East Central Railway - Bihar

46592665 supply of set of bracket complete of 30 ltrset of bracket complete of 30 ltr,set of bracket complete of 30 ltr watre tank as per planning set list .no. mplbkt wt 30 version 2, packing instruction pi042 version 1 [ warranty period: 30 months after the date of deli very ] ]...

Department Of Science And Technology - Bihar

46591849 supply of machines and laboratory equipments for civil engineering in the premises of government engineering college, kaimur 1. concrete maturity testing equipment 2. concrete resistivity meter 3. cement tensile testing machine 4. beam deflection apparatus 5. carbonation test apparatus 6. pupull out tester 7. spatula 8. core cutting machine with drill bit 9. blaine air permeability apparatus 10 weight 11 weight hanger 1 deval abrasion value deval machine: it consists of one or more (usually two) hollow cast iron cylinder having an internal diameter of 20 cm and depth 34 cm. the cylinders are closed at the bottom and provided with a tightly fitted cover. the cylinders are mounted on a shaft at an angle of 30 with the axis of rotation. is sieve of size 1.70 mm. abrasive charge 6 cast iron or steel balls each having an approximate diameter of 4.8 cm and weighing between 390 to 445 grams. balance of capacity 10 kg. drying oven tray. 1 2 specific gravity of bitumen by pycnometer method pycnometer wash bottle balance 1 3 bitumen striping test an oven to heat the aggregates a thermostatically controlled water bath. sieves of sizes 12.5mm and 20mm. beaker with a capacity of 500ml. a mixer for mixing the aggregate sample and bituminous binder. 1 4 1.70 mm is sieve (for los angel’s apparatus) brass frame (diameter 200 mm) without any joint with stainless steel mesh with mesh size 1.70 mm. 1 5 % of water content test of bitumen dean and stark apparatus, flask it is made up of heat resistant glass and its capacity is 500 ml. condenser it is made up of heat resistant glass, receiver, heater: gas burner or electric burner may be used, graduated cylinder of 100 ml capacity, solvent: petroleum or coal tar naphtha which is free from water. 1 6 pmc(pre mix carpet) seal coated sieve size 22.4mm, 11.2mm, 13.2mm, 5.6mm 1 7 water absorption test glass bekar (3) stirring glass rod (3) weight machine stop watch oven. 1 8 settlement test cylinder (500 m² glass cylinder) glass pipette balance (capable of weighting 1000g to 0.01g) beaker (two 100 ml glass or metal beaker) stir (glass or stain less steel with rounded ends.) oven (capable of maintaining a temperature of 163±30c) 1 9 sieve test for emulsion electronic balance acetone solvent (used for sieve wash) xylem solvent measuring jar container 600 micron sieve (dia. 100 mm) dish stop watch shallow dish 1 10 cement mixing test glass rod beaker electronic balance oven stopwatch 150 micron is sieve dish 1.4mm is sieve. 1 11 deleterious material test in aggregate beaker naoh solution & others reagent required sieve standard colour chart. 1 12 solubility test of bitumen gooch crucible glass fiber rubber tubing filter flask, filter tube rubber tubing stopper erlenmeyer flask, oven desiccator. 1 geotechnical engineering lab s.n. name of equipment specification 1 water bath 15 litre capacity, temperature controlled, led water bath 2 plate bearing test apparatus the plate bearing test is essentially a model test of foundations. it gives the load deformation characteristics for determining the ultimate bearing capacity of foundations. this test is a standard technique for determining bearing capacity of soils and the results of other methods are compared and calibrated with the values obtained with plate bearing test. in this method, a steel plate is subjected to a gradual increment of ksad and the corresponding settlement is noted. the ultimate bearing capacity is taken as the load at which the settlement increases at a rapid rate. hand operated hydraulic jack, capacity 500 kn. ino hydraulic hand operated pump ino high pressure flexible metallic pipe 5 m long 1 no ball and socket arrangement consisting of two steel plates, with one steel ball in between the plates. 1 no extension rod long. 12 min dia x 25 cm for taking dial gauge readings. 16nos magnetic base with female thread on top, for holding extension rod 4nos top end plate 50 mm dia with male thread, for fitting on to the extension rods and positioning the dial gauge plunger. 4nos column 15 cm dia x 25 cm long, with flanges, complete with four bolts and nuts. 2 nos column 15 cm dia x 50 cm long, with flanges, complete with four bolts and nuts ino datum bar lightweight, portable, total span 5m height approx. 30 cm, mounted on two removable legs. 2 nos anchor spikes 10nos quick release clamp for positioning dial gauge bracket i no dial gauge 25 mm travel, 001 mm least count 4nos load gauge 500kn i no ...

East Central Railway - Bihar

46565261 supply of rubber kit for mu2b valverubber kit for mu2b valve,rubber kit for mu2b valve , consist of 2 items. sr. no(1)o ring 15/16 inch od wabco pt no. 524614 qty/ kit 07. sr no. (2)gasket pipe bracket wabco pt no. 558987 qty/ kit 01. [ warranty period: 30 months after the date of delivery ] ] => limited...

Indian Oil Corporation Limited - Bihar

46556208 procurement of m/s ksb limited make spares , list of item(s) / work(s) as per tender documents , cvr,brg,pmp,p/n 360.01 02,ksb , slev,shft,pmp,p/n 523.12 , slev,shft,pmp,p/n 523.10 , pump comp. rotating assy, rphb 80 360/2 , slev,spacer,pmp,p/n 525.05 , ring,labyrinth,o.b.,pmp,p/n 423.01 , bracket,brg,o.b.,pmp,p/n 330.11 , bracket,brg,i.b.,pmp,p/n 330.12 , plate,diffuser,pmp,p/n 173 , comb gkt,rph ehm 250 630,p/n 411.10 , gaskets & o rings,rph 50 450...

Eastern Railways - Bihar

46542659 supply of tail lamp bracket etc.tail lamp bracket etc.,tail lamp bracket as per irs drg no. c/bf 1113, alt nil. [ warranty period: 30 m onths after the date of delivery ] [quantity tolerance (+/ ): 5 %age , item category : normal , total po value variation permitt ed: max 8 lacs ] ]...

Northeast Frontier Railway - Bihar

46509904 supply of 1.supply of kit for hand brake wheel comp 2.supply of safety loop for uncoupling rod 3.supply of brake cylinder piston pin for 4.supply of locking bracket for bp & fp.1.supply of kit for hand brake wheel comp 2.supply of safety loop for uncoupling rod 3.supply of brake cylinder piston pin for 4.supply of locking bracket for bp & fp.,supply of brake cylinder piston pin for boxn wagon. drawing no. rdsos drg. no. wd 8000 7 s 09, alt. 17, item no. 4 (part drg. no. w/pn 89). material and specification is:2062: 2011 (rev.7), amen d. no.1 of nov. 2012, gr. e250 a. [ warranty period: 30 months after the date of delivery ] ] , supply of safety loop for uncoupling rod. drawing no. rdso?s drg no. wd 03002 s 01, alt. 1. material and specification as per drawing. make/brand: self [ warranty period: 30 months after the d ate of delivery ] ] , supply of locking bracket for bp & fp. drawing no. rdsos drg. no. wd 10004 s 04 alt 00, i tem nos. 4 & 3. material and specification as per drawing. make swastika. [ warranty period: 30 month s after the date of delivery ] ] , supply of kit for hand brake wheel complete for boxn wagon consisting of 5 items. drawing no. rdsos drg. no. wd 80007 s 10, alt. 24. [ warranty period: 30 months after the date of delivery ] ] , supply of cylinders for co2 gas: is 7285 (part ii)2008. new empty industrial co2 cylinder 46. 7 ltrs water capacity with valve and guard. test certificate should be supplied while at the supply of the m aterial. [ warranty period: 30 months after the date of delivery ] ]...

Indian Oil Corporation Limited - Bihar

46443053 procurement of pump spares , list of item(s) / work(s) as per tender documents , shft,pmp,p/n 563 , intermediate shaft,cve 32 200,p/n 563.2 , head shaft,cve 32 200,p/n 563.3 , gasket,cve 32 200,p/n 810 , joint ring,cve 32 200,p/n 813 , o ring,pmp,p/n 823 , bearing bracket,kishor,p/n 701 , cplg,spigot,pmp,p/n 515 , bearing cover,kishor,p/n 741 , casing,p/n 100,model: cve 032x200 , i.b.housing,p/n 705, sl. no. 25388 89, , l.b. housing,p/n 706, sl. no. 25388 89 , stuffing box spacer,p/n:462,cve32x200 , upper cover,p/n 400,cve 032 200 , upper stool,p/n 752,sl. no. 25388 89 , lower stool,p/n 753, sl. no. 25388 89 , head shaft,cve 32 250,p/n 566.55 , intermediate shaft,cve 32 250,p/n566.53 , imp(full dia),25387/25386 (cve),kishore , impeller shaft,cve 32 250,p/n 566.51 , impeller sleeve,cve 32 250,p/n 511.50 , slev,head,pmp,p/n 513.50 , intermediate sleeve,cve 32 250,p/n 512.5 , w rings,case,25387/25386(cve),kishore , w rings,imp,25387/25386 (cve),kishore , gskt,pn 810,25387/25386 (cve),kishore , upper cover, p/n 400, astm a 216 gr.wcb , g. b. bush,p/n 508,25387/25386 (cve) , spigot coupling,515,25387/25386 (cve) , i.b. housing,p/n 706,25387/25386 (cve) , nut,imp,pn938,25387/25386(cve),kishore , stuffing box,p/n 725,25387/25386 (cve) , bearing cover,p/n 741,25387/25386 (cve) , bearing hsg p/n 701,model cve 32 250 , o ring,p/n 823,25387/25386 (cve),kishore...

