build quality {10 piece of each). can be used in muffle furnace at high tempareture up to 1000 degree celcius no’s 10 23 bod bottle 300ml bottle , made of borosil no’s 30 24 digital cod digester (for 10 ml cod vials) digestion capacity 10 16 vials vial volume maximum 10m1 vial dimension 16 x 100 mm digestion temperature 20c 200° c no’s 1 25 chloroscope square unbreakable test tube 2 nos, glass dropper with rubber test 1no, o toluidine reagent 125ml, packed in thermocol box, to check chlorine in drinking water from 0.25ppm to 2ppm no’s 6 26 porcelain dish 80mm dia, 40 ml no’s 6 27 measuring cylinder 250 ml made of borosil no’s 6 28 beaker 250 ml made of borosil no’s 6 29 filter paper 42 & 45 no. no’s 12 30 funnel made of borosil no’s 6 geo tech. engg 1 i.s. sieves 20 cm diameter brass aperture size 4.75 mm, 2.36mm, 1.18mm, 600micron, 300 micron,150 micron and 75 micron as per is 460 sieves 20 cm diameter brass aperture size 4.75 mm, 2.36 mm, 1.18mm, 600 micron, 300 micron,150 micron and 75 micron as per is 460 set 2 2 pycnometer as per is:2386 ( part 3 ) consist of a 1 kg glass jar with brass cone no’s 6 3 liquid limit device casagrande grooving tools and gauge block with ac supply compliance with is:2720 (part 5), is:9259 no’s 6 consists of a hard rubber base casagrande grooving tool gauge block 4 plastic limit set glass plate, flexible spatula, brass / ss rod, moisture dish & porcelain dish. no’s 6 5 core cutter as per is:2720 (part 29), min. 100 mm dia x 130 mm long, steel dolly 25 mm high and 100 mm dia,rammer with steel rod. no’s 4 6 density bottle 100 ml, made of borosilicate no’s 5 7 density bottle 50 ml, made of borosilicate no’s 5 8 proctor test apparatus for heavy compaction proctor test apparatus for heavy compaction, material mild steel as per the is:2720 (part 8), rammer and base plate, made of mild steel no’s 1 150 mm dia, 127.3 mm height 2,250 ml volume. rammer: 4.9 kg 9 direct shear apparutus . moterised with 12 speed . as per is : 2720 ( part xiii ) ref. standards is :11229, 2720 (part 13) no’s 1 type of shear : direct / residual measurement operation : motorised rates of strain (mm/min) : 1.25, 0.625, 0.25, 0.125, 0.05, 0.025, 0.01, 0.005, 0.002, 0.001, 0.0004, 0.0002 specimen size : 60 x 60 x 25 mm digital indicator, load cell 2kn, displacement sensor range : 0 20mm. shear box assembly, this assembly comprises of : halves of the shear box 2 nos. plane gripper plate 2 perforated gripper plate 2 porous stone 2 top loading pad 1 base plate 1 specimen cutter 1 min normal stress 3 kg/cm2 operation : motorised 10 laboratory vane shear apparatus as per the is:2720 (part 30) with special motor, rotation 0.10/sec. no’s 1 rate of rotation : 1/60 rpm suitable for operation on 220 v, 50 hz, single phase, ac supply. container 1 no.set of 4 springs, (one each of capacity 2 kg cm, 4 kg cm, 6 kg cm and 8 kg cm min) 11 triaxial shear test apparatus speeds between 0.0005 mm/min and 6.00 mm/min. no’s 1 maximum platen dia : 130mm tri axial cell , stationary bushing,38mm dia: ref standard: is : 2720 (part xii) for testing specimen of size 38mm dia x 76mm long. • triaxial cell consists of perspex chamber with anvil and loading plunger • the cell is easily split by releasing four type rods. • it is leak proof upto 10 bar (10 kg/cm2) fluid pressure. • an oil plug and an air vent are provided for introducing a thin layer of oil over water. this provides effective sealing at the plunger for long duration tests. • the cell is fitted with four sleeve packed valves of no volume change type of base. cell consisting of followings: • top loading pad, perspex, 38 mm dia. 1 no. plain perspex disc 38mm dia x 6 mm thick 1 pair. porous stone 38mm dia x 6 mm thick. 1 pair. sheath stretcher for 38 mm dia specimen 1 no. two way split former for 38 mm dia specimen 1 no. rubber sheath for 38 mm dia specimen 12 nos. drainage tube (short), 38 mm 4 nos. drainage tube (long), 38 mm 4 nos. “o’ rings for 38mm dia specimen 4 nos. split mould, 38mm dia 1 no. top loading pad 38mm (plain) 1 no. max pressure 12kg/cm2 . oil pump 1 variable pressure 16 bar pressure suitable for operation on 220 v, 50 hz, single phase,ac supply. •pressure transducer, 20 bar (20 kg/cm2) capacity, an lvdt (displacement sensor) having a range of 0 20mm mm and a 3 channel digital indicator digital indicator : mode of display : micro controller multi line alpha numeric vfd display for all simultaneous channel power supply voltage : 220v, 50hz, single phase load cell: capacity : 10 kn load cell excitation : 5 v, dc 12 consolidation apparatus as per is:2720 (part xv), analogue no’s 1 should consolidation cell assembly min 3 nos fixed ring with guide ring— min 3 nos channelled base with water inlet— 3 nos water jacket — 3nos different set of weights watertank with assembly, 13 sieve shaker sieve shaker, motorized, with built in digital timer, • a digital timer adjustable from 0 99 minutes is incorporated as an integral part of the equipment. no’s 1 • the sieve shaker can carry up to 8 sieves of 20cm diameter, also supplied with 30cm adaptor. it is driven by a ¼ hp geared motor. , • the sieve table is inclined from the vertical axis and the direction of inclination changes progressively in the clockwise direction. in addition to the gyratory motion of the table, there is a tapping motion as well. suitable for operation on 220 v, 50 hz, single phase, ac supply. 14 electronic balance upto 500g, and 5 kg no’s 1 15 glass measuring cylinder 1000 ml no’s 5 16 stop watch accuracy : 0.01 seconds no’s 2 17 hydrometer apparatus hydrometer, range: 0 20, 20 40, 40 60, 60 80, & 80 100 no’s 5 18 metre scale 300 mm length, steel made no’s 2 19 shrinkage limit set as per is : 2720 (part 6), porcelain evaporating dish, shrinkage bath, glass cup, min. three metal prongs, perspex plain plate spatula, glass cylinder, 25 ml x 0.5 ml, mercury. no’s 2 20 sample extractor application soil extractor, capacity 5 ton, automation grade manual no’s 1 21 infra red moisture metre as per the is: 2720 (part 2) no’s 1 the speed of drying (about 30 min), the infrared radiation is controlled by a voltage regulator. the instrument is provided with an indicator lamp. the balance scale (drum) is divided in terms of moisture percentage on wet weight basis, which are read directly from it. graduations are from 0 to 100% in 0.2 % divisions. suitable for operation on 220 v, 50 hz, single phase,ac supply. capacity: min 5g approx. sensitivity : min 10 mg approx. range : 0 to 100% moisture content on wet weight basis. reading accuracy : min ± 0.20% probable error : min ± 0.25% in the lower range upto compared to 25% and ± 1% for moisture contents oven methods : above 50% equipment consisiting of : infra red lamp thermometer (l shaped) 22 unconfined compression test digital load frame with lcd 50 kn capacity with 4 speed variations. no’s 1 • horizontal clearance 265 mm • vertical clearance 700 mm • maximum platen dia 130 mm • maximum platen travel 100mm • ram dia 50mm • suitable for operation on 220 v, 50 hz, single phase, ac supply. • ring capacity 2 kn • dial gauge 25 mm, 0.01 mm least count. • mould 38 mm dia × 76 mm long • rubber sheath 38 mm dia specimen 23 sand bath device with tray, stove, palet, knife, steel top with powder coated, 230v, single phase no’s 1 24 non corridible air tight container or can 100 ml, 200 ml, 500 ml, 1000 mlset of 6 for each nos 24 25 thermometer 0.5c 60c no’s 2 26 water bath 15 litre capacity, temperature controlled, led water bath no’s 1 mom lab. 1 beam deflection apparatus structural lab a mild steel beam 2.5 cm x 3 mm in cross section and 100 cm long is pinned to two supports 70 cm apart situated symmetrically. one of the ends can be fixed or given a known slope by applying a known moment at the end with the help of suspended loads. at the other end also a known moment can be applied at various points along the span of the beam. no’s 1 2 abrasion testing machine for glezed tile voltage 230, power 100 watt, 50 hz, single phase ac supply no’s 1 3 flexure strength testing machine flexure testing machine electrically operated, material of construction: no’s 1 weight of the load frame: min. 130kg hydraulic system: with min. 15 liters, hydraulic oil feed and fuel pump separately, 0.5 hp, 1 ph, 220v ac motor driven two speed hydraulic pump.standard confirm to: conforms to is 516 and is : 14858, machines conforming to astm c39. ...
45304746 auction sale of scrap and condemned machine & plants consisting of m&p no.10240 pnu power hammer with anvil. conditions: [1] as is where is basis[2] minimum dismantle in 2 parts [3] all electrical fittings &electrical motor are included from sale. [4] before bidding bidders are advised to inspect and tally every details of the lot as appearing in catalogue which is published in ireps portal with the actual material in ground. no complaints/claim by the purchaser will be entertained in this regards after e auction sale. [5] custodian may allow purchaser to bring crane if it is required and justified.[6] cutting/ dismantling of machine is to be done in such a way so that no adjacent machine, structure, installation or machine accessories etc get affected in any way....