Indian Oil Corporation Limited - Bihar

46431917 procurement of pump spares , list of item(s) / work(s) as per tender documents , wear ring,case,pmp,p/n 502.01,ksb , wear ring,imp,pmp,p/n 503.01,ksb , pressure ring p/n 454.01 , pressure ring, p/n 454.01 , shft,pmp,p/n 210 , slev,brg,pmp,p/n 529.06 , slev,interstg spacer,pmp,p/n 525.01 , ring,labyrinth,i.b.,pmp,p/n 423.02 , wear ring,case,pmp,p/n 502.01 , ring,split,pmp,p/n 501.11 , ring,split,pmp,p/n 501.12 , bush,throttle,pmp,p/n 542.06 , bush,neck,i.b.,pmp,p/n 456.02 , bush,neck,o.b.,pmp,p/n 456.01 , deflector,pmp,p/n 507.12 , stuffing box housing, p.no. 451.01 , stuffing box housing, p.no. 451.02 , cover, p.no. 160 , spacer slv,chtc 4/5,p/n 525.01 , spacer rng,chtc 4/5,p/n 504.01 , spacer rng,chtc 4/5,p/n 504.02 , spacer ring,chtc 4/5,p/n 504.03 , neck bush ,p/n: 456,chtcr 4/5,ksb , shaftp/n 210 , imp ring,rphb ecm 80 360/2,p/n 503.01 , imp.ring, rphb ecm 80 360/2,p/n 503.02 , shaft sleeve, rphb ecm 80 360/2,p/n 523. , barng sleeve, rphb ecm 80 360/2,p/n 529. , spcer sleve, rphb ecm 80 360/2,p/n 525.0 , labyrinth ring p/n 423.01 , labyrinth ring p/n 423.02 , wearing rings p/n 502.01 , wearing rings p/n 502.02 , spacer ring p/n 504 , spacer ring p/n 504.11 , split ring p/n 501 , gasket p/n 411.25 , gaskets p/n 400.01 , gskt,casing,pn 411.10,rphb hm 80 360/2 , gasket & o ring p/n 400 , throttle bush p/n 542.06 , neck bush(nde),rph ecm 80 360/2,p/n 456. , spacer sleeve p/n 525.04 , neck bush de p/n 456.02 , bearing bracket,p/n 330 , spacer sleeve pn 525.04, a276type410h , imp.wrg.ring(back)p.no 503.02 , impeller wear ring,p/n 503.01 , spacer ring pn 504.11, a276type410h&t , segmental ring, p/n 1501 , split ring pn 501,a276type316 , throat bush(de) pn 456.02,a276type410a , bearing guard(de)p.no. 423.01 , bearing guard(nde) p.no. 423.02 , bearing guard(de)p.no. 423.03 , impeller (stage),p/n:230 , bearing sleeve(pump shaft),p/n:529.01 , bearing sleeve(suc. diff.),p/n:529.02 , bering sleeve(drive sahft),p/n:529.04 , bering sleeve(inter. sahft),p/n:529.03 , stage sleeve,p/n:521 , wearing ring stage,p/n:502.02 , wearing ring suc,p/n:502.01 , split ring,p/n:501 , impellar ring stage,p/n:503.02 , impellar ring suc,p/n:503.01 , bearing bush(disc. casing),p/n:545.01 , bearing bush(suc. diff.),p/n:545.02 , bering bush(adapter),p/n:545.04 , bering bush(bering spider),p/n:545.03 , suction impeller,p/n:231 , o ring (1st stage),p/n:412.01 , o ring (adapter),p/n:412.03 , o ring (s.box),p/n:412.04 , o ring (stage),p/n:412.02...

Military Engineer Services - Bihar

46431432 tender for special repair to bldg no p 22 (smc) at af station bihta; 1 taking up or down 15 mm dia steel tubing and connections including cleaning for refixing or removal to storecomplete all as specified and as directed. 2 s&f 15 mm bore galvanised steel water tubing medium grade with necessary fittings as required and fixed to walls, ceiling or laid in floors etc complete all as specified and as directed. 3 s&f in repair 15mm borechromium plated fancy type stop valves , cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or union complete all as specified and as directed. 4 s&f in repair 15 mm borechromium plated concealed type angular stop valves, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or union complete all as specified and as directed. 5 s&f in repair of chromium plated 125 mm long shower rose with or without swivel joints including fixing to steel pipe or union complete all as specified and as directed. 6 s&f in repair of 15 mm bore chromium plated fancy type bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed. 7 s&f in repair of pvc connection 15 mm size with ptmt nuts of length 450 mm complete all as specified and as directed. 8 s&f in repair of soap dish stainless steel chromium plated decorative type approximate size 160mmx160mmx90mm complete all as specified and as directed. 9 s&f in repair brass chromium plated tubular towel rail, 20mm dia, d type, 60cm long between flanges fixed to wall complete all as specified and as directed. 10 s&f in repair vitreous china squatting pan orissa patternof size 580 mm x 440 mm, white with integral foot rests (excluding flushing cistern and flush pipe) including trap set in and including concrete and connection to flushing pipe including lime concrete bedding and connection to antisyphonage pipe etc and making good to floor complete all as specified and as directed. 11 s&f in repair vitreous china pedestal patternwash down water closet, white (excluding flushing cistern and flush pipe) including connection to drain (or out going pipe) and to flushing pipe, anti syphonage pipe, etc complete with plastic water closet seat cover, white, closed pattern with flat bottom and cover with mild steel chromium plated or aluminised hinging device complete all as specified and as directed. 12 s&f in repair10 litre capacity pvc low level cisternvalveless syphonic action type and pvc bend long type and connectin to flush pipe of any size and pattern with inlet ball valve float and handleincluding bracket completeall as specified and as directed. 13 s&f in repair vitreous china bowl type urinal,flat back of size 465mm x 355mm x 265 mm white (minimum), with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2including necessary connection complete all as specified and as directed. 14 s&f in repair 15mm bore pillar taps, fancy type, cast copper alloy chromium plated with capstan heads, decorative type screwed down, high pressure screwed for iron pipeand fixed complete all as specified and as directed. 15 s&f in repair 1200 mm x900 mm size looking mirror of selected quality glass mounted on 6 mm thick ac building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. 16 s&f in repair health faucet (abs body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 mlong flexible tube and abs wall hook including making connections and fixed in position complete all as specified and as directed.. 17 s&f sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm longcomplete all as specified and as directed. 18 s&f liquid soap container of ptmt fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 105 grams) complete all as specified and as directed. 19 s&f in repair 75mm pvc (swr) floor trap, plain with grating including jointing with solvent cement etc complete all as specified and as directed. 20 dismantling existing cast iron soil vent pipe upto 100 mm internal dia, fixed to wall laid in trenches incl all fitting & accessories complete all as specified and as directed. 21 s&f 100 mm dia sandcast iron soil waste and vent pipes in any length with or without ears laid in trenches or in floor with cement joints complete all as specified and as directed. 22 s&f 100 mm dia spun cast iron soil waste and vent pipesin any length with or without ears fixed to walls with cement joints complete all as specified and as directed. 23 s&f 75 mm dia spun cast iron soil waste and vent pipesin any length with or without ears laid in trenches or in floor with cement joints complete all as specified and as directed. 24 s & f 75 mm dia spun cast iron soil waste and vent pipesin any length with or without earsfixed to wall with cement joints complete all as specified and as directed. 25 s&f 100 mm bore cast iron bends of any radius diminshing pieces or tapers (larger bore measured) complete all as specified and as directed. 26 s&f 75 mm bore cast iron bends of any radius diminshing pieces or tapers (larger bore measured) complete all as specified and as directed. 27 s&f 100 mm borecast iron cowls complete all as specified and as directed. 28 s&f 75 mm borecast iron cowls complete all as specified and as directed. 29 taking down chowkats or frame with shutter (without taking out shutter from the frame) exceeding 1.50 sqm and not exceeding 4 sqm each and removing from site complete all as specified and as directed. 30 s&f for factory made solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet, reinforced with ms square tube fixed in opening complete as per manufacturers specifications complete all as specified and as directed. 31 s&f factory made solid pvc moulded door shutter , 28 to 30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded pvc sheet on the front face & 2 mm plain colour pvc sheet on back face, supplying andfixing in frame at site as pe specification and drawing, complete all as specified and as directed. 32 s&f factory made upvc door frame made of upvc, extruded sections having an overall dimension (exxtruded section profile) 42mm x 50mm (tolerance +1 mm), with wall thickness 2.0 mm(+ 0.2 mm), corners of the door frame jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. the hinge side vertical of the frames reinforced by galvanised mild steel tube of size 19mm x 19mm and 1mm (+ 0.1mm) wall thickness and 3 nos stainless steel hinges of suitable size fixed to the frame complete all as specified and as directed. 33 s&f factory made upvc white colour casement (openable) glazed door made of extruded profile with wall thickness of 2.3 mm (+0.2mm) . window profile with hollow section with multi chamber , frame (60mm x 58 mm), sash (60 x 78 mm). t profile (one vertical length in between two shutters) (60 mm x 74 mm). glazing bead ( 35 mm x 20 mm) will be mitred cut and fusion weldedat all corners. including drilling of holesfor fixing hardware and drainage of water etc. making arrangement for fixing of hardware. epdm gasket 1.2 +0.2mm thick galvanised steel frame (28 mm x 21.5 mm), sash (31 mm x 27 mm), t profile (27 mm x 17 mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners.[hardware: casement door handle made of zinc alloyed (white powder coated), corner striker, secondary strikers, cylinder, door transmission gear made of mild steel with multi point locking system with strikes, 3d hinges of zinc alloyed (white powder coated) and 5 mm thick glazing with selected quality glass complete all as specified and as directed.note: the unit rate quoted by contractor excludes cost of glass and includes all other conneted accessories. net opening will be measured for payment purpose. 34 s&f factory made upvc white colour casement (openable)wire mesh door made of extruded profile with wall thickness of 2.3 mm (+ 0.2mm) . window profile with hollow section with multi chamber , frame (60mm x 58 mm), sash (60 x 78 mm). t profile (one vertical length in between two shutters) (60 mm x 74 mm) including drilling of holesfor fixing hardware and drainage of water etc. making arrangement for fixing of hardware. epdm gasket 1.2 + 0.2mm thick galvanised steel frame (28 mm x 21.5 mm), sash (31 mm x 27 mm), t profile (27 mm x 17 mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners.[hardware: casement door handle made of zinc alloyed (white powder coated), corner striker, secondary strikers, cylinder, door transmission gear made of mild steel with multi point locking system with strikes, 3d hinges of zinc alloyed (white powder coated) andwire mesh of approved quality complete all as specified and as directed.note: the unit rate quoted by contractor excludes cost of wiremesh and includes all other conneted accessories. net opening will be measured for payment purpose. 35 s&f 100 mm size mild steel butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and as directed. 36 s&f 200 mm long aluminium anodized barrel tower bolt of extruded section, complete all as specified and as directed. 37 s&f 150 mm long aluminium anodized barrel tower bolt of extruded section, complete all as specified and as directed. 38 s&f150 mm extruded aluminium alloy handle, fabricated type omplete all as specified and as directed. 39 s&f floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall length of cover plate 140mm complete all as specified and as directed. 40 s&f aluminium extruded section body door closer hydraulically regulated designation no. 3, universal type, suitable for door shutter of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed, complete all as specified and as directed. 41 s&fstainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed. 42 s&f 4 mm thick figured glass, pin head type and glazing with oil putty in square exceeding 0.5 sqm each pane, complete all as specified and as directed. 43 dismantling wall and ceiling boards(fibre pulp insulation etc.) or insulations boards /slabs/blankets any thickness including aluminium / gi snap gridof any description complete all as specified and as directed. 44 s&f anodised powder coated gi snap grid frame work for false ceiling including perimeter channel and hanger 6mm dia gi (upto 1200 mm length) adjustinglevel fixed to roof slabby means of ceiling cleat made out of gi flat 40mmx3mm size 60 mm long and expansion hold fastners 12.5 mm dia 40 mm long complete all as specified and as directed. 45 s&f 12 mm thick gypsum board asin ceiling fixed with screw as per manufacturers instructions complete all as specified and as directed. 46 dismantling of brick work or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars, dressed stone work & precast concrete articles and removing rubbish from premises to a distance not exceeding50 m complete all as specified and as directed. 47 m&l brick work withold size flyash bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar1:6 complete all as specified and as directed. 48 m&l 15mm thick rendering in cement mortar1:6 on brick work or concrete surface as in wall, surface finished even and fair complete all as specified and as directed. 49 m&l reinforced cement concrete 1:2:4type b 1 (nominal mix)using 20mm gradedstone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and as directed. 50 use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc rough finished surfaces of concrete complete all as specified and as directed. 51 m&l mild steel tmt bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 52 m&l mild steel tmt bars 6 mm dia and over as in stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 53 taking down cement plaster on brick or stone walls & chajja including raking out joint, hacking for key,scrubbing downwith water complete all as specified and as directed. 54 m&l 5mm thick rendering in cement mortar1:3 on concrete surface as in ceiling, surface finished even and fair complete all as specified and as directed. 55 m&l 15mm thick rendering in cement mortar1:4 on brick work or concrete surface as in wall mixed with water proofing compound as per manufacturers instruction, surface finished even and fair complete all as specified and as directed.note: water proofing compound shall be measured and paid seperately. 56 supply only integral water proofing compound complete all as specified and as directed. 57 m&l forapplying two coats of acrylic smooth exterior paint (100% acrylic) applied @ 1.67 litre/10sqm over and including priming coat of exterior primer (acrylic base) applied @ 2.20 kg/10sqmof approved shade including preparation of newly plastered surfaces of walls, chajjas, columns, beams etc complete all as specified and as directed. 