45107466 supply of machines and laboratory equipment’s for physics and mechanical engineering 1 determine resultant of concurrent coplanar force system using force polygon table 2 determine unknown force in a concurrent balance force system using lami’s theorem 3 find reactions at the supports of a simply supported beam and compare the results with analytical values. 4 determine the support reactions for simply supported beam by a) beam reaction apparatus b) circular dial type weight 5 determine coefficient of friction on horizontal and inclined plane. 6 determine the co efficient of friction between two surfaces by a) angle of repose methods b) friction plane method 7 find the coefficient of friction betweenbelt and pulley in a belt friction set up 8 determine the centroid of geometricalplane figures (squares, rectangle,triangle) 9 determine the moment of inertia of a fly wheel 10 find m.a, v.r and efficiency of screw jack. 11 find m.a, v.r and efficiency ofdifferential wheel and axle 12 calculate the efficiency of singlepurchase crab winch and doublepurchase crab winch 13 determine forces in jib crane. 14 determine the efficiency of worm andworm wheel. 15 abels flash & fire point apparatusflash point temperature 70 16 cleveland flash & fire point apparatus 17 pensky martin flash & fire point apparatus 18 say boly viscometer digital 19 bomb calorimeter to test calorific value of solid & liquid fuels 20 junkers gas calorimeter (gaseous fuels) to test calorific value of gaseous fuels 21 conradsons apparatus for carbon residue test 22 two stroke petrol engine, constant speed, air cooled, horizontal petrol engine, 3bhp, 1500 rpm 23 two stroke diesel engine 24 single cylinder 4 stroke diesel engine test rig coupled with ac alternatorconstant speed, water cooled, vertical diesel engine, 5 bhp, 1500 rpm compression ratio 16.5:1 brake drum radius 0.185 morifice diameter 15mm 25 crdi 4 stroke diesel engine for dismantling and assembling with fault simulation board 26 single cylinder 4 stroke petrol engine 27 verification of bernaullis theorem 28 co efficient of discharge of venturimeter, orifice meter. 29 centrifugal pump test rig. (constant & variable speed) 30 determination of coefficient of friction of flow through pipes 31 minor losses in pipes 32 reciprocating pump test rig (with motor) 33 francis turbine test rig. 34 pelton turbine test rig. 35 vapour compression refrigeration trainer test rig: 36 condenser: 37 evaporator: steel material: cross sectional view model of forced circulation evaporator. 38 evaporator: steel material: cross sectional view model of direct contact evaporator. 39 sling psychrometer: 40 refrigeration tool kit and complete refrigeration kit. 41 wood turning lathe machine 42 circular saw machine. straight rise fall& tilting type 43 universal wood working machine 44 band saw machine with all accessories. 45 steel rulescale 1mtr. 46 scriber 47 marking gauge 48 mortise gauge 49 dividers 50 rip saw 51 try square 52 coping saw 53 firmer chisel 54 gauge chisel 55 iron jack plane 56 trying plane 57 rasp 58 hand drill 12 mm 59 gimlet drill 60 clamping vice 61 c clamp 62 cross pin hammer 63 ball pin hammer 64 claw hammer 65 sledge hammer 66 mallet 67 open hearth furnace. 68 anvil 69 hand hammer 70 double handed sledge hammer 71 tongs 72 chiesel tongs 73 pick up tong. 74 pipe mouth. 75 round mouth hollow. 76 hot chiesel 77 cold chiesel 78 hardle set 79 punches; 80 81 82 83 84 drift 85 86 87 88 89 flatter 90 fuller 91 swage 92 swage block with stand. 50. 93 set hammer 94 leg vice 95 hammer 96 smith square 97 calliper 98 angle mouth tongs 99 bench vice 100 leg vice 101 pipe vice 102 try square 6 and l square 103 scriber surface gauge 104 dot punch (4 & 8) 105 centre punch (4 & 8) 106 surface plate 24 x 24 107 angle plate. 108 steel rule. 109 inside vernier calliper. 110 outside vernier calliper 111 micrometer. 112 divider 113 outside calliper. 114 inside calliper. 115 spring callipers 116 feeler gauge set rough file 117 118 119 120 bastered file 121 122 123 124 second cut file 125 126 127 128 smooth file 129 130 131 132 dead smooth file 133 134 135 136 files; 137 flat file 138 square file 139 triangular file 140 round file 141 half round file 142 knife edge file 143 diamond file chiesel 144 flat 145 cross cut 146 half round 147 diamond point 148 ball pin hammer. 149 straight pin hammer 150 cross pin hammer. 151 drills tapered shank & parallel shank 152 tap set. high speed 153 bench drilling machine. 154 portable drilling machine 155 pipe wrench 156 chain wrench 157 lathe machine light duty 158 lathe machine 159 gas welding/ cutting machine 160 arc welding machine 161 solder iron machine 162 fire extinguisher 163 sheet bending and cutting operation 164 sheet metal and hand tools 165 slip gauge complete set 166 a) vernier caliper 167 b) vernier caliper 168 c) vernier caliper 169 d) vernier caliper 170 e) vernier caliper 171 f) vernier caliper dial 172 f) vernier caliper dial 173 f) vernier caliper dial 174 a) micrometer outside 175 b) micrometer outside 176 c) micrometer outside 177 d) micrometer outside 178 e) inside micrometer 179 f) inside micrometer 180 sine bar complete set 181 vernier bevel protector 182 straight edge 183 gauge sets (radius, thread) 184 thread plug gauges (set of 5) 185 plain plug gauges (set of 5) 186 taper plug gauges (set of 5) 187 thread micrometer 188 autocollimator 189 profile projector 190 floating carriage micrometer 191 magnetic dial indicator with dial gauge 192 ring gauge 193 surface plate 194 snap gauge 195 comparator 196 roughness tester 197 stain gauge 198 lvdt 199 flow measurement apparatus 200 temp. measurement 201 tachometer digital 202 tachometer analog 203 transducer set 204 height gauge 205 pressure measurement apparatus 206 torque measurement apparatus 207 strain mesurement trainer apparatus 208 load cell trainer 209 thermo couple calibration trainer 210 speed measurement trainer 211 mounting dead weight safety valve 212 spring loaded safety valve 213 model of steam stop valve 214 model of pressure guage 215 model of water level indicator 216 model of fusible plug 217 model of blow off cock 218 accessories model of economizer 219 model of air preheater 220 model of superheater 221 model of steam separator 222 model of steam trap 223 model of injector 224 multi stage reciprocating compressor 225 two stroke petrol engine, contant speed, air cooled, horizontal petrol engine, 3 bhp, 1500 rpm 226 two stroke diesel engine 227 single cylinder 4 stroke diesel engine test rig. coupled with ac alternator constant speed, water cooled, vertical diesel engine, 5bhp, 1500 rpm 228 single cylinder 4 stroke petrol engine 229 1. cornish boiler model 230 2. lamont boiler model 231 3. benson boiler model 232 4. lancashire boiler model 233 5. locomotive boiler model 234 6. loeffler boiler model 235 7. veloxboiler model 236 universal testing machine computerised, 6 pillar type with hydraulic jaws. capacity 60 ton 237 digital torsion testing machine 238 digital spring testing machine 239 pendulum impact tester 240 rockwell hardness tester 241 laboratory metallurgical microscope 242 eeciflux power type equipment for magnetic particle test weight 45kg, model name/number 1500, 1500 2 and 2000 amps heavy duty cycle 0.5 sec off, type ac and hwdc output, dimension (l*w*h) 550mm x 240mm x240mm. 243 direct shear test apparatus motorised 244 vernier caliper 245 micrometer screw gauge 246 spherometer 247 spring oscillator 248 bar pendulum 249 pullingger’s apparatus 250 searle’s apparatus 251 stokes’s law apparatus 252 photo electric cell experiment 253 numerical aperture of an optical fiber 254 he ne/diode laser 255 fly wheel 256 vernier caliper 257 micrometer screw gauge 258 spherometer 259 spring oscillator 260 bar pendulum 261 p n junction diode 262 parallel plate capacitor 263 photo electric cell 264 numerical aperture of an optical fiber. 265 he ne/diode laser ...
42782814 supply of pneumatic power hammer 55 kg. specification: max stroke 250 per minute; 55kg pneumatic air hammer machine for blacksmith with 600 620 kg anvil; production capacity: 55 kg hammer machine.pneumatic power hammer 55 kg. specification: max stroke 250 per minute; 55kg pneumatic air hammer machine for blacksmith with 600 620 kg anvil; production capacity: 55 kg hammer machine.,pneumatic power hammer 55 kg. specification: max stroke 250 per minute; 55kg pneumatic air hammer machine for blacksmith with 600 620 kg anvil; production capacity: 55 kg hammer machine. [ warranty period: 30 months after the date of delivery ]...
42676262 bids are invited for hammer ball peen 50 grams , wooden mallet small i s 2022 , surface plate 400 x400 mm grade i , v blocks with clamps , combination set 200 mm , scribing block, universal, 300 mm , tap and die set to cut b.s.f and b.s.w. and metric threads sizes no.6 to m 12 , screw pitch gauge to cover above threads , saw plumber 300mm , stove melting solder , snip straight 250mm , snip bend 250mm , tenon saw , hand saw. , mortise chisel , firmer chisel , mallet medium is 2922 , jack plane , gas welding set with oxygen acetylene cylinder , goggles pair welder 100 mm , brush steel wire 150x 50 mm , pliers combination, 200 mm , blow lamp 500 mililitre , scribing gauge , pot hook , branch gimlets , anvil 50 or 63 kg. is 510 , flat smithy tong , d.e. pedestal grinder with two wheels 175mm rough and smooth , bench drilling machine with chuck and key upto 15mm capacity , ring guage 15 mm, 20mm, 25mm, 32mm total quantity : 145...