58 m&l forapplying two coats of acrylic smooth exterior paint (100% acrylic) applied @ 1.67 litre/10sqm over and including priming coat of exterior primer (acrylic base) applied @ 2.20 kg/10sqmof approved shade including complete removal of existing treatment and preparation of old decorated surfaces of walls, chajjas, columns, beams etc complete all as specified and as directed. 59 m&l for applying three coats of white wash including preparation of newlyplastered surfaces of ceilingcomplete all as specified and as directed. 60 m&l for applying two coats of white wash including preparation of old surfaces of ceilingcomplete all as specified and as directed. 61 m&l applying two coats oil bound distemper of approved shade over a coat of alkali resistant primer over and including 1 mmthick wall care putty including preperation of newly plastered surfaces of wallcomplete all as specified and as directed. . 62 m&l applying two coats oil bound distemper of approved shade over a coat of alkali resistant primer over and including 1 mmthick wall care putty including complete removal of existing treatment and preperation of old decorated surfaces of wallcomplete all as specified and as directed. . 63 m&l forapplying three coats of white wash includingpreparation of newlyplastered surfaces of wallcomplete all as specified and as directed. 64 m&l for applying two coat of white wash includingpreparation of old decorated plasteredsurfaces of wall omplete all as specified and as directed. 65 demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed. 66 m&l for 25 mm thick cement concrete 1:2:4 type b 0 using 12.5 mm gradedstone aggregate as on floor, surface finished even and fair complete all as specified and as directed. 67 m&l for 18 to 20 mm thickprepolished mirror finished machine cut kota stone slab laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 including rubbing and polishingcomplete all as specified and as directed. 68 m&l for 16 to 18 mm thick prepolished mirror finishedmachine cut kota stone slab flooringas in riser of steps,skirting,dado and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the slabover 10 mm thick rendering in cement mortar 1:4 including rubbing and polishing complete all as specified and as directed. 69 m&l for 7 to 8 mm thick coloured non skidceramic tiles(square/ rectagular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc setand jointed in neat cement slurry and pointed in white or coloured cement to match over andincluding 15 mmthick screed bed or beddinglayer in cement mortar 1:6, surface finished even and roughcomplete all as specified and as directed. 70 dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. 71 demoliton of stone slabs and tiles of any description or thickness in floors, apron, platform etc laid, bedded and pointed in any mortar complete all as specified and as directed. 72 rounding to edges of stone slabs one edge, such as in steps, cooking platform, and similar situations complete all as specified and as directed. 73 m&l for 6 to 7 mm thick glazed ceramic coloured tiles in vertical surface of size350mmx250mm or 450mmx 350 mm, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and inclduing 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed. 74 m&l for 7 to 8 mm thick coloured non skidceramic tiles(square/ rectagular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc setand jointed in neat cement slurry and pointed in white or coloured cement to match over andincluding 15 mmthick screed bed or beddinglayer in cement mortar 1:6, surface finished even and roughcomplete all as specified and as directed. 75 s&f 25mm thick harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and as directed. 76 s&f in repair vitreous china wash hand basin, white, flat back of size 550mm x 400 mm including waste coupling, cast iron brackets, pvc waste pipe32 mm boreincluding necessary connection complete all as specified and as directed. 77 taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking creditincluding making good disturbed surfaces of walls, floors etc to match with the existing complete all as specified and as directed. 78 m&l point wiring with single corefrlsh pvc sheathedmulti stranded copper conductor of size 1.5 sqmm drawn through and including non metallic rigid pvc conduit medium grade isi markednot less than 20mm dia with gi saddles gi screws, rawl plugs (concealed conduit wiring in walls and casing capping on ceiling or roof ) including tee, junction boxes and provision of3 mm thick plastic laminated sheet cover of suitable size ,mild steel terminal boxmade out of 1.6mm thick mild steel sheet with brass screwsfor mounting modular switchs, sockets,regulators etc including 1.5 sqmm frlsh pvc sheathedstrandedcopper conductor cable as continuous earth wire and connected to main earth dolly complete all as specified and directedfor one light/fan/exhaust fan point/ bell point controlled by one switch 79 description same as peritem no 78 above but for 3 pin 5 amps socket outlet on independent boardcomplete all as specified and as directed. 80 description same as peritem no78 above but for 3 pin 5 amp socket outlet on same board with other switches complete all as specified and as directed. 81 description same as peritem no78 above but for one bell/buzzer point controlled by one bell push switch complete all as specified and as directed. 82 description same as peritem no 78 above but for one power point 3/5 pin 15 amps socket out letindependent board using 2.5 sqmm multi stranded frlsh pvc insulated copper conductor cablewith 2.5 sqmm multi stranded frlsh pvc insulated copper conductor cable as earth wire complete all as specified and as directed. 83 s&f modular switch 1 way, 6a,1 module complete all as specified and as directed. 84 s&f modular sockets 6 a, 2/3 pin ,2 module complete all as specified and as directed. 85 s&f modular switch 1 way, 16a,1 module complete all as specified and as directed. 86 s&f modular sockets 6a/16 a , 2/3 pincombined, 2 module complete all as specified and as directed. 87 s&f ceiling rose surface bakelite 60mmx25mm three terminal 240 vcomplete all as specified and as directed. 88 s&f modular bell push flush type 6 a, 240 v complete all as directed. 89 s&fbell ,ac, 230 v, single pole complete all as specified and as directed. 90 s&f led lights fitting 1x 20w, 220v, ac decorative box type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rosecomplete all as specified and as directed. 91 s&f led luminaire 600 mm x 600 mm, 35/36 watt, 220 v, ac recessed type with high efficiency pmma diffuser soft glare free light complete with driver, holders and led lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed. 92 s&f in replacement ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 v, 1200 mm sweep. min air delivery 210 cfm with service value 6.00 bee. five star rated with brushless direct current motor (bldc)complete all as specified and as directed.note : old unserviceable ceiling fans shall be deposited in messtore yard. 93 m&lfor hanging ceiling fanand connecting up including provision of cable from ceiling rose or connector to fan including applying one coat of synthetic enamel paint of approved shade including preperation of surfacesincluding filling cavitiesand taking down existing ceiling fan complete all as specified and as directed. 94 s&f mcb ,sp, 6 32 amps, c series, 240 v complete including making connections complete all as specified and as directed. 95 s&f mcb ,double pole, 40 63 amps, c series, 240 v complete including making connections complete all as specified and as directed. 96 s&fsheet metal enclosuredouble door, single pole and neutral 8way with 200 amp rated bus bar, 240 v, flush to wall including all cutting etc on wall and making good the disturbed surfaces to match the existing including taking out oldunserviceable db box complete all as specified and directed. 97 s&f 63 amp mcb, 415v, 10ka b curve,4 pole including necessary connection complete all as specified and as directed. 98 s&fsheet metal enclosuredouble door, triple pole and neutral 8 way with 200 amp rated bus bar, 240 v, flush to wall including all cutting etc on wall and making good the disturbed surfaces to match the existing including taking out oldunserviceable db box complete all as specified and directed. 99 s&f submain wiring with twosingle core 4 sqmmfrlsh pvc insulatedmultistrand copper conductor cable drawn in andincludingconcealed rigid non metallic pvc conduit dia not less than 20 mm , medium gradeisi marked with all fittings and fixing accessories and one single core 4 sqmmfrlsh pvc insulated multistrand copper conductor cable as continuous earth wire complete all as specified and as directed.note: two run of 4 sq mm copper cable,one run of pvc conduitand one run of 4 sq mm copper cable earth wire shall be measured as one unit. 100 s&f submain wiring with twosingle core 6 sqmmfrlsh pvc insulatedmultistrand copper conductor cable drawn in andincludingconcealed rigid non metallic pvc conduit dia not less than 20 mm , medium gradeisi marked with all fittings and fixing accessories and one single core 6sqmmfrlsh pvc insulated multistrand copper conductor cable as continuous earth wire complete all as specified and as directed.note: two run of 6 sq mm copper cable,one run of pvc conduitand one run of 6 sq mm copper cable earth wire shall be measured as one unit. 101 s&f sheet metal enclosure with socket and plug top and mcb single pole and neutral enclosure with two pin and earth plug and socketwith one single pole mcb,20 amp,240 v complete all as specified and as directed. 102 m&l for taking downexisitngair conditioning indoor and outdoor unit with stand copper tubing or air curtain carefully with refrigerant and refixing the same afterrepair work and testingcomplete all as specified and directed. 103 s&fled street light fitting 35 watt230 v, ac outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with ip 65/66 protection complete all as specified and as directed. 104 m&l earthing complete with galvanised steel earth plate electrode 600mmx600mmx6mm thick, buried directlyin ground(earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanisediron strip 25mmx4mm (upto 7.5 m in length from earth plate) by means of bolts, nuts, check nuts and washers of galvanisediron or steel ,filling adequate quantity of charcoldust and common salt all as shown in electrical plate no 3 of ssr part 2009, connected to earthing with dbs all as specified including excavation and earth work in any type of soil, pcc 1:3:6 type c 1 using 20mm graded stone aggregate in chamber &cast iron earthingpit cover having size 250mmx250 mm, weight not less than 7.5 kg as per relevant isincluding frame, 40 mm dia gi pipe light grade for earth lead protection, 20mm dia gi medium grade pipe for watering , water funnel etc complete all as specified and testing on completion. 105 supply, laying, jointing and testing xlpe cable insulated, armoured, earthed, heavy duty electric cable with aluminium conductor , 1100 volt grade, cross sectional area 35 sqmm 3.5 core including necessary cable lugs, glands, insulation tape etc complete all as specified and as directed.make: finolex/ gloster/ polycab 106 supply, laying, jointing and testing xlpe cable insulated, armoured, earthed, heavy duty electric cable with aluminium conductor , 1100 volt grade, cross sectional area 10 sqmm 2 core including necessary cable lugs, glands, insulation tape etc complete all as specified and as directed.make: finolex/ gloster/ polycab 107 excavation in trenches , not exceeding 1.5 m wide and not exceeding 1.5 m in depthfor founddationetc and getting out in soft/loose soil complete all as specified and as directed. 108 returning, filling in, including spreading levelling watering and well ramming in layers not exceeding 25 cmas in soft/loose soil complete all as specified and as directed. 109 removing excavated soilto a distancenot exceeding 50 manddepositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed. 110 supply and laying old size bricks of designation 75 for cable protection complete all as specified and as directed. 111 m&l for natural river sand as cushioning of cables including spreading and punning downcomplete all as specified and as directed.note : punned thickness shall be measured for payment purpose 112 m&l 50 mm bore galvanised iron pipe light grade as in protection to cable laid in trench or in floor or fixed to wall with necessary fittings complete all as specified and as directed.. 113 m&l 25 mm bore galvanised iron pipe medium gradelaid in trench or in floorwith necessary fittings including taking out existing pipe complete all as specified and as directed.. 114 m&l 25 mm bore gun metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.. ...