42661849 bids are invited for fitter toolkit steel rule with metric & british graduation try square. caliper hermaphrodite spring type divider spring type scriber centre punch screw driver chisel cold flat hammer ball peen with handle hammer ball peen with handle. file flat second cut file half round second cut hacksaw frame fixed type safety goggles. dot punch straight edge steel spirit level metal type 2 stud extractor ezy out micrometer outside. micrometer inside with extension rods. vernier bevel protractor blade with acute angle attachment screw pitch gauge metric wire gauge, metric standard. surface plate c.i / granite with stand and cover marking table ( mild steel ) universal scribing block. v block pair with clamps angle plate punch letter set. punch number set. portable hand drill ( electric ) drill twist taper shank file triangular smooth file round second cut feeler gauge file triangular second cut. file flat second cut safe edge. file swiss type needle file card. oil can pliers combination insulated wooden handle forged soldering iron copper bit. blow lamp spanner double ended spanner double ended spanner double ended spanner double ended spanner double ended spanner double ended spanner double ended spanner double ended interchangeable ratchet socket set double ended tubular box spanner set with tommy bar. glass magnifying clamp toolmaker hand reamer set ( taper pin straight flute ) machine reamer parallel ( helical flute ) scraper flat scraper triangular scraper half round chisel cold crosscut& diamond point. chisel cold round nose drill chuck with key pipe wrench pipe vice adjustable pipe die set bsp wheel dresser ( one for 4 units ) star / dresser with holder machine vice swivel base machine vice swivel base sleeve drill morse lockers with 8 drawers ( standard size ) . machine vice. wing compass. hand hammer with handle. torque wrench ( standard / ratchet type ) power tools for fastening different profile gauges ( plate type ) for demonstration knurling tool ( diamond, straight & diagonal ) indexable boring bar with inserts temperature gauge dowel pin ( straight ) standard tap screws lapping plate medium carbon heat treated alloy steel metric studs and bolts along with nuts ( for display ) of standard length ( may be manufactured in house ) caps screws drill gauges cast iron globe valve ( flanged type ) c.i. sluice / gate valve ( flanged type ) stop cock m.s. pipe g.i. pipe slip on forged steel flange bolt & nut with washer ( may be manufactured in house ) pipe threading die with handle jigs & fixture ( sample ) for demonstration ( may be manufactured in house ) pulleys ( for v belt or flat belt ) steel keys ( may be manufactured in house ) damaged old spur gear v belt and flat belt packing gasket washer, clutch, keys, jib, cotter &circlip hollow punch drill drift ( may be manufactured in house ) bearing different types lifting sling bearing extractor pulley extractor trammel pocker prick punch mallet. aviation snips straight cut flat headed hammers with handle. planishing hammer. snip bent left cut stake hatchet with leg. stake grooving. slip gauge as johnson metric set. gauge snap go and not go gauge plug gauge telescopic set. dial test indicator on stand sine bar dial vernier caliper. ( universal type ) screw thread micrometer with interchangeable. pitch anvils for checking metric threads 60. depth micrometer. 0 25 mm digital vernier caliper. digital micrometer outside. comparators gauge dial indication with stand and bracket. engineers try square knife edge surface roughness comparison plates digital vernier caliper vernier bevel protector carbide wear block. lathe tools h.s.s. tipped set. lathe tools bit. lathe tools bit. lathe tools bit. arm strong type tool bit holder. arm strong type tool bit holder. arm strong type tool bit holder. stilson wrenches pipe bender machine spool type with stand manually operated. adjustable pipe chain tonge to take pipes adjustable spanner. compressor unit pneumatic trainer kit, each consisting of the following matching components and accessories i. single acting cylinder ii. double acting cylinder iii. 3 / 2 way valve iv. 3 / 2 way valve v. one way flow control valve vi. 5 / 2 way valve vii. 5 / 2 way valve viii. 5 / 2 way pneumatic actuated valve ix. 3 / 2 way roller lever valve x. shuttle valve ( or ) xi. two pressure valve ( and ) xii. pressure gauge xiii. manifold with self closing xiv. pushbutton station for electrical signal input xv. relay station xvi. 3 / 2 way single solenoid valve xvii. 5 / 2 way single solenoid valve xviii. 5 / 2 way double solenoid valve xix. power supply unit, xx. profile plate, anodised aluminium pneumatic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide carrier for mounting components, such as pb & relay boxes. cut section model for pneumatic components hydraulic trainer kit, each consisting of the following matching components and accessories i. hydraulic power pack ii. pressure relief valve iii. drip tray, steel iv. pressure gauge v. four way distributor vi. double acting hydraulic cylinder vii. suitable weight viii. mounting kit for weight ix. 3 / 2 way directional control valve x. 4 / 2 way directional control valve xi. 4 / 3 way directional control valve xii. non return valve. xiii. pilot operated check valve xiv. one way flow control valve xv. t connector with self sealing coupling nipples ( 2 nos. ) and quick coupling socket ( 1 no. ) . xvi. profile plate, hydraulic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide cut section models for hydraulic components total quantity : 818...
42295384 bids are invited for hammer ball peen 50 grams , wooden mallet small i s 2022 , surface plate 400 x400 mm grade i , v blocks with clamps , combination set 200 mm , scribing block, universal, 300 mm , tap and die set to cut b.s.f and b.s.w. and metric threads sizes no.6 to m 12 , screw pitch gauge to cover above threads , saw plumber 300mm , stove melting solder , snip straight 250mm , snip bend 250mm , tenon saw , hand saw. , mortise chisel , firmer chisel , mallet medium is 2922 , jack plane , gas welding set with oxygen acetylene cylinder , goggles pair welder 100 mm , brush steel wire 150x 50 mm , pliers combination, 200 mm , blow lamp 500 mililitre , scribing gauge , pot hook , branch gimlets , anvil 50 or 63 kg. is 510 , flat smithy tong , d.e. pedestal grinder with two wheels 175mm rough and smooth , bench drilling machine with chuck and key upto 15mm capacity , ring guage 15 mm, 20mm, 25mm, 32mm total quantity : 145...
36790488 bids are invited for hack saw tubular metal frame adjustable, anvil, electrical drill portable drill with chuck and key, sc total quantity : 592...
36745053 bids are invited for welding items h.p. welding torch , arc welding table , suitable gas welding table , oxygen, acetylene cylinders , co2 cylinder , leather apron leather , leather hand gloves , anvil 12 sq. inches working area with stand total quantity : 48...
36650528 bids are invited for boq boq pliers combination, , blow lamp , washer cutter , scribing gauge , soil pot with brush , pot hook , d e spanners , branch gimlets , bending spring , plumbers laddle , tool caulking of s , plumbers metal melting pot , pipe stock and dies complete with stocks, bushing, bushing holders, taps and wrenches sizes covered, to suit pipes , pipe vice , stillson pattern pipe wrenches , chain pipe wrench , adjustable, spanner, a375, is 6149 , anvil , pipe bender, manually operated , leg vice, 75mm jaw on stand is 2588 , hand drill 6mm capacity with drill chuck electric , drill twist straight shank , portable forge , , flat smithy tong , bath tub small size , water heater , urinal wall type complete with automatic system , water meter , hammering drilling machine , electric ppr pipe welding machine , electric pump, , de pedestal grinder with two wheels 175mm rough and smooth , hydraulic pressure machine for testing leakage in gi pipe fittings etc , rachet pipe die , bench drilling machine with chuck and key upto 15mm capacity , double face hammers , pipe bender manual type , ring guage total quantity : 1124...
36650151 bids are invited for boq boq radiator cut section cross flow , radiator cut section down flow , turbocharger cut sectional view , arbor press hand operated 2 ton capacity , discrete component trainer basic electronics trainer , hydraulic jack hi lift type 3 ton capacity, and 5 ton capacity , pipe bending machine hydraulic type , working condition of diesel engine crdi 6 stroke engine, assembly with fault simulation board , cut section of 4 or 6 cylinder diesel engine with moving condition to show momentum of internal parts , diesel engine six cylinder in running condition , air plasma cutting equipment , air compressor suitable for above air plasma cutting system. , portable gas cutting machine , pedestal grinder fitted with coarse and medium grain size grinding wheels , bench grinder fitted with fine grain size silicon carbide green grinding wheel , ag 4 grinder , suitable arc welding table , trolley for cylinder h.p. unit , hand shearing machine capacity , power saw machine , portable drilling machine , oven, electrode drying , mig welding machine with full accessories , oxy acetylene gas cutting blow pipe , oxygen, acetylene cylinders , co2 cylinder , argon gas cylinder , anvil 12 sq. inches working area with stand , swage block , portable abrasive cut off machine total quantity : 39...
36641102 bids are invited for radiator cut section cross flow , radiator cut section down flow , turbocharger cut sectional view , arbor press hand operated 2 ton capacity , discrete component trainer basic electronics trainer , hydraulic jack hi lift type 3 ton capacity, and 5 ton capacity , pipe bending machine hydraulic type , working condition of diesel engine crdi 6 stroke engine, assembly with fault simulation board , cut section of 4 or 6 cylinder diesel engine with moving condition to show momentum of internal parts , diesel engine six cylinder in running condition , air plasma cutting equipment , air compressor suitable for above air plasma cutting system. , portable gas cutting machine , pedestal grinder fitted with coarse and medium grain size grinding wheels , bench grinder fitted with fine grain size silicon carbide green grinding wheel , ag 4 grinder , suitable arc welding table , trolley for cylinder h.p. unit , hand shearing machine capacity , power saw machine , portable drilling machine , oven, electrode drying , mig welding machine with full accessories , oxy acetylene gas cutting blow pipe , oxygen, acetylene cylinders , co2 cylinder , argon gas cylinder , anvil 12 sq. inches working area with stand , swage block , portable abrasive cut off machine total quantity : 39...
36589139 bids are invited for plumber boq pkg 1 surface plate , v blocks with clamps , combination set , scribing block universal , hand vice jaw , file flat smooth , file half round rough , file square rough , file square smooth , file triangular rough , file flat rasp , file triangular smooth , chisel cold flat , chisel cross cut , chisel round nose , chisel diamond point , tap and die set to cut bsf threads , tap and die set to cut bsw threads , tap and die set to cut metric threads , screw pitch gauge to cover above threads , punch letter set , punch number set , spanner monkey up to , soldering iron copper bit fire heated hatched straight , snip straight , snip bend , try square , inside caliper , caliper outside , odd leg calliper , tenon saw , hand saw , mortise chisel , firmer chisel , mallet medium , jack plane , gas welding set , goggles pair welder , brush steel wire , table welding , pliers combination , blow lamp , scribing gauge , de spanners , branch gimlets , stillson pattern pipe wrenches , chain pipe wrench , anvil , pipe bender manually operated , leg vice 75mm jaw on stand , hand drill six mm capacity , drill twist straight shank , portable forge , flat smithy tong , hammering drilling machine , electric ppr pipe welding machine , de pedestal grinder with two wheels , bench drilling machine with chuck , double face hammers , ring guage total quantity : 102...
36566365 bids are invited for hack saw tubular metal frame, anvil, electrical drill portable, screw driver plastic handle, screw driv total quantity : 159...
36539421 bids are invited for tools for md trade anvil with stand , battery charger , blow lamp , clamps c , cleaning tray , cylinder liner dry and wet liner, press fit and slidefit liner , different type of engine bearing model , different type of piston model , fuel injection pump dismantling tool kit or universal vice , fuel injection pump ve pump or distributor fuel rotary pump dpc pumps along with special tools and accessories , radiator cut sectioncross flow , radiator cut section down flow , trammel , turbocharger cut sectional view , tyre pressure gauge with holding nipple , universal puller for removing pulleys, bearings , water pump for dismantling andassembling , arbor press hand operated 2 ton capacity , bench lever shears , discrete component trainer or basicelectronics trainer , drilling machine bench to drill up to12mm dia along with accessories , dual magnetization yoke , hydraulic jack hi lift type 3 toncapacity, and 5 ton capacity , liquid penetrate inspection kit , multi scan tool with oscilloscope , pipe bending machine hydraulic type , trolley type portable air compressor , welding transformer , v block 75 x 38 mm pair with clamps , vacuum gauge , valve lifter , auto electric test bench , pneumatic rivet gun with standard accessories , spring tension tester , tin smiths bench folder , welding plant oxy acetylene complete high pressure , air ratchet with standard accessories , air impact wrench with standard accessories , allen key set of 12 pieces , calliper inside with spring , callipers outside with spring , center punch. , dividers with spring , electrician screw driver , hammer ball peen with handle , dividers with spring , drift punch copper , drill point angle gauge , ammeter dc with external shunt , chisel flat total quantity : 111...
36539017 bids are invited for md trade items anvil with stand , battery charger , blow lamp , clamps c , cleaning tray , cylinder liner dry wet liner press fit slidefit liner , different type of engine bearing model , different type of piston model , fuel injection pump dismantling tool kit universal vice , fuel injection pump ve pump distributor fuel rotary pump dpc pumps along withspecial tools and accessories , radiator cut section cross flow , radiator cut sectiondown flow , trammel , turbocharger cut sectional view , tyre pressure gauge with holding nipple , universal puller for removing pulleys bearings , water pump for dismantling andassembling , arbor press hand operated 2 ton capacity , bench lever shears , discrete component trainer basic electronics trainer , drilling machine bench to drill up to 12 mm dia along with accessories , dual magnetization yoke , hydraulic jack hi lift type 3 ton capacity and 5 ton capacity , liquid penetrate inspection kit , multi scan tool with oscilloscope , pipe bending machine hydraulic type , trolley type portable air compressor , welding transformer , pneumatic rivet gun with standard accessories , spring tension tester , tin smiths bench folder , v block 75 x 38 mm pair with clamps , vacuum gauge , auto electical test bench , valve lifter , welding plant oxy acetylene complete high pressure , air ratchet with standard accessories , air impact wrench with standard accessories , car jet washer with standard accessories total quantity : 58...
36483464 bids are invited for supply of tools and equipments for mechanic diesel trade calliper inside with spring , callipers outside with spring , center punch. , dividers with spring , ammeter dc with external shunt , air ratchet with standard accessories , air impact wrench with standard accessories , anvil with stand , battery charger , cylinder liner dry and wet liner, press fit and slidefit liner , fuel injection pump dismantling tool kit or universal vice , fuel injection pump ve pump or distributor fuel rotary pump dpc pumps along with special tools and accessories total quantity : 51...
36479943 bids are invited for tool list marking table , pipe cutter wheel type , gas welding set with oxygen acetylene cylinder , table welding , washer cutter , caulking tool , plumbers metal melting pot 10 kg , pipe die and die stock with complete set , pipe vice , chain pipe wrench , anvil total quantity : 28...
36477288 bids are invited for supply of plumbing tools 1 58 rule steel , rule wooden 4 fold , hacksaw frame adjustable , scriber , centre punch , chisel cold, flat , hammer ball peen , file flat rough , level spirit wooden , plumb bob , trowel , stillson wrench , screw driver , wooden mallet small , cutting pliers 200mm , steel tape , surface plate , marking table , v blocks with clamps , combination set , scribing block, universal, , hand vice, jaw , file flat, smooth , file half round, rough , file, square, rough , file, square, smooth , file triangular rough , file flat rasp , file triangular smooth , chisel cold flat , chisel cross cut , chisel round nose , chisel diamond point , tap and die set to cut b.s.f. threads , tap and die set to cut b.s.w. threads , tap and die set to cut metric threads , screw pitch gauge to cover above threads , punch letter set , punch number set , saw plumber , spanner monkey up to , stove , oil stone , soldering iron , snip straight , snip bend , inside caliper , caliper outside , odd leg calliper , tenon saw , hand saw. , mortise chisel , firmer chisel , mallet medium , jack plane , brush steel wire , pliers combination, , blow lamp , washer cutter , mirror , scribing gauge , soil pot with brush , pot hook , branch gimlets , bending spring , plumbers laddle , tool caulking set of s , plumbers metal melting pot , pipe stock and dies , pipe vice , stillson pattern pipe wrenches , chain pipe wrench , adjustable spanner , anvil , pipe bender , leg vice , hand drill , drill twist , portable forge , , flat smithy tong , bath tub small size , wash basin equivalent metric , water heater , water meter , hammering drilling machine , electric pump , sight rail and bonning rod , rachet pipe die , double face hammers , ring guage total quantity : 546...
36476927 bids are invited for supply of tools and equipments anvil with stand , cleaning tray , cylinder liner dry and wet liner, press fit and slidefit liner , different type of engine bearing model , different type of piston model , split air conditioner , window air conditioner , radiator cut section cross flow , radiator cut section down flow , trammel , turbocharger cut sectional view , universal puller for removing pulleys, bearings , water pump for dismantling andassembling , piston ring compressor , piston ring expander and remover , piston ring groove cleaner , ring spanner set , torque wrench total quantity : 28...
36476681 bids are invited for boq boq welding helmet fiber , welding hand shield fiber , chipping hammer , chiesel cold , center punch , dividers , stainless steel rule , scriber , flat tongs , hacksaw frame , file half round , file flat , hammer ball pane , pipe cleaner , try square , universal weld measuring gauge , earth clamp , argon gas pressure regulator , flash back arrester torch , flash back arrester cyllinder , portable drill machine , oven electrode drying , anvil 12 sq inches working with stand , swage block , die penetrant testing kit , magnetic particle testing kit , portable abrasive cutoff machine total quantity : 181...
36461915 bids are invited for boq boq gauge , dowel pin straight , standard tap screws , lapping plate , medium carbon heat treated alloy steel metric studs and bolts along with nuts for display of standard length , caps screws , drill gauges , cast iron globe valve flanged type , c.i. sluice gate valve flanged type , stop cock , m.s. pipe , g.i. pipe , slip on forged steel flange , bolt and nut with washer may be manufactured in house , pipe threading die with handle , jigs and fixture sample for demonstration may be manufactured in house , pulleys for v belt or flat belt , steel keys may be manufactured in house , damaged old spur gear , v belt and flat belt , packing gasket , washer, clutch, keys, jib, cotter circlip , drill drift may be manufactured in house , bearing different types , lifting sling , bearing e xtractor , pulley e xtractor , trammel , pocker , prick punch , mallet. , aviation snips straight cut , flat headed hammers with handle. , planishing hammer. , snip bent left cut , stake hatchet with leg. , stake grooving. , slip gauge as johnson metric set. , gauge snap go and not go , gauge plug , gauge telescopic set. , dial test indicator on stand , sine bar , dial vernier caliper. universal type , screw thread micrometer with interchangeable. pitch anvils for checking metric threads 60. , digital vernier caliper. , digital micrometer outside. , comparators gauge dial indication with stand and bracket. , engineer s try square knife edge , surface roughness comparison plates , digital vernier caliper , vernier bevel protector , carbide wear block. , lathe tools h.s.s. tipped set. , lathe tools bit. , arm strong type tool bit holder. , stilson wrenches , pipe cutter wheel type. , d.e. pedestal grinding machine with wheels rough and smooth , neon tester , de soldering pump 2 93 total quantity : 881...
36445580 bids are invited for mechanic diesel trade items allen key set of 12 pieces , anvil with stand , battery charger , blow lamp , clamps c , cleaning tray , cylinder liner dry and wet liner, press fit and slidefit liner , fuel feed pump for diesel , fuel injection pump diesel inline , fuel injection pump dismantling tool kit or universal vice , fuel injection pump ve pump or distributor fuel rotary pump dpc pumps along with special tools and accessories , glow plug tester , hand shear universal , hand vice , hollow punch set of seven pieces , injector multi hole type, pintle type , injector cleaning unit , lifting jack screw , oil pump for dismantling and assembling. , portable electric drill machine , radiator cut section cross flow , radiator cut section down flow , surface gauge with dial test indicator plunger type , tandem master cylinder with booster , timing lighter , turbocharger cut sectional view , tyre pressure gauge with holding nipple , universal puller for removing pulleys, bearings , v block 75 x 38 mm pair with clamps , water pump for dismantling and assembling , arbor press hand operated 2 ton capacity , bench lever shears , diesel engine running condition stationary type , dual magnetization yoke , hydraulic jack hi lift type 3 ton capacity, and 5 ton capacity , liquid penetrate inspection kit , pipe bending machine hydraulic type , pneumatic rivet gun with standard accessories , trolley type portable air total quantity : 81...
36445157 bids are invited for tool and equipments compressor unit , pneumatic trainer kit , pneumatic workstation , carrier for mounting components , cut section model , hydraulic trainer kit , hydraulic workstation , cut section models , outside micrometer , welding helmet fiber , welding hand shield fiber , chipping hammer , dividers , stainless steel rule , hack saw frame , hammer ball pane , tip cleaner , try square , spot welding machine , auto darkening welding helmet , electrode holder , oxygen gas pressure , acetylene gas pressure , co2 gas pressure regulator , argon gas pressure regulator , oven electrode drying , oxy acetylene gas cutting blow pipe , anvil , swage block , die penetrant testing kit , magnetic particle testing kit , fire extinguishers , fire buckets with stand , portable abrasive cutoff machine total quantity : 383...
36444165 bids are invited for boq001 hand shearing machine capacity , portable drilling machine , oven electrode drying , oxy acetylene gas cutting blow pipe , oxygen acetylene cylinders , co2 cylinder , argon gas cylinder , anvil 12 sq inches working area with stand , swage block , magnetic particle testing kit , fire buckets with stand , portable abrasive cutoff machine , compressor unit , pneumatic trainer kit , i single acting cylinder , ii double acting cylinder , iii 3or2 way valve , iv 3or2 way valve , v one way flow control valve , vi 5or2 way valve , vii 5or2 way valve , viii 5or2 way pneumatic actuated valve , ix 3or2 way roller lever valve , x shuttle valve or , xi two pressure valve , xii pressure gauge , xiii manifold with self closing , xiv pushbutton station for electrical signal input , xv relay station , xvi 3or2 way single solenoid valve , xvii 5or2 way single solenoid valve , xviii 5or2 way double solenoid valve , xix power supply unit , xx profile plate anodised aluminium , pneumatic workstation total quantity : 297...
36437095 bids are invited for supply of small tools and equipments hammer ball peen with handle , measuring steel tape , combination plier insulated , screw driver insulated , allen key alloy steel , neon tester , heavy duty screw driver insulated , punch centre , spanner adjustable drop forged, ss , chisel firmer with wooden handle , hacksaw frame , try square , outside calliper , inside calliper , divider , pliers long nose insulated , pliers flat nose insulated , neon tester 500 v. , screw driver set , insulated combination pliers , tweezers , steel measuring tape , magneto spanner set , plier flat nose , steel rule with metric and british graduation , screw driver , chisel cold flat , safety goggles , dot punch , try square. , caliper inside spring type. , caliper hermaphrodite spring type , caliper outside spring type , divider spring type , scriber , centre punch , hammer ball peen with handle , hammer ball peen with handle. , steel rule , screw driver , outside spring caliper , inside spring caliper , hermaphrodite caliper , divider spring , hammer , cold chisel flat , safety glasses , steel tape , oil stone , calliper inside with spring , callipers outside with spring , center punch. , dividers with spring , ammeter dc with external shunt , air ratchet with standard accessories , air impact wrench with standard accessories , anvil with stand , battery charger , cylinder liner dry and wet liner, press fit and slide fit liner , fuel injection pump dismantling tool kit or universal vice , fuel injection pump ve pump or distributor fuel rotary pump dpc pumps along with special tools and accessories , injector multi hole type, pintle type , radiator cut section cross flow , radiator cut section down flow , turbocharger cut sectional view , vacuum gauge , water pump for dismantling and assembling , discrete component trainer or basic electronics trainer , trolley type portable air , welding helmet fiber , welding hand shield fiber , tip cleaner , number punch , letter punch , universal weld measuring gauge , flash back arrester torch mounted , flash back arrester cylinder mounted , gmaw welding machine , ac or dc gtaw welding machine , auto darkening welding helmet , portable gas cutting machine , bench grinder fitted with fine grain size silicon carbide green grinding wheel , ag 4 grinder , hand shearing machine capacity , portable drilling machine , oven, electrode drying , oxygen and acetylene cylinders , co2 cylinder , die penetrant testing kit , magnetic particle testing kit , portable abrasive cut off machine total quantity : 691...