East Central Railway - Bihar

46365733 supply of poh kit for common pipe bracket of m/s knorr bremse india l.td make consisting of six items: 1) sealing ring to kbi p no kd 05.qty/set i no. 2)o ring to kbi pt no kd 182.qty/set i no. 3)o ring to kbi p no kd 86, qty/set 2 nos. 4) filter to kbi pt no kd |91,0ty/set i no. 5)seal to kbi pt no kd 192,qty/set | no. 6) seal to kbi p no kd 196,qty/set l nopoh kit for common pipe bracket of m/s knorr bremse india l.td make consisting of six items: 1) sealing ring to kbi p no kd 05.qty/set i no. 2)o ring to kbi pt no kd 182.qty/set i no. 3)o ring to kbi p no kd 86, qty/set 2 nos. 4) filter to kbi pt no kd |91,0ty/set i no. 5)seal to kbi pt no kd 192,qty/set | no. 6) seal to kbi p no kd 196,qty/set l no,poh kit for common pipe bracket of m/s knorr bremse india l.td make consisting of six items: 1) sealing ring to kbi p no kd 05.qty/set i no. 2)o ring to kbi pt no kd 182.qty/set i no. 3)o r ing to kbi p no kd 86, qty/set 2 nos. 4) filter to kbi pt no kd |91,0ty/set i no. 5)seal to kbi pt no kd 192,qty/set | no. 6) seal to kbi p no kd 196,qty/set l no [ warranty period: 30 months after the dat e of delivery ] ]...

Northeast Frontier Railway - Bihar

46362719 supply of different types of item for maintenance of wagons at roh depot/njpdifferent types of item for maintenance of wagons at roh depot/njp,supply of jubilee clamp dia. 130 for escorts design bmbs. escorts drg. no. 4eb8935. mate rial and specification as per operation and maintenance manual of escorts make bmbs for freight stock wi th casnub bogie; doc. no. red rd bs 019 om 01; rdso?s spec. no. wd 23 bmbs 2008 (rev. 1) amendme nt no.1 of sept.,2016. make escorts kubota limited. [ warranty period: 30 months after the date of deliv ery ] ] , supply of bellow for escorts design bmbs. drawing no. escorts drg. no. 3eb7517 material and specification as per operation and maintenance manual of escorts make bmbs for freight stock with c asnub bogie; doc. no. red rd bs 019 om 01; rdso?s spec no. wd 23 bmbs 2008 (rev. 1) amendment n o.1 of sept 2016. [ warranty period: 30 months after the date of delivery ] ] , supply of split pin 5x32 for escorts design bmbs. drawing no. escorts drg. no. is 549/eq v material and specification as per operation and maintenance manual of escorts make bmbs for freight s tock with casnub bogie; doc. no. red rd bs 019 om 01; rdso?s spec no. wd 23 bmbs 2008 (rev. 1) am endment no.1 of sept 2016 make/brand escorts kubota limited. [ warranty period: 30 months after the date of delivery ] ] , supply of bc chain holding bracket escorts drg. no. 3eb10268 or latest as per operation and maintenance manual of escorts make bmbs for freight stock with casnub bogie; doc. no. red rd bs 019 om 01; rdso spec no wd 23 bmbs rev 01 amendment no.1 of sept 2016, make escorts kubota ltd. [ w arranty period: 30 months after the date of delivery ] ] , supply of pin for cable for escorts design bmbs. drawing no.: escorts drg. no. 4eb5567. material and specification as per operation and maintenance manual of escorts make bmbs for freight sto ck with casnub bogie; doc. no. red rd bs 019 om 01; rdso?s spec no. wd 23 bmbs 2008 (rev. 1) ame ndment no.1 of sept 2...