36419404 bids are invited for welding spindle key , screw driver , number punch , letter punch , magnifying glass , universal weld measuring gauge , earth clamp , spanner de , c clamps , hammer sledge , ss tape , electrode holder , hp welding torch , oxygen gas pressure , acetylene gas pressure , co2 gas pressure regulator , argon gas pressure regulator , first aid box , flash back arrester , suitable gas welding table , suitable arc welding table , trolley for cylinder , hand shearing machine capacity , portable drilling machine , oven electrode drying , oxy acetylene gas cutting blow pipe , oxygen acetylene cylinders , co2 cylinder , argon gas cylinder , anvil , magnetic particle testing kit , portable abrasive cut off machine , suitable gas cutting table total quantity : 64...
36419350 bids are invited for welding spindle key , screw driver , number punch , letter punch , magnifying glass , universal weld measuring gauge , earth clamp , spanner de , c clamps , hammer sledge , ss tape , electrode holder , hp welding torch , oxygen gas pressure , acetylene gas pressure , co2 gas pressure regulator , argon gas pressure regulator , first aid box , flash back arrester , suitable gas welding table , suitable arc welding table , trolley for cylinder , hand shearing machine capacity , portable drilling machine , oven electrode drying , oxy acetylene gas cutting blow pipe , oxygen acetylene cylinders , co2 cylinder , argon gas cylinder , anvil , magnetic particle testing kit , portable abrasive cut off machine , suitable gas cutting table total quantity : 64...
36417826 bids are invited for tool and equipments compressor unit , pneumatic trainer kit , pneumatic workstation , carrier for mounting components , cut section model , hydraulic trainer kit , hydraulic workstation , cut section models , outside micrometer , welding helmet fiber , welding hand shield fiber , chipping hammer , dividers , stainless steel rule , hack saw frame , hammer ball pane , tip cleaner , try square , spot welding machine , auto darkening welding helmet , electrode holder , oxygen gas pressure , acetylene gas pressure , co2 gas pressure regulator , argon gas pressure regulator , oven electrode drying , oxy acetylene gas cutting blow pipe , anvil , swage block , die penetrant testing kit , magnetic particle testing kit , fire extinguishers , fire buckets with stand , portable abrasive cutoff machine total quantity : 383...
36412865 bids are invited for tools and equipement for fitter and plumber slip gauge as johnson metric , gauge snap go and t go , gauge plug , gauge telescopic , dial test indicator on stand , sine bar , dial vernier caliperuniversal type , screw thread micrometer with , depth micrometer 0 to 25 mm , digital vernier caliper , digital micrometer outside. , comparators gauge dial indication with , engineers try square knife edge , digital vernier caliper , vernier bevel protector , carbide wear block. , lathe tools h.s.s. tipped . , lathe tools bit. , arm strong type tool bit holder. , stilson wrenches or pipe wrerch , different profile gauges plate type for demonstration , knurling tool diamond, straight and diagonal , indexable boring bar with inserts , table welding , combination pliers , blow lamp , washer cutter , scribing gauge , soil pot with brush , pot hook , d. e. spanners is 2028 , branch gimlets , bending spring , plumbers ladle , caulking tool , plumbers metal melting pot 10 kg , pipe die and die stock with complete , pipe vice is 2587 , still son pattern pipe wrenches is , still son pattern pipe wrenches 300mm , chain pipe wrench , adjustable spanner is 6149 , anvil is 510 , leg vice is 2588 , hand drill machine , drill twist straight shank , smithy tong different shapes , water meter , black board with glass , fire extinguisher co2and dcp , fire buckets with stand , hammering drilling machine with drill bit total quantity : 148...
36395121 bids are invited for electronic mechanic 1 item 1 screwdriver 2 item 2 neon tester 3 item 3 screw driver set 4 item 4 insulated combination pliers 5 item 5 insulated side cutting pliers 6 item 6 digitalmultimeter 7 item 7 soldering iron changeable bits 8 item 8 desolderingpumpelectricalheated, manual operators 9 item 9 precision set of screw drivers 10 item 10 steel measuring tape 11 item 11 tools makers vice 12 item 12 tools maker vice 13 item 13 crimping tool ( pliers ) 14 item 14 magneto spanner set 15 item 15 plier flat nose 16 item 16 round nose pliers 17 item 17 scriber straight 18 item 18 tubular box spanner 19 item 19 magnifying lenses 20 item 20 continuity tester 21 item 21 chisel cold flat 22 item 22 scissors 23 item 23 hand drill machine electric withhammer action 24 item 24 first aid kit 25 item 25 dual dc regulated power supply 26 item 26 dc regulated variable programmable dc powersupply 27 item 27 lcr meter ( digital ) handheld 28 item 28 cro dual trace 29 item 29 signal generatorwith digital display for frequencyamplitude 30 item 30 battery charger 31 item 31 analog multimeter 32 item 32 clamp meter 33 item 33 function generator ( dds technology ( sine, square, triangle, ramp, pulse, serialdata, ttl and modulation. ) 34 item 34 dimmer starter 35 item 35 autotransformer 36 item 36 milli ammeter ( ac ) 37 item 37 milli ammeter ( dc ) 38 item 38 op amp trainer 39 item 39 digitalictrainer 40 item 40 digital ic tester 41 item 41 digital and analog bread board trainer 42 item 42 different types of electronic and electrical cables, connectors, sockets, terminations. 43 item 43 different types of analog electronic components, digital ics, power electronic components, general purposepcbs, bread board, mcb, elcb 44 item 44 dso ( colour ) 45 item 45 smd soldering & de soldering station with necessaryaccessories 46 item 46 dol starter 47 item 47 ac motor trainer kit¼ hp motor single phase contactors relaysmcbdol starter 48 item 48 frequency modulator and demodulator trainer kit 49 item 49 pam, ppm, pwm trainer kit 50 item 50 am / fm commercial radioreceivers 51 item 51 microcontroller kits ( 8051 ) along with programming software ( assembly level programming ) 52 item 52 application kits for microcontrollers 6 different applications 53 item 53 sensor trainer kit containing following sensors1. thermocouple2. rtd3. load cell / strain gauge4. lvdt5. smoke detector sensors6. speed sensor7. limit switch8. photo sensors9. optocouplor10. proximity sensor 54 item 54 fiber optic communication trainer 55 item 55 lcd tv ( trainer kit ) 56 item 56 home theatre system 57 item 57 solar training kit / simulator 58 item 58 led lighting system 59 item 59 fire extinguisher 60 item 60 fire buckets 61 item 61 welding helmet fiber 62 item 62 welding handshield fiber 63 item 63 chipping hammer 64 item 64 centre punch 65 item 65 dividers 66 item 66 stainless steel rule 67 item 67 scriber 68 item 68 flat tongs 69 item 69 hack saw frame 70 item 70 file flat 71 item 71 try square 72 item 72 number punch 73 item 73 letter punch 74 item 74 universal weld measuring gauge 75 item 75 earth clamp 76 item 76 hammer sledge 77 item 77 s.s tape 78 item 78 electrodeholder 79 item 79 h.p. welding torch 80 item 80 oxygen gas pressure 81 item 81 first aid box 82 item 82 steel lockers 83 item 83 auto darkeningwelding helmet 84 item 84 suitablegas welding table 85 item 85 suitablearc welding table 86 item 86 trolley for cylinder ( h.p. unit ) 87 item 87 power sawmachine 88 item 88 oven, electrode drying 89 item 89 work bench 90 item 90 oxy acetylene gas cutting blow pipe 91 item 91 oxygen, acetylene cylinders 92 item 92 co2 cylinder 93 item 93 anvil 12sq. inches working area with stand 94 item 94 swage block 95 item 95 die penetranttesting kit 96 item 96 magnetic particle testing kit 97 item 97 fire extinguishers ( foam type and co2 type ) 98 item 98 fire buckets with stand 99 item 99 suitable gas cutting table 100 item 100 allen key set of 12 pieces 101 item 101 calliper inside with spring 102 item 102 center punch. 103 item 103 electrician screw driver 104 item 104 hammer ball peen with handle 105 item 105 hands file forsecond cut flat 106 item 106 philips screw driver set of 5 pieces 107 item 107 screw driver blade 108 item 108 screw driver blade 109 item 109 scriber 110 item 110 spanner d.e. set of 12 pieces 111 item 111 spanner, ring set of 12 112 item 112 spanners socket with speed handle, t bar, ratchet and universal set of 28 pieces with box 113 item 113 steel rule 114 item 114 wire cutter and stripper 115 item 115 adjustable spanner ( pipe wrench ) 116 item 116 air blow gun with standard accessories 117 item 117 blow lamp 118 item 118 calliper inside with spring 119 item 119 callipers outside with spring 120 item 120 chain pulley block capacity with tripodstand 121 item 121 chisel flat 122 item 122 chisels cross cut 123 item 123 clamps c 124 item 124 compression testing gauge suitable fordiesel engine with standard accessories 125 item 125 connecting rod alignment fixture 126 item 126 cylinder bore gauge capacity 127 item 127 cylinder liner dry & wet liner, press fit &slidefit liner...
36390194 bids are invited for list of tools and euipments for fitter ictsm and em trade micrometer outside. , micrometer inside with extension rods. , vernier height gauges , vernier bevel protractor blade with acute angle attachment , screw pitch gauge metric , wire gauge, metric standard. , surface plate c.i , marking table mild steel , v block with clamps , angle plate , punch letter . , punch number . , portable hand drill electric , drill twist straight shank , drill twist taper shank , taps and dies complete in box. , taps and dies complete , file knife edge smooth , file feather edge smooth , file triangular smooth , file round second cut , file square second cut , feeler gauge , file triangular second cut. , file flat second cut safe edge. , file flat bastard , file flat bastard. , file swiss type needle , file half round second cut. , file half round bastard. , file round bastard. , file hand second cut. , file card or wire brush , oil can , wooden handle forged soldering iron copper bit. , blow lamp , spanner double ended , spanner adjustable , interchangeable ratchet socket , double ended tubular box spanner with tommy bar. , glass magnifying , clamp toolmaker , clamp c , hand reamer taper pin straight flute , machine reamer parallel helical flute , scraper flat , scraper triangular , scraper half round , chisel cold crosscut and diamond point. , chisel cold flat , chisel cold round se , drill chuck with key , pipe wrench , pipe vice , adjustable pipe die bsp , wheel dresser one for 4 units star or dresser with holder , machine vice swivel base , sleeve drill morse , fire buckets. , wing compass. , hand hammer with handle. , different profile gauges plate type for demonstration , knurling tool diamond, straight and diagonal , dowel pin straight , drill gauges , cast iron globe valve flanged type , c.i. sluice or gate valve flanged type , stop cock , m.s. pipe , g.i. pipe , slip on forged steel flange , pipe threading die with handle , jigs and fixture sample fordemonstration may be manufactured in house , pulleys 1 103fordemonstration may be manufactured in house , pulleys bid de fo ta r iv ls b e l t o r f la t belt , steel keys may be manufactured in house , damaged old spur gear , v belt and flat belt , packing gasket , washer, clutch, keys, jib, cotter and circlip , hollow punch , drill drift may be manufactured in house , bearing different types , lifting sling , bearing extractor , pulley extractor , trammel , pocker , prick punch , mallet. , aviation snips straight cut , flat headed hammers with handle. , planishing hammer. , snip bent left cut , stake hatchet with leg. , stake grooving. , slip gauge as johnson metric . , gauge snap go and t go , gauge plug , gauge telescopic . , dial test indicator on stand , sine bar , dial vernier caliper universal type , screw thread micrometer with interchangeable. pitch anvils for checking metric threads 60. , depth micrometer. 0 to 25 mm , digital vernier caliper. , digital micrometer outside. , comparators gauge dial indication with stand and bracket. , engineers try square knife edge , surface roughness comparison plates , digital vernier caliper , vernier bevel protector , compressor unit , pneumatic trainer kit consisting of the following matching components and accessories , single acting cylinder , double acting cylinder , 3 by2 way valve , 3 by 2 way valve , one way flow control valve , 5 by 2 way valve , 5 by 2 way valve , 5 by 2 way pneumatic actuated valve , 3 by 2 way roller lever valve , shuttle valve or , two pressure valve and , pressure gauge , manifold with self closing , pushbutton station for electrical signal input , relay station , 3 by 2 way single soleid valve , 5 by 2 way single soleid valve , 5 by 2way double solid valve , power supply unit , profile plate adised aluminium , pneumatic workstation with 40 square mm aluminium profile legs wooden work surface and one pedestal drawer unit having 5 drawers with handles and individual locks on metallic full panel drawer slide , carrier for mounting components, such as pb and relay boxes. , digital multimeter , soldering iron changeable bits , de soldering pump , crimping tool pliers , soldering iron , magneto spanner set , screw driver , steel rule , scriber straight , allen key set , tubular box spanner , magnifying lenses , continuity tester , soldering iron , power meter , crimping tools , computer toolkits , pen drives , external dvd writer total quantity : 368...
36365094 bids are invited for tools equipment hammer ball peen , file flat rough , level spirit wooden , plumb bob , trowel , stillson wrench , screw driver , wooden mallet small , cutting pliers 200mm , marking table , v blocks with clamps , combination set , scribing block universal , file flat smooth , file half round rough , file square rough , file square smooth , file triangular rough , file flat rasp , file triangular smooth , chisel cold flat , chisel cross cut , chisel round nose , chisel diamond point , tap and die set , screw pitch gauge to cover , spanner monkey up to , soldering iron , snip straight , snip bend , odd leg calliper , tenon saw , hand saw , mortise chisel , firmer chisel , mallet medium , jack plane , goggles pair welder , brush steel wire , table welding , stillson pattern pipe wrenches , chain pipe wrench , anvil , pipe bender manually operated , leg vice 75mm jaw , hand drill 6mm , drill twist straight shank , portable forge , flat smithy tong , working bench , hammering drilling machine , electric ppr pipe welding machine , electric pump , bench drilling machine , double face hammers , ring guage , allen key set of 12 pieces , center punch , dividers with spring , electrician screw driver , hammer ball peen with handle , hands file for second cut flat , philips screw driver set of 5 pieces , pliers combination , screw driver blade , scriber , spanner de set of 12 pieces , spanner ring set of 12 , spanners socket with speed , wire cutter and stripper , air blow gun with standard , ammeter dc with external shunt , air ratchet with standard accessories , air impact wrench , battery charger , dial gauge type 1 , dividers with spring , drift punch copper , drill point angle gauge , drill twist various sizes , tyre pressure gauge with holding nipple , vice grip pliers , water pump for dismantling , wire gauge metric , work bench , bench lever shears , multi scan tool with oscilloscope , pneumatic rivet gun with standard , 1 124with oscilloscope , pneumatic rivet gun with standard , bid de stp ariilnsg te n s io n tester , tin smiths bench folder , hand rubber gloves tested , hydrometer , safety glasses , welding helmet fiber , welding hand shield fiber , chipping hammer , chisel cold , centre punch , dividers , flat tongs , hack saw frame , file half round , file flat , hammer ball pane , try square , c clamps , hammer sledge , ss tape , electrode holder , hp welding torch , auto darkening welding helmet , bench grinder fitted with fine , ag 4 grinder , portable drilling machine , die penetrant testing kit , magnetic particle testing kit , screw driver insulated , heavy duty screw driver insulated , electrician screw driver thin , neon tester , hammer cross peen with handle , c clamp , pully puller with 3 legs , bearing puller inside and outside , pipe vice cast iron with , crimping tool , de metric spanner double ended , drill hand brace , plane cutters , smoothing cutters , gauge wire imperial stainlees , file round , file flat smooth , file rasp half round , copper bit soldering iron , table vice , brake test arrangement , laboratory type induction coil , out side micrometer , series test lamp , earth electrode , fuses , rheostat sliding type , safety belt , ohm meter series , ac voltmeter mi analog , milli voltmeter centre zero analog , ammeter mc analog portable , ac ammeter mi analog portable , kilo wattmeter analog , digital wattmeter , ac energy meter , power factor meter digital , frequency meter , magnetic flux meter , lux meter , tachometer , tong tester clamp meter , megger , 3 point dc starter , 4 point dc starter , wheat stone bridge with galvanometer , single phase variable autotransformer , growler , temperature controlled soldering station , discrete component trainer , linear ic trainer , digital ictrainer , voltage stabilizer , dc power supply , current transformer , potential transformer , solar panel with battery , connecting screwdriver , neon tester , screw driver set , insulated combination pliers , insulated side cutting pliers , long nose pliers , electrician knife , tweezers , crimping tool pliers , magneto spanner set , screw driver , scriber straight , allen key set , tubular box spanner , magnifying lenses , continuity tester , soldering iron total quantity : 1480...
36348570 bids are invited for tool and equipment vernier calliper , cut section of 4 6 cylinder diesel engine , automotive exhaust 5 gas analyser , working condition of diesel engine , leather hand gloves , cotton hand gloves , leather apron leather , ss wire brush , leather hand sleeves , safety boots for welders , leg guards leather , rubber hose clips , rubber hose oxygen , rubber hose acetylene , earth clamp , hp welding torch with 5 nozzles , oxygen gas pressure regulator double stage , acetylene gas pressure regulator double stage , co2 gas pressure regulator with flow meter , argon gas pressure regulator with flow meter , dc arc welding rectifiers set with all accessories , auto darkening welding helmet , oven electrode drying , oxy acetylene gas cutting blow pipe , anvil , die penetrant testing kit , portable abrasive cut off machine , file flat bastard , file half round bastard , file round bastard , scraper flat , scraper triangular , scraper half round , lathe tools , lathe tools bit , arm strong type tool bit holder , stilson wrenches , pipe cutter wheel type total quantity : 270...
36348283 bids are invited for hack saw tubular metal frame , anvil , electrical drill portable , screw driver plastic handle , screw driver plastic handle flat tip , soldering iron , tong tester , fire extinguisher , quick couples , welding table for gas arc , capillary plug gauge , piercing pliers , valve key handle , hollo punch hole for cutting gasket , spanner double ended , refrigerant cylinder , heating kit with infrared bulb , plumbing hammer weight , cylinder 134 a , torque wrench , piercing valve , feeler gauge , four way reversible valve , megger , k.w. meter , service oscillator , c.r.o single beam , cro dual trace , afo oscillators , service man thermometer , sling psychrometer , stop watch , tachometer digital , micron vacuum gauge , fin straightened fin comb , dial thermometer remote control , anemometer , compressors testers for small hermetic compressors , temperature humidity recorder , instrumentation screw driver set , digital weighing machine , ac 3 phase motor, 400 50 hz , star delta starter , dol starter , portable air lpg brazing kit , oxy acetylene weldingset complete , single door direct cool refrigerator , frost free refrigerator , three four door refrigerator , core drill machine , evacuating and charging station , two stagerotary vacuum pump , dry n2 cylinder , window ac , split ac , duct able split ac ton , recovery unit with cylinders , decibel meter , cassette air conditioner , de scaling pump set , fan coil unit , shell and tube dx hillers , circulating water pump , refrigerant cylinder , gauge manifold with gauges , shell and tube type condenser , rotary hermetic compressor , bottle cooler visible , deep freezer , display cabinet , water cooler storage type , water dispenser , ice candy plant , air conditioning direct system , air conditioning indirect system , package ac , car ac components , car ac tutorial model , bus ac tutorial model , automatic ice cube machine , storage type water cooler , vrf vrv unit with two indoor units , split a c inverter technology , walk in cooler puf , absorption system total quantity : 159...
36340867 bids are invited for standard boq mse angle plate , anvil with stand , oscilloscope total quantity : 4...
36340603 bids are invited for boq boq shunt , air ratchet with standard accessories , air impact wrench with standard accessories , angle plate adjustable , angle plate size , anvil with stand , auto electrical test bench , battery charger , car jet washer with standard accessories , chain pulley block capacity with tripod stand , clamps c , cleaning tray , copper bit soldering iron , drill point angle gauge , prick punch , punch letter 4mm number , right cut snips , rivet sets snap and dolly combined , scraper flat , scraper half round , scriber with scribing black universal , sheet metal gauge , tinnmansshear , soldering copper , spanner clyburn , spanner t. flocks for screwing up and up screwing inaccessible , spanner, adjustable , spanner, ring set of 12 metric sizes , spanners socket with speed handle, t bar, ratchet and universal , spark lighter , spark plug spanner 14mm x 18mm x size , steel measuring tape in a case , steel rule 15 cm inch and metric , steel rule 30 cm inch and metric , stud extractor set of 3 , stud remover with socket handle , surface gauge with dial test indicator plunger type , tachometer counting type , telescope gauge , temperature gauge with sensor , thermostat , thread pitch gauge metric , timing lighter , torque wrenches , trammel total quantity : 429...