Eastern Railways - Bihar

46362701 supply of truck brake lever bracket assemblytruck brake lever bracket assembly,truck brake lever bracket assembly as per emd pt.no.40077221 and dlw pt.no. 17 020451 alt c [ warranty period: 30 months after the date of delivery ] ]...

Eastern Railways - Bihar

46356293 supply of board assembly terminalboard assembly terminal,board assembly terminal alternator 12 point includes bracket emd part no.8422220,drg.no.8422220. [ warranty period: 30 months after the date of delivery ] ]...

Ministry Of Power - Bihar

46354913 bids are invited for 00010 m1878219606 vv,btfl: wfr,bs en 593+,pn10,300mm,man no 20.000 16.02.2025 00020 m1878219605 vv,btfl: wfr,bs en 593+,pn10,200mm,man no 10.000 16.02.2025 00030 m1878519604 vv,btfl: wfr,en593+,ci,pn10,150mm,pne u no 24.000 16.02.2025 00040 m1878270766 vv,btfl: wfr,en593+,fg260,pn 10,350mm no 10.000 16.02.2025 00050 m1878270552 vv,btfl: wfr,ci,fg200,pn10,150mm,man no 4.000 16.02.2025 00060 m1878570710 vv,btfl: wfr,en593+,ci,pn10,100mm,pne u no 12.000 16.02.2025 00070 m1878170958 vv,btfl: wfr,en593+,ci,pn10,250mm,man no 4.000 16.02.2025 00080 m1878219608 vv,btfl: wfr,bs en 593+,pn10,400mm,man no 10.000 16.02.2025 00090 m1878170776 vv,btfl: wfr,bs en 593+,pn10,450mm,man no 2.000 16.02.2025 00100 m1878900257 vv,btfl: bs5155,flg,sgi,pn6,150mm,pne u valve,butterfly type : wafer design spec : is 13095/bs 5155/api 609/bs en 593 material,body : cast iron material spec,body : ci is 210 fg 260 material,trim : shaft ss 410 disc sgi en1563 en gjs 400 15 bore : 300 mm pressure designation : pn 10 nominal size : 300 mm additional information : manual worm gear box operated bi directional flow with manual worm gear box valve should be suitable to mount between ansi b16.5 cl150 flanges. 00020 m1878219605 specification valve,butterfly type : wafer design spec : is 13095/bs 5155/api 609/bs en 593 material,body : cast iron material spec,body : ci is 210 fg 260 material,trim : shaft ss 410 disc sgi en1563 en gjs 400 15 bore : 200 mm pressure designation : pn 10 nominal size : 200 mm additional information : manual worm gear box operated bi directional flow with worm gear box and handwheel valve should be suitable to mount between ansi b16.5 cl150 flanges. 00030 m1878519604 specification valve,butterfly type : wafer design spec : is 13095/bs 5155/api 609/bs en 593 material,body : cast iron material spec,body : ci is 210 fg 260 material,trim : shaft ss 410 disc sgi en1563 en gjs 400 15 bore : 150 mm pressure designation : pn 10 nominal size : 150 mm additional information : pneumatic operated with pneumatic power actuator and accessories, operating pressure:air 5ksc valve should be suitable to mount between ansi b16.5 cl150 flanges. 00040 m1878270766 specification valve,butterfly page 3 of 11 ntpc limited ( a government of india enterprise ) tender enquiry no. 9900290461 type : wafer design spec : is 13095/bs 5155/api 609/bs en 593 material,body : cast iron material spec,body : ci is 210 fg 260 material,trim : shaft ss 410 disc sgi en1563 en gjs 400 15 bore : 350 mm pressure designation : pn 10 nominal size : 350 mm additional information : manual worm gear box operated bi directional flow with worm gear box valve should be suitable to mount between ansi b16.5 cl150 flanges. 00050 m1878270552 specification valve,butterfly type : wafer design spec : is 13095/bs 5155/api 609 material,body : cast iron material spec,body : is 210 grade fg200 material,seat : epdm pressure designation : pn 10 nominal size : 150 mm additional information : manual operated moc: disc material:ss316, stem material:ss 410, operating type : gear box with standard worm wheel type, valve should be suitable to mount between ansi b16.5 cl150 flanges. other moc and dimensions shall be as per standard 00060 m1878570710 specification valve,butterfly type : wafer design spec : is 13095/bs 5155/api 609/bs en 593 material,body : cast iron material spec,body : ci is 210 fg 260 material,trim : shaft ss 410 disc sgi en1563 en gjs 400 15 bore : 100 mm pressure designation : pn 10 nominal size : 100 mm additional information : pneumatic operated with pneumatic actuator and accessories, air pressure : 5ksc valve should be suitable to mount between ansi b16.5 cl150 flanges. 00070 m1878170958 specification valve,butterfly type : wafer design spec : is 13095/bs 5155/api 609/bs en 593 material,body : cast iron material spec,body : ci is 210 fg 260 material,trim : shaft ss 410 page 4 of 11 ntpc limited ( a government of india enterprise ) tender enquiry no. 9900290461 disc sgi en1563 en gjs 400 15 bore : 250 mm pressure designation : pn 10 nominal size : 250 mm additional information : manual worm gear box operated bi directional flow with worm gearbox and handwheel valve should be suitable to mount between ansi b16.5 cl150 flanges. 00080 m1878219608 specification valve,butterfly type : wafer design spec : is 13095/bs 5155/api 609/bs en 593 material,body : cast iron material spec,body : ci is 210 fg 260 material,trim : shaft ss 410 disc sgi en1563 en gjs 400 15 bore : 400 mm pressure designation : pn 10 nominal size : 400 mm additional information : manual worm gb operated bi directional flow with worm gearbox and handwheel valve should be suitable to mount between ansi b16.5 cl150 flanges. 00090 m1878170776 specification valve,butterfly type : wafer design spec : is 13095/bs 5155/api 609/bs en 593 material,body : cast iron material spec,body : ci is 210 fg 260 material,trim : shaft ss 410 disc sgi en1563 en gjs 400 15 bore : 450 mm pressure designation : pn 10 nominal size : 450 mm additional information : manual worm gear box operated bi directional flow with worm gearbox and handwheel valve should be suitable to mount between ansi b16.5 cl150 flanges. 00100 m1878900257 specification valve,butterfly design spec : bs 5155 end connection : flanged ends asme b16.5 150# material,body : spheroidal graphite iron material spec,body : din 1693 ggg40 + epoxy material,seat : ht silicon bore : 150 mm pressure designation : pn6 length,f to f : 56 nominal size : 150 mm additional information : pneumatically operated disc material:sgi din1693 ggg40+epoxy page 5 of 11 ntpc limited ( a government of india enterprise ) tender enquiry no. 9900290461 shaft material:stainless steel 410 pneumatic pressure for actuator design 5kg/cm2 valve seat leakage class zero leakage,tight shut off limit switch box 2 cable entries 1/2 inch npt (f) all mounting bracket/coupler are in mild steel material flow direction bi directional with pneumatic actuator and accessories total quantity : 102...

East Central Railway - Bihar

46333607 supply of safety bracket assembly.safety bracket assembly.,safety bracket assembly with nut and bolt for mr,bp hose pipes. [ warranty period: 30 mo nths after the date of delivery ] ]...

Eastern Railways - Bihar

46286742 auction sale of 1)erc(sc)=20255 nos., 2)erc broken(sc)=3655 nos.,3)metal liner of sorts(sc)=20101 nos., 4)lc bracket (sc)=660 nos., 5)ms split cottor (sc)=242 nos., 6) si,bar of sorts (sc) =44 nos. 7)b/nuts of sorts (sc)=161 nos.,8)plate screw (sc)=8266 nos.9)distance block (sc)=08 nos., 10) check block of sorts(sc)=04nos., 11) comp. f/plate 52/60kg(sc)=6.5 set, 12) sej b/plate(sc)=41nos., 13) bracket of sorts 52kg (sc)=48 nos.,14)d&o tie bar(sc)=45 nos., 15)d&o tie bar broken(sc)=44 nos.,16) lug(sc)=236 nos., 17)m.s.plate(sc)=02 nos., 18)b/plate of sorts (sc)=10 nos., 19)ins.g.t plate(sc)=02 nos., 20) j/f/plate 52kg without hole(sc)=800 nos., 21)clamp with b/nut(sc)=600 nos, 22)m.s.loose jaw(sc)=512 nos, 23)fittings of cms xing 52kg 1 in 12(sc)=13 sets, 24) fittings of d/xing s/slip 52kg(sc)=02 sets, 25) fittings of cms xing 52 kg 1in 8.5 (sc)=06 sets, 26)fittings of sej rail 52 kg(sc)= 03 sets, 27) fittings of switch 52kg 1 in 8.5(sc)=04 sets,28)fittings of xing 52kg 1 in 12(sc)=01 set, 29)fittings of d/xing d/slip 52 kg(sc)=03 sets, 30)fittings of dereling switch 52kg(sc)=13 sets, 31)slide chair with b/plate 52 kg 1 in 12(sc)=02 sets, 32) slide chair with b/plate d/s 52 kg (sc)=01 set, 33) fittings of switch 52 kg 1 in 12(sc)=01 set, 34) foot rail 52kg (sc)=228.75mtrs in 53 psc, 35) head rail 52 kg (sc)=453.96mtrs in 81 pcs, 36) cut piece rail 75lbs (sc)=32.73 mtrs in 46 pieces, 37) cut piece rail 52 kg (sc)=138.05 mtrs in 189 pieces, 38) cut piece rail 60kg (sc)=54.10 m. in 95 pcs, 39) cut piece rail 90r (sc)=51.85m in 92 pcs....