36223086 bids are invited for welding helmet fiber , welding hand shield fiber , chipping hammer , chisel cold , centre punch , dividers , stainless steel rule , scriber , flat tongs , hack saw frame , file half round , file flat , hammer ball pane , tip cleaner , try square , spanner d.e. , c clamps , hammer sledge , s.s tape , h.p. welding torch , oxygen gas pressure , acetylene gas pressure , co2 gas pressure regulator , argon gas pressure regulator , first aid box , flash back arrester torch mounted , flash back arrester cylinder mounted , welding transformer , welding transformer or inverter based welding machine , d.c arc welding rectifiers set with all accessories , auto darkening welding helmet , spot welding machine , portable gas cutting machine , pedestal grinder fitted with coarse and medium grain size grinding wheels , bench grinder fitted with fine grain size silicon carbide green grinding wheel , ag 4 grinder , trolley for cylinder h.p. unit , hand shearing machine capacity , portable drilling machine , oxy acetylene gas cutting blow pipe , oxygen acetylene cylinders , co2 cylinder , argon gas cylinder , anvil 12 sq. inches working area with stand , swage block , welding process, inspection and codes dvd or cds. total quantity : 346...
36109253 bids are invited for tool and equipment air blow gun with standard accessories , ammeter dc with external shunt , air ratchet with standard accessories , air impact wrench , angle plate adjustable , angle plate size , anvil with stand , drill point angle gauge , drill twist various sizes , hand operated crimping tool , hand reamers adjustable , hand shear universal , pipe cutting tool , pipe flaring tool , rivet sets snap and dolly combined , scriber with scribing black universal , set of stock and dies metric , tinnmans shear , sheet metal gauge , stud extractor set of 3 , stud remover with socket handle , surface gauge with dial test indicator , torque wrenches , v block , machine vice swivel base , hexa blades , welder electrodes total quantity : 132...
36084034 bids are invited for tools equipment steel rule graduated both in metric and english unit , c clamp , spanner adjustable drop forged ss , blow lamp brass , chisel cold , chisel firmer with wooden handle , allen key alloy steel , grease gun , bradawl , pully puller with 3 legs , bearing puller inside and outside , scissors blade ss , mallet hard wood , hammer extractor type , hacksaw frame , outside calliper , inside calliper , divider , pliers round nose insulated , tweezers , snip straight and bent heavy duty , drill hand brace , drill ss twist block , plane cutters , smoothing cutters , gauge wire imperial stainlees steel , file flat , file half round , file round , file flat rough , file flat bastard , file flat smooth , file rasp half round , hydrometer , hand drill machine , portable electric drill machine , load bank , brake test arrangement , laboratory type induction coil , out side micrometer , thermometer digital , series test lamp , knife switch dpdt fitted with fuse , knife switch tpdt fitted , miniature breaker , earth plate , earth electrode , mccb , elcb and rccb , fuses , rheostat sliding type , ohm meter , kilo wattmeter analog , magnetic flux meter , lux meter , tachometer , tong tester clamp meter , megger , 3 point dc starter , 4 point dc starter , wheat stone bridge with galvanometer and battery , single phase variable auto , phase sequence indicator , growler , oscilloscope dual trace , function generator , temperature controlled soldering , discrete component trainer , linear ic trainer , digital ic trainer , dc power supply , battery charger , caliper inside spring type , caliper hermaphrodite spring type , caliper outside spring type , divider spring type , scriber , screw driver , chisel cold flat , hammer ball peen with handle , file flat second cut , file half round second cut , hacksaw frame fixed type , dot punch , vernier caliper , vernier height gauges , vernier bevel protractor blade with , screw pitch gauges , vernier bevel protractor blade with , screw pitch gauge metric , wire gauge metric standard , file knife edge smooth , file feather edge smooth , file triangular smooth , file round second cut , file square second cut , feeler gauge , file triangular second cut , file flat second cut safe edge , file swiss type needle , file half round bastard , file round bastard , file hand second cut , dual dc regulated power supply , dc regulated variable program , cro dual trace , signal generator with digital display , function generator , autotransformer , digital ic tester , digital and analog bread board trainer , soldering de soldering , smd soldering de soldering , lcd tv trainer kit , led tv trainer kit , led lighting system , allen key set of 12 pieces , calliper inside with spring , callipers outside with spring , center punch , dividers with spring , electrician screw driver , hands file for second cut flat , philips screw driver set of 5 pieces , pliers combination , screw driver blade , spanner de set of 12 pieces , spanner ring set of 12 , spanners socket with speed handle , steel rule , steel tool box with lock and key folding type , wire cutter and stripper , adjustable spanner pipe wrench , air blow gun with standard accessories , ammeter dc with external shunt , air ratchet with standard accessories , air impact wrench , angle plate adjustable , angle plate size , anvil with stand , auto electrical test bench , battery charger , blow lamp , belt tensioner gauge , welding helmet fiber , welding hand shield fiber , chipping hammer , chisel cold , centre punch , dividers , stainless steel rule , flat tongs , hack saw frame , hammer ball pane , tip cleaner , try square , spindle key , screw driver , number punch , letter punch , magnifying glass , universal weld measuring gauge , earth clamp , spanner de , c clamps , hammer sledge , ss tape , electrode holder , hp welding torch , inverter based welding machine...
36083698 bids are invited for workshop lab 1 machine shop planner machine heavy duty planner machine cap. 4’x 2.5’x2.5’ 1 planner machine with single tool post. complete with electrical accessories included with the above machine. 2hp 960 rpm, 3 phase electrical motor: 1 no. lathe machine ( norton type ) bed length 6 feet, light duty high precision all geared head lathe machine having norton gear box lead screw and feed shaft separate spindle, speed 60 1050 rpm with hardened bed and complete with all standard accessories such as driving plate, center adapter, dead center, change. 1 hand sheet cutting machine 12” cap. heavy duty cutter 4 bench vice 6 inch 18 hand vice 4 inch 10 pipe vice 3 inch 10 g clamp 6 inch 10 ball peen hammer, 800g 15 straight peen hammer, 1 kg 15 cross peen hammer, 800g 15 flat chisel 15 round nose chisel 15 solid frame hacksaw 25 adjustable frame hacksaw 25 10” flat files 15 10” square files 15 10” triangular file 15 scraper 8” 15 tap and die set ¼ to ½ 10 drill bits 1 / 8” to ½” 15 each hacksaw blade 150 tin cutter 15 steel rule 12” 30 try square 12” 30 scraper 6” 15 combination set 20 calipers 10” 15 divider 10” 15 v block 4” 15 2 carpenta ry shop surface planner machine size 18’ 1 length of table 68” width of table 18” height from floor to table 34” spindle size 4.5” wooden grinder machine 4 disc sander machine, 6” disc sander 5” 1 measuring tools four fold rule, wooden type 15 measuring tools steel tape, 3 meter 15 measuring tools try square 12”, stainless steel blade 15 measuring tools spirit level ( iron ) , 6” 15 cutting tool hand saw 16 inch 20 cutting tool tenon saw 10 inch 15 cutting tool firmer chisel 1 inch 15 cutting tool bevel chisel ½ inch 15 cutting tool mortise chisel ½ inch 15 cutting tool mortise chisel ¼ inch 15 planing tool iron jack plane 14 inch 10 boring tool drill but 1 / 16 inch to ½ inch ( 29 pc. set ) 4 striking tool claw hammer 340 gm 15 striking tool mallet hammer 15 striking tool ball pin hammer 800gm 15 holding tools bench vice no. 4 15 miscellaneous tools screw driver 200 mm blade 5 miscellaneous tools pincer 8 inch 15 miscellaneous tools scraper 6 inch 15 miscellaneous tools oil stone / sharpening stone 10 3 welding shop inverter based mig welding outfit inverter based gmaw welding outfit 1 inverter based digitally controlled gmaw outfit high efficiency and high power factorresulting energy saving enhanced reliability due to smd technology auto weld stop when welding torch is taken away from weld job compatible to power generator supply digital panel for adjusting the welding parameters 25% more energy efficient than conventional machines maximum power factor is 0.93 excellent dynamic response enables superior arc inverter based arc welding rectifier indigenous inverter based arc welding rectifier of current range 10 400amps, 3 ph, 415v, 50 hz. 1 three phase inverter based, high efficiency and high power factor dc welder suitable for long distance welding and cellulosic electrodes enhanced reliability due to smd technology capable of welding with all types of cellulosic electrodes including 6010, 7010g and 8010g high frequency igbt based rectifier arc force adjustment on panel. tig welding possible with external hf unit light weight, compact and portable for easy handling capable of welding with 100 meter + 100 meter welding and return cables gas welding with all accessories 1 welding helmet: auto darketing helmet 15 welding torch 15 welding regulator for oxygen, co2, acetylene 5 flash back arrestor 5 gas welding torch 5 gas heating torch 5 electrode holder 10 welding gloves 30 welding apron 30 leg guard 30 4 black smithy hand hammer, 800gm with handle 15 double ended sledge hammer of 2 kg head 15 tong 15 anvil 6 punch 15 chisel 15 flatter and set hammer 10 top & bottom swages with rod handle for top 10 top & bottom fuller with rod handle for top 10 heart tools...
36026840 bids are invited for boq boq pliers combination, , blow lamp , washer cutter , scribing gauge , soil pot with brush , pot hook , d e spanners , branch gimlets , bending spring , plumbers laddle , tool caulking of s , plumbers metal melting pot , pipe stock and dies complete with stocks, bushing, bushing holders, taps and wrenches sizes covered, to suit pipes , pipe vice , stillson pattern pipe wrenches , chain pipe wrench , adjustable, spanner, a375, is 6149 , anvil , pipe bender, manually operated , leg vice, 75mm jaw on stand is 2588 , hand drill 6mm capacity with drill chuck electric , drill twist straight shank , portable forge , , flat smithy tong , bath tub small size , water heater , urinal wall type complete with automatic system , water meter , hammering drilling machine , electric ppr pipe welding machine , electric pump, , de pedestal grinder with two wheels 175mm rough and smooth , hydraulic pressure machine for testing leakage in gi pipe fittings etc , sight rail and bonning rod , rachet pipe die , bench drilling machine with chuck and key upto 15mm capacity , double face hammers , pipe bender manual type , ring guage total quantity : 560...