Indian Army - Bihar

46275409 bids are invited for 100 hours repair kit for rotax 582 engine 950211 reduction gear box gasket type c 850775 double gasket 0.5 mm 831713 o ring air screw din 3771 3, 2x1 831450 carburetor cap rubber ring 963697 needle jet 2, 72 961043 needle jet 11g2 830720 float bracket gasket 950730 jet needle o ring 2.5 x 1.5 850540 o ring 83 x 2 850040 rubber ring 152.5 x 205 938795 spring 66mm 850633 exhaust gasket 861184 float 261625 sieve sleves 963147 idle jet 831700 rubber ring 126x1.5x3.5 total quantity : 337...

East Central Railway - Bihar

46270779 supply of rubber kit for mu2b valverubber kit for mu2b valve,rubber kit for mu2b valve , consist of 2 items. sr. no(1)o ring 15/16 inch od wabco pt no. 524614 qty/ kit 07. sr no. (2)gasket pipe bracket wabco pt no. 558987 qty/ kit 01. [ warranty period: 30 months after the date of delivery ] ] => limited...

All India Institute Of Medical Sciences - Bihar

46254845 tender for construction of prefabricated pre engineered building at roof top of ipd b block b side, department of anaesthesiology at aiims patna.; 1 reinforced cement concretereinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 2 centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers 3 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.thermo mechanically treated bars of grade fe 500d or more. 4 cladding work providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 5 wood and p. v. c. workproviding wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). sal wood 6 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including isi marked stainless steel butt hinges with necessary screws 7 providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with isi, is : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. 8 providing and fixing aluminium sliding door bolts, isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :300x16 mm 9 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm 10 providing and fixing aluminium handles, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm 11 providing and fixing aluminium hanging floor door stopper, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.twin rubber stopper 12 providing and fixing factory made upvc glazed/ wire mesh windows/ doors comprising of lead free upvc multi chambered frame, sash and mullion/ coupler (wherever required) extruded profiles having minimum wall thickness of 1.70 mm for series r1 and r2 profiles and 2.10 mm for series r3 and r4 profiles conforming to en: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per cpwd specification, upvc extruded glazing beads, interlocks and inline sash adaptor (whereever required) of appropriate dimension, epdm gasket, hardware, ss 304 grade fasteners of minimum 8 mm dia. with countersunk head, comprising of matching polyamide pa6 grade sleeve for fixing frame to finished wall as per is 1367: part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. after fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to cpwd specification & direction of engineer in charge. section of steel reinforcement and cross sections of upvc profiles to be as per design approved by engineer in charge. wire mesh/ glazing of plain/toughened/ laminated/ double glass unit with/without high performance coatings as per design requirements and conforming to is: 3548 & is: 16231 shall be paid separately. note: structural design proof checked from a government engineering institute, to be provided by the manufacturer for: (iii) sites with basic wind speed > 45 m/sec as per is 875 part 3 (iv) sites with structure height more than 20m for all wind speeds.three track three panels sliding window with aluminium channel for roller track, wool pile, nylon rollers with ss 304 body.using r4 series with frame (115mm & above) x (45mm & above) & sash (44mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on two end panels along with multi point locking system. (height above 1.8 meter). 13 steel workstructural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 14 flooring providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to is : 15622, of approved make, in all colours, shades, except white, ivory, grey, fume red brown, laid on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete. 15 providing and laying vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to i.s. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.size of tile 600x600 mm 16 roofingproviding and fixing thermal insulation with resin bonded fibre glass wool conforming to is: 8183. density 16 kg/m³, 50 mm thick, wrapped in 200g virgin polythene bags placed over existing false ceiling and held in position by criss crossing gi wire. 17 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes. 110 mm diameter 18 providing and fixing on wall face unplasticised pvc moulded fittings/ accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion.bend 87.5°110 mm bend 19 providing and fixing on wall face unplasticised pvc moulded fittings/ accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion.shoe (plain) 110 mm shoe 20 providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling/ self tapping screws cmplete: ridges plain (500 600mm) 21 providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling/ self tapping screws cmplete: flashings/ aprons.( upto 600 mm) 22 providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling/ self tapping screws cmplete: gutter (600 mm over all girth) 23 providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main t runner with suitably spacedjoints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross t of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main t at 600 mm center to center to form a grid of 1200x600 mm and secondary cross t of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. main t runners to be suspended from ceiling using gi slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm gi adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main t, bottom exposed width of 24 mm of all t sections shall be pre painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by engineer in charge. gi metal ceiling lay in perforated tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of gi sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having nrc (noise reduction coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black glass fiber acoustical fleece. 24 finishing finishing walls with acrylic smooth exterior paint of required shade :new work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 25 finishing with deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers specifications : two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm 26 dismantling and demolishingdemolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer in charge. nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) 27 dismantling g.i. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of engineer in charge :above 40 mm nominal bore 28 providing and fixing g.i. pipes complete with g.i. fittings and clamps including cutting and making good the walls etc. internal work exposed on wall40 mm dia nominal bore 29 providing and fixing g.i. pipes complete with g.i. fittings and clamps including cutting and making good the walls etc. internal work exposed on wall 50 mm dia nominal bore 30 making connection of g.i. distribution branch with g.i. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :25 to 40 mm nominal bore 31 providing and fixing gun metal gate valve with c.i. wheel of approved quality (screwed end) : 40 mm nominal bore 32 providing and fixing g.i. union in g.i. pipe including cutting and threading the pipe and making long screws etc. complete (new work):40 mm nominal bore 33 providing and fixing g.i. union in g.i. pipe including cutting and threading the pipe and making long screws etc. complete (new work): 50mm nominal bore 34 providing and fixing glazing in aluminium door, window , ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . (cost of aluminium snap beading shall be paidin basic item):with float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) 35 water proofingproviding and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.(b) laying second layer of fibre glass cloth when the first layer is still green. overlaps of joints of fibre cloth should not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. this will be allowed to air cure for 4 hours followed by water curing for 48 hours. the entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately .for the purpose of measurement the entire treated surface will be measured. 36 new technologies and materialsdesigning, providing, installing and fixing factory finished custom designed cold form light gauge steel framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. the steel sheet shall be galvanized (az 150gms aluminium zinc alloy coated steel having minimum yield strength 300 550 mpa) conforming to aisi specifications and ibc 2009 for cold formed steel framing and construction and also as per is: 875 1987, iso 800 1984 and is:801 1975. the wind load shall be as per provisions of is 875 (part iii). lgsfs frame shall be designed as per is: 801 using commercially available software such as frame cad pro 11.7/ staad pro v8i/ architekv2.5.16/ revit architecture 2011 or equivalent.proper usage of connection accessories like heavy duty tension ties, light duty hold ons, twist straps (to connect truss with wall frames), strong tie, tie rod, h brackets, boxing sections, l shaped angles for better structural stability. the framing section shall be cold form c type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple/ slot at required locations as per approved drawings. the slots will be along centre line of webs and shall be spaced minimum 250mm away from both ends of the member. the frame can besupplied in panelized or knock down condition in specific dimensions and fastened with screws extending through the steel beyond by minimum of three exposed threads. all self drilling tapping screws for joining the members shall have a type ii coating in accordance with astm b633(13) or equivalent corrosion protection of gauge 10 & 12, tpi 16 & 8 of length 20mm. the frames shall be fixed to rcc slab or tie beam over neoprene rubber using self expanding carbon steel anchor bolt of dia as per approved drawings. design subject to minimum 12mm diameter and 121mm length conforming to aisi 304 and 316 at 500mm c/c with minimum embedment of 100mm in rcc (rcc to be paid separately) and located not more than 300mm from corners or termination of bottom tracks complete in all respects. the item also includes the submission of stability reports duly examined and issued by any nit/iit. the rate includes the concept design, detailed design, fabrication of sections, transportation, installation and all required fixingarrangement at site as described above. 37 providing and fixing of external wall system on light gauge steel frame work with outer face cement boards as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c/c of approved make. a groove of 2 mm to 3mmshallbe maintained andgrooves shallbe sealed withsilicon based sealant. the board shall be fixed in a staggered pattern. screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm and. internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c/c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately)outer face outer face having 6mm thick fiber cement board type a,category ivasper is:14862:2000fixedon9mmthick fiber cement board, type a, category iv as per is:14862:2000 (high pressure steam cured)inner face 12.5 mm thick gypsum plaster boardconformingtois2095:2011fixedon 8mmthickfibre cementboardoftypeb,category iiiconformingto is:14862:2000 (high pressure steam cured) 38 providing and fixing internal wall panels on light gauge steel frame work with 12.5mm thick gypsum plaster board conforming is 2095:2011 fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c/c of approved make, screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. proper taping and jointing to be done using fiber mesh tape andepoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separatelycement fiber board 8 mm thick oftype b, category iii as per is 14862:2000 (high pressure steam cured) 39 supply , fittings and fixing of roller blinds with pully mechanism system with black out rich fabric etc all completed as per direction of engineer in charge 40 providing and fixing prefab roof made up of sandwich panel of 100mm thick of expended polystrene eps in pills having one sides precoated galvanised steel sheet of 0.5 mm thickon side flat and other side corrugated profiled roof with heat resistance etc all complete job 41 wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm frls pvc insulated copper conductor single core cable in surface i recessed steel conduit, with modular switch, modular plate, suitable gl box and earthing the point with 1.5 sq. mm frls pvc insulated copper conductor single core cable etc. as required.group a 42 wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed steel conduit as required 2 x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire 43 wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed steel conduit as required2 x 4 sq. mm + 1 x 4 sq. mm earth wire 44 wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed steel conduit as required 2 x 6 sq. mm + 1 x 6 sq. mm earth wire 45 wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed steel conduit as required 4 x 16 sq. mm + 2 x 6 sq. mm earth wire 46 supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 a switch 47 supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 a switch 48 supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 a socket outlet 49 supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 a socket outlet 50 supplying and fixing following size/ modules, gl box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 module (100mmx75mm) 51 supplying and fixing following size/ modules, gl box alongwith modular base & cover plate for modular switches in recess etc. as required.6 module (200mmx75mm) 52 supplying and fixing following size/ modules, gl box alongwith modular base & cover plate for modular switches in recess etc. as required.8 module (200mmx75mm) 53 installation,testingandcommissioningofceilingfan,including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mmfrlspvcinsulated,copperconductor,singlecorecable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. 54 installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. upto 450 mm sweep 55 supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, tpn mcb distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting mcb’s (but without mcb’s and incomer ) as required .(note : vertical type mcb tpdb is normally used where 3 phase outlets are required.) 8 way (4 + 24), double door 56 supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 ka, “c” curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. single pole 57 supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 ka, “c” curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required.single pole and neutral 58 supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 ka, “c” curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. triple pole and neutral 59 supplying and fixing 20 amps, 240 volts, spn industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps “c” curve, sp, mcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing andmmissioning etc. as required. 60 supplying, installation, testing & commisioning of following capacity plug in/ tap off box on the existing air insulated compact type bus trunking/ rising mains for use on 3 phase 4 wire 415 v, 50hz a.c. supply made with 1.6mm thick sheet steel enclosure (ip54) duly powder coated with provision of mccb (but without mccb) complete etc. as required125 a, lsc= 15ka for 1 sec (make: c&s) 61 providing and fixing 6 swg dia gi. wire on surface or in recess for loop earthing as required. 62 laying and fixing of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size on wall surface as required.above 35 sq. mm and upto 95 sq. mm(clamped with 25x3mm ms flat clamp 63 supplying and making end termination with brass compression gland and aluminium lugs for following size of pvc insulated and pvc sheathed / xlpe aluminium conductor cable of 1.1 kv grade as required. 3½ x 70 sq. mm (38mm) 64 supply, installation, testing and commissioning of 1200 mm sweep, bee 5 star rated, ceiling fan with brush less direct current (bldc) motor, class of insulation: b, 3 nos.blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, power factor not less than 0.9, service value (cmm/w) minimum 6.85, air delivery minimum 215 cmm, 350 rpm (tolerance as per is : 374 2019), thd less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree c (max.), insulation resistance more than2 mega ohm, suitable for 230 v, 50 hz, single phase ac supply, earthing etc. complete as required. 65 supplying & fixing 3.5 c x 70 sq. mm alarmoured cable xlpe 66 sitc of 15/18 w led down light cool day1x1 ftmake:syska,havells,philips. 67 sitc of 36/40 w led down light cool day2x2 ftmake:syska,havells,philips. 68 sitc of 300 mm exhaust fan 69 supply and fixing of 25 mm pvc casing bit 70 supply and fixing of 125 amp. 4 p 25 ka mccb at & fmmake: havells,l&t 71 metallic enclosure with spreader link suitable for above mentioned mccb 72 2 ton , bee 5 star invertersplit ac 73 providing and fixing copper line with insulation suitable for 2 tr split ac units (suctipon and discharge taken in one unit)dia of pipe: 5/8 &1/4 74 supplying and fixing drain pipe as per suitable for 2 tr split ac unit. 75 standard outdoor stand suitable for outdoor units for 2 tr split ac unit. 76 3 core 4 sq mm pvc insulated copper wire. 77 installation of ac 78 98 inch ultra hd interactive flat panel display with inbuilt android 11 os ,google pay store , 8 gb ram & 64 gb storage with two inbuilt speakers of 25 watt each along with subwoofer , multiple connectivity option like , 3 nos. of hdmi in vga in , audio in and out , 4 nos. of usb 3.0 rj45, inbuit dual band wi fi (2.4 & 5 ghz.)with hotspot and bluetooth 5.0 , interactive teachinng software , 4 mm tempered glass with anti glare coating and more with wall mount kit. ...