36012496 bids are invited for tools and equipments allen key sets of 12 pieces , caliper inside with spring , caliper outside with spring , centre punch , dividers with spring , electrician screw drivers , hammer ball peen with handle , hands file for second cut flat , philips screw driver set of 5 pieces , pliers combination , screw driver blade , scriber , spanner de set of 12 pieces , spanner ring set of 12 , spanner socket with speed handle , steel rule , steel tool box with lock and key folding type , wire cutter and stripper , adjustable spanner pipe wrench , air blow gun with standard accessories , ammeter dc with external shunt , angle plate adjustable , angle plate size , anvil with stand , blow lamp , belt tensioner guage , calliper inside with spring , callipers outside with spring , car jet washer with standard accessories , chisel flat , chisels cross cut , circlip pliers expanding and contracting , clamp c , different type of engine bearing model , different type of piston model , feeler guage 20 blades metric , file flat bastard , file half round second cut , file square second cut , file triangular second cut , hacksaw frame , hand vice , oil can , prick punch , spark lighter , tachometer counting type , thread pitch guage metric , tyre pressure guage with holding nipple , valve lifter , vernier calliper , wire guage metric , dividers , stainless steel rule , tip cleaner , spindle key , screw driver , number punch , letter punch , spanner de , ss tape total quantity : 646...
36004553 bids are invited for tool and equipment allen key set of 12 pieces , calliper inside with spring , callipers outside with spring , dividers with spring , electrician screw driver , hammer ball peen with handle , hands file for second cut flat , philips screw driver set of 5 pieces , screw driver blade , spanner ring set of 12 , spanners socket with speed handle , steel rule , steel tool box with lock and key folding type , wire cutter and stripper , adjustable spanner pipe wrench , air blow gun with standard accessories , ammeter dc with external shunt , air ratchet with standard accessories , air impact wrench with standard accessories , anvil with stand , battery charger , blow lamp , chain pulley block capacity with tripod stand , chisel flat , chisels cross cut , copper bit soldering iron , file half round , second cut , file square second cut , file triangular second cut , flat file second cut , flat file bastard , fuel feed pump for diesel , fuel injection pump diesel inline , fuel injection pump dismantling tool kit universal vice , glow plug tester , grease gun , grease gun heavy duty trolley type , multimeter digital , radiator cut section cross flow , radiator cut section down flow total quantity : 177...
36004097 bids are invited for allen key set of 12 pieces , calliper inside with spring , callipers outside with spring , center punch. , dividers with spring , electrician screw driver , hammer ball peen with handle , hands file for second cut flat , pliers combination , screw driver blade 20 cm , screw driver blade 30 cm , scriber , steel rule , wire cutter and stripper , adjustable spanner pipe wrench , air blow gun with standard accessories , ammeter dc with external shunt , angle plate adjustable , angle plate size , anvil with stand , battery charger , blow lamp , calliper inside with spring , chain pulley block capacity with tripod stand , chisel flat , chisels cross cut , circlip pliers expanding and contracting , clamps c , cleaning tray , copper bit soldering iron , different type of engine bearing model , dividers with spring , drift punch copper , drill point angle gauge , drill twist various sizes , electric soldering iron , electric testing screw driver , engineers square , feeler gauge 20 blades metric , file flat , bastard , file, half round , second cut , file, square second cut , file, square round , file, triangular , second cut , files assorted sizes and types including safe edge file 20 nos , flat file second cut , flat file bastard , measuring steel tape , combination plier insulated , screw driver insulated 4 mm , screw driver insulated 6 mm , electrician screw driver thin stem insulated handle , heavy duty screw driver insulated , electrician screw driver thin stem insulated handle , punch centre , knife double bladed electrician , neon tester , steel rule graduated both in metric and english unit , hacksaw frame , try square , outside calliper , inside calliper , divider , pliers long nose insulated , pliers flat nose insulated , pliers round nose insulated , file flat , file half round , file round , file flat rough , file flat bastard , file flat smooth , file rasp, half round , de soldering gun , steel rule with metric and british graduation , try square. , caliper inside spring type. , caliper hermaphrodite spring type , caliper outside spring type , divider spring type , centre punch , screw driver , chisel cold flat , hammer ball peen with handle. , file flat second cut , file half round second cut , hacksaw frame fixed type , safety goggles. , dot punch , straight edge steel , spirit level metal type 2 , stud extractor ezy out , micrometer outside 0 to 25 mm , micrometer outside 25 to 50 mm , micrometer outside 50 to 75 mm , micrometer inside with extension rods. , vernier caliper , vernier bevel protractor blade with acute angle attachment , screw pitch gauge metric , wire gauge, metric standard. , punch letter set. , punch number set. , portable hand drill electric , file knife edge smooth , file feather edge smooth , file triangular smooth , file round second cut , file square second cut , feeler gauge , file triangular second cut. , file flat bastard. , file swiss type needle , pliers combination insulated , almirah total quantity : 784...
35964203 bids are invited for tools and equipments pincer, spanner adjustable drop forged ss 1 , magneto spanner set , tubular box spanner , spanner double ended , spanner adjustable , double ended tubular box spanner set with tommy bar , adjustable spanner , spanner , spanner clyburn , spanner de set of 12 piece , spanner t flocks for screwing up and up screwing inaccessible , spanner ring set of 12 metric sizes , spark plug spanner 14mm x 18mm x size , spanner de set of 12 pieces , spanner ring set of 12 , adjustable spanner pipe wrench , magneto spanner set with 8 spanners , blow lamp brass , blow lamp , allen key alloy steel , allen key set hexagonal set of 9 , allen key set , allen key set of 12 pieces , grease gun , bradawl , pully puller with 3 legs , scissors blade ss , scissors , mallet hard wood , mallet , hammer mallet , hammer extractor type , hammer ball pen , hammer ball peen with handle , hand hammer with handle , flat headed hammers with handle , planishing hammer , chipping hammer , hammer ball pane , hammer sledge , hammer ball peen , hammer chipping , hammer copper with handle , hammer plastic , hacksaw frame , hacksaw frame adjustable , hacksaw frame fixed type , hack saw frame , try square , engineers try square knife edge , try square , outside calliper , inside calliper , caliper inside spring type , caliper hermaphrodite spring type , caliper outside spring type , divider spring type , digital vernier caliper , calliper inside with spring , callipers outside with spring , dividers with spring , calliper inside with spring , divider , dividers , dividers with spring , welding helmet fiber , stainless steel rule , scriber , tip cleaner , spindle key , screw driver , number punch , letter punch , magnifying glass , earth clamp , ss tape , electrode holder , argon gas pressure regulator , auto darkening welding helmet , ag 4 grinder , oven electrode , oxy acetylene gas cutting blow pipe , anvil , swage block , die penetrant testing kit , magnetic particle testing kit , leather hand gloves , cotton hand gloves , ss wire brush , rubber hose clips , rubber hose oxygen , rubber hose acetylene , arc welding single coloured glasses , spark lighter total quantity : 1238...
35903692 bids are invited for boq boq steel rule with metric and british graduation , try square. , caliper inside spring type. , caliper hermaphrodite spring type , caliper outside spring type , divider spring type , scriber , centre punch , screw driver , chisel cold flat , hammer ball peen with handle , hammer ball peen with handle. , file flat second cut , file flat smooth , file half round second cut , hacksaw frame fixed type , safety goggles. , dot punch , steel rule graduated both in metric and english unit , straight edge steel , spirit level metal type 2 , stud extractor ezy out , combination set , micrometer outside. , micrometer inside with extension rods. , vernier caliper , vernier bevel protractor blade with acute angle attachment , screw pitch gauge metric , wire gauge, metric standard. , surface plate c.i , marking table mild steel , universal scribing block. , v block pair with clamps , angle plate , punch letter set. , punch number set. , portable hand drill electric , drill twist straight shank , drill twist taper shank , taps and dies complete set in box. , taps and dies complete set , file knife edge smooth , file feather edge smooth , file triangular smooth , file round second cut , file square second cut , feeler gauge , file triangular second cut. , file flat second cut safe edge. , file flat bastard , file flat bastard. , file swiss type needle , file half round second cut. , file half round bastard. , file round bastard. , file hand second cut. , file card , oil can , pliers combination insulated , wooden handle forged soldering iron copper bit. , blow lamp , spanner double ended , spanner adjustable , interchangeable ratchet socket set , double ended tubular box spanner set with tommy bar. , glass magnifying , clamp toolmaker , clamp c , hand reamer set taper pin straight flute , machine reamer parallel helical flute , scraper flat , scraper triangular , scraper half round , chisel cold crosscut and diamond point. 1 115scraper half round , chisel cold crosscut and diamond point. bid de , tc ah ilis se l c o ld r o und nose , drill chuck with key , pipe wrench , pipe vice , adjustable pipe die set bsp , wheel dresser one for 4 units staror dresser with holder , machine vice swivel base , sleeve drill morse , vice bench , bench working. , allen key set of 12 pieces , calliper inside with spring , callipers outside with spring , center punch. , dividers with spring , electrician screw driver , hands file for second cut flat , philips screw driver set of 5 pieces , pliers combination , screw driver blade , spanner d e set of 12 pieces , spanner, ring set of 12 , spanners socket with speed handle, t bar, ratchet and universal set of 28 pieces with box , steel rule , wire cutter and stripper , adjustable spanner pipe wrench , air blow gun with standard accessories , ammeter dc with external shunt , angle plate size , anvil with stand , auto electrical test bench , battery charger , calliper inside with spring , chisel flat , chisels cross cut , circlip pliers expanding and contracting , clamps c , cleaning tray , compression testing gauge suitable for diesel engine with standard accessories , copper bit soldering iron , cylinder bore gauge capacity , dc ohmmeter , depth micrometer , dial gauge type 1 gr. a complete with clamping devices and with magnetic stand , combination plier insulated , screwdriver insulated , heavy duty screwdriver insulated , knife double bladed electrician , neon tester , hammer, cross peen with handle , c clamp , spanner adjustable drop forged, ss , chisel cold , chisel firmer with wooden handle , allen key alloy steel , grease gun , pully puller with 3 legs , bearing puller inside and outside , pipe vice cast iron with hardened jaw open type , scissors blade ss , scissors blade, ss , crimpising tool , mallet hard wood , hammer extractor type , hacksaw frame , try square , divider , pliers long nose insulated , pliers flat nose insulated , pliers round nose insulated , snip straight and bent heavy duty , d.e. metric spanner double ended , drill s.s. twist block , plane cutters , smoothing cutters , gauge, wire imperial stainlees steel marked in swg and mm , welding helmet fiber , welding hand shield fiber , h.p. welding torch , pedestal grinder fitted with coarse and medium grain size grinding wheels , bench grinder fitted with fine grain size silicon carbide green grinding wheel , ag 4 grinder , trolley for cylinder h.p. unit , portable drilling machine total quantity : 1205...