East Central Railway - Bihar

46252305 supply of safety bracket for boxnhl wagonsafety bracket for boxnhl wagon,safety bracket for boxnhl wagon to rdso drg. no. wd 09034 s 13 alt 2, item no. 7. [ war ranty period: 30 months after the date of delivery ] ]...

East Central Railway - Bihar

46242314 supply of cross bar and bracket for brake cylindercross bar and bracket for brake cylinder,cross bar and bracket for brake cylinder for boxnhl wagon to drg. no. wd 08008 s 16 alt 5 , item no. 1. [ warranty period: 30 months after the date of delivery ] ]...

Department of Labour Resources - Bihar

46217440 the directorate of employment & training (training wing), labour resources department, govt. of bihar (the tendering authority) invites e tenders from registered indian manufacturers/oem/oem authorised distributers/dealers for supply, installation and commissioning (with amc as applicable) of machines/tools/ equipment as per the specified requirements and technical specifications, grouped under schedule i & ii of this rfq at various govt. itis in bihar.1 c : machineries and equipments lathe s.s. & s.c. (all geared head stock) with minimum specification as:(with d.r.o. z & y axis) 2 c : machineries and equipments lathe s.s & s.c.(all geared type) with minimum specification as: 3 c : machineries and equipments lathe tool room s.s. & s.c. (all geared type) with minimum specification as (with d.r.o. z & y axis) 4 c : machineries and equipments grinding machine pedestal type 5 c : machineries and equipments drill machine pillar type motorized 6 c : machineries and equipments power saw machine – hydraulic feedsystem 7 c. general installation/ machineries discrete component trainer / basic electronics trainer 8 c. general installation/ machineries drilling machine bench to drill up to 12mm dia. along with accessories 9 c. general installation/ machineries grinding machine (general purpose) d.e. pedestal with 300 mm dia. wheels rough and smooth 10 c. general installation/ machineries tractor diesel engine 4 stroke for dismantling and assembling with 11 c. general installation/ machineries welding plant oxy acetylene complete ( high pressure) 12 c. general installation/ machineries wheel type tractor fitted with diesel engine with standardaccessories 13 c. general installation/machineries tractor 14 c. general installation/machineries tractor 15 c. general machinery universal testing machine for plastic 16 c. general machinery plastic scrap grinder 17 c. general machinery pre heater 18 c. general machinery automatic screw type injection moulding machine 19 c. general machinery hand operated compression mouldingmachine 20 c. general machinery automatic compression moulding machine 21 c. general machinery hand operated blow moulding machine 22 c. general machinery automatic extrusion blow moulding machine 23 c. general machinery extruder of 40 kg/hr. plasticizing capacity 24 c. general machinery pipe extruder of 40 kg/hr. plasticizingcapacity 25 c. general machinery extruderof40 kg/hr. plasticizing capacity 26 c. general machinery thermo/vacuum forming machine with mould 27 c. general machinery rotational moulding machine with mould 28 c. general machinery hydraulic trainer kit 29 c. general machinery pneumatic trainer kit 30 c. general machinery programmable logic control 31 c. general machinery strech blow moulding machine 1 literwith mould 32 c. general machinery air compressor with air treatment accessories 5 hp 33 c. general machinery shop outfit air compressor with maximum working pressure 34 c. general machinery shop outfit moulding sand muller 35 c. general machinery shop outfit co2 cylinder with co2 probe and rubber hoses 36 c. general machinery shop outfit heating and pumping unit to suit to oil fired tilting type crucible furnace with heating pressure gauge etc.motorized rotary gear oil pump pre heater. 37 c. general machinery shop outfit sand testing equipment permeability meter, universal strength tester, sieve shaker, standard sand rammer, shatter index tester, clay content tester,speedy moisture teller. 38 c. general machinery shop outfit moulding machine hand squeeze with stripping device pin lift type. 39 c. general machinery shop outfit weighing machine 40 c. general machinery shop outfit pedestal grinder de operated 41 c. general machinery shop outfit core oven 42 c. general machinery shop outfit muffle furnace (electric) 43 c. general machinery shop outfit auto sand riddle 44 c. general machinery shop outfit one man ladle 45 c. general machinery shop outfit two man ladle 46 c. general machinery shop outfit oil fired tilting type crucible furnace 47 c. general machinery shop outfit pit furnace 48 c. general machinery shop outfit gravity die casting machine 49 c. general machinery shop outfit usg testing machine 50 c. general machinery shop outfit magnetic particle testing equipment 51 c. general machinery shop outfit induction furnace 52 d. mechatronics lab outfit simple servomotor trainer kit. 53 d. mechatronics lab outfit simple stepper motor trainer kit. 54 d. mechatronics lab outfit application trainer kit of proximity sensor, float switch, and reed switch 55 d. mechatronics lab outfit electro pneumatic control trainer kit using plc with required components. 56 d. mechatronics lab outfit electro hydraulic control trainer kit using plc with required components. 57 d. mechatronics lab outfit linear scale setup for positional accuracy check 58 d. mechatronics lab outfit plc based conveyor system with pick and place and sorting of objects (pneumatic andhydraulic)) 59 d. mechatronics lab outfit cut section models of pneumatic and hydraulic motors ,pumps 60 e. general machinery installation d.e. pedestal grinding machine withwheels rough and smooth 61 e. general shop outfit sensitive drilling machine 62 e. general shop outfit shearing machine (lever type) hand operated complete 63 e. general shop outfit hydraulic surface grinding machine 64 e. general shop outfit universal cylindrical grinding machine 65 f. general machinery shop outfit slotter 66 f. general machinery shop outfit ss and sc centre lathe (all geared) with specification as: 67 f. general machinery shop outfit tool and cutter grinder 68 f. general machinery shop outfit drilling machine pillar 69 f. general machinery shop outfit radial drill 70 f. general machinery shop outfit double ended pedestal grinder 71 f. general machinery shop outfit universal milling machine with minimum specification as: 72 f. general machinery shop outfit horizontal milling machine with minimum specification as: 73 f. general machinery shop outfit vertical milling machine with minimum specification as: 74 f. general machinery shop outfit surface grinding machine with minimum specification as: 75 f. general machinery shop outfit cylindrical grinder 76 f. general machinery shop outfit cnc lathe/cnc turn centre 77 f. general machinery shop outfit cnc vertical machining centre 78 f. general machinery shop outfit cnc milling tools 79 f. general machinery shop outfit cnc hole machining tools 80 general shop outfit welding transformer 81 general shop outfit welding transformer (or) inverter based welding machine (igbt) 82 general shop outfit d.c arc welding rectifiers set with all accessories 83 general shop outfit gmaw welding machine 84 general shop outfit ac/dc gtaw welding machine 85 general shop outfit air plasma cutting equipment 86 general shop outfit air compressor suitable for above air plasma cutting system. 87 general shop outfit spot welding machine 88 general shop outfit portable gas cutting machine (pug) 89 general shop outfit pedestal grinder fitted with coarse and medium grain size grindingwheels 90 general shop outfit bench grinder fitted with fine grain size silicon carbide green grindingwheel 91 general shop outfit hand shearing machine capacity 92 general shop outfit power saw machine 93 general shop outfit portable drilling machine 94 general shop outfit oven, electrode drying 95 general shop outfit welding simulators for smaw/gtaw/gmaw 96 general shop outfit water cooled induction welding/ brazing machine 97 general shop outfit plastic welding machine with hot air gun 98 general shop outfit swaging and flooring tool kit 450tubing 99 general shop outfit air conditioned crdi vehicle in running condition lmv 100 general shop outfit arbor press hand operated 2 ton capacity 101 general shop outfit automotive diesel smokemeter (for diesel engine) 102 general shop outfit bench lever shears 103 general shop outfit dual magnetization yoke 104 general shop outfit heavy commercial vehicle type (withoutbody on frame) 105 general shop outfit hydraulic jack hi lift type 3 ton capacity, and 5 ton capacity 106 general shop outfit liquid penetrate inspection kit 107 general shop outfit pipe bending machine (hydraulic type) 108 general shop outfit pneumatic rivet gun with standard accessories 109 general shop outfit tin smiths bench folder 110 general shop outfit trolley type portable air 111 general shop outfit welding plant oxy acetylene complete ( high pressure) 112 general shop outfit welding transformer with all accessoriesincluding consumables 113 general shop outfit diesel engine six cylinder in running condition 114 general shop outfit diesel engine – crdi 4 strokefor dismantling and assembling with swiveling stand. 115 general shop outfit diesel engine (running condition) stationary type single cylinder 116 general shop outfit hydraulic jack hi lift type 117 general shop outfit multi scan tool to scan engine,abs & ebd, at, srs, body control and immobilizer 118 general shop outfit spring tension tester 119 general shop outfit working condition of diesel engine – crdi 4 stroke engine, assembly with fault simulation board 120 general shop outfit cut section of 4/6 cylinder dieselengine in moving condition to show movement of internal parts 121 general shop outfit diesel engine six cylinder in running condition 122 general shop outfit air bag simulator 123 general shop outfit air conditioning service unit (car) 124 general shop outfit four stroke petrol engine with cng setup working condition 125 general shop outfit heavy commercial vehicle 126 general shop outfit mpfi petrol engine with swiveling stand along with special tools for dismantling and assembling 127 general shop outfit petrol engine(2 stroke) motor cycle/scooter along with special tools and accessories (optional)* if not available in market videodemonstration may be used to explain working. 128 general shop outfit transfer case with stand fordismantling and assembly. 129 general shop outfit tube/ tyre vulcanizing machine 130 general shop outfit two post car lift – capacity 4000kg 131 general shop outfit tyre changer machine 132 general shop outfit ultrasonic injection cleaning equipment 133 general shop outfit wheel alignment machine –computerized 3d (optional) 134 general shop outfit wheel balancing machine 135 general shop outfit working condition of petrol mpfi engine assembly with fault simulation board 136 general shop outfit working condition of e.v(electric vehicle ) car 137 b. instruments and general shop outfit steel rule graduated both in metric andenglish unit 138 b. instruments and general shop outfit straight edge steel 139 b. instruments and general shop outfit spirit level metal type 2 140 b. instruments and general shop outfit stud extractor ezy out 141 b. instruments and general shop outfit micrometer inside with extension rods. 142 b. instruments and general shop outfit vernier caliper 143 b. instruments and general shop outfit vernier height gauges 144 b. instruments and general shop outfit vernier bevel protractor blade withacute angle attachment 145 b. instruments and general shop outfit screw pitch gauge metric 146 b. instruments and general shop outfit wire gauge, metric standard. 147 c. tools for allied trade trammel 148 c. tools for allied trade pocker 149 c. tools for allied trade prick punch 150 c. tools for allied trade mallet. 151 c. tools for allied trade aviation snips straight cut 152 c. tools for allied trade flat headed hammers with handle. 153 c. tools for allied trade planishing hammer. 154 c. tools for allied trade snip bent left cut 155 c. tools for allied trade stake hatchet with leg. 156 c. tools for allied trade stake grooving. 157 d. modified list of tools for the 2nd year for fitter trade slip gauge as johnson metric set. 158 d. modified list of tools for the 2nd year for fitter trade gauge snap go and not go 159 d. modified list of tools for the 2nd year for fitter trade gauge plug 160 d. modified list of tools for the 2nd year for fitter trade gauge telescopic set. 161 d. modified list of tools for the 2nd year for fitter trade dial test indicator on stand 162 d. modified list of tools for the 2nd year for fitter trade sine bar 163 d. modified list of tools for the 2nd year for fitter trade dial vernier caliper. (universal type) 164 d. modified list of tools for the 2nd year for fitter trade screw thread micrometer withinterchangeable. pitch anvils for checking metric threads 60. 165 d. modified list of tools for the 2nd year for fitter trade depth micrometer. 0 25 mm 166 d. modified list of tools for the 2nd year for fitter trade digital vernier caliper. 167 d. modified list of tools for the 2nd year for fitter trade digital micrometer outside. 168 d. modified list of tools for the 2nd year for fitter trade comparators gauge dial indication withstand and bracket. 169 d. modified list of tools for the 2nd year for fitter trade engineers try square (knife edge) 170 d. modified list of tools for the 2nd year for fitter trade surface roughness comparison plates 171 d. modified list of tools for the 2nd year for fitter trade digital vernier caliper 172 d. modified list of tools for the 2nd year for fitter trade vernier bevel protector 173 b. instruments and general shop outfit adjustable spanner (pipe wrench) 174 b. instruments and general shop outfit ac alternator slip ring puller 175 b. instruments and general shop outfit air blow gun with standardaccessories 176 b. instruments and general shop outfit air ratchet 177 b. instruments and general shop outfit air impact wrench 178 b. instruments and general shop outfit auto electrical test bench 179 b. instruments and general shop outfit battery –charger 180 b. instruments and general shop outfit blow lamp 181 b. instruments and general shop outfit belt tensioner gauge 182 b. instruments and general shop outfit car jet washer with standard accessories 183 b. instruments and general shop outfit chain pulley block capacity withtripod stand 184 b. instruments and general shop outfit chisel flat 185 b. instruments and general shop outfit circlip pliers expanding andcontracting 186 b. instruments and general shop outfit cleaning tray 187 b. instruments and general shop outfit compression testing gauge 188 b. instruments and general shop outfit cylinder bore gauge capacity 189 b. instruments and general shop outfit depth micrometer 190 b. instruments and general shop outfit dial gauge type 1 gr. a (complete with clamping devices and withmagnetic stand) 191 b. instruments and general shop outfit different type of engine bearingmodel 192 b. instruments and general shop outfit different type of piston model 193 b. instruments and general shop outfit engineers stethoscope 194 b. instruments and general shop outfit files assorted sizes and typesincluding safe edge file (20 no’s) 195 b. instruments and general shop outfit fuel feed pump for diesel 196 b. instruments and general shop outfit fuel injection pump (diesel)inline 197 b. instruments and general shop outfit fuel injection pump ve pump / distributor fuel rotary pump (dpc) pumps / along with specialtools and accessories 198 b. instruments and general shop outfit grease gun 199 b. instruments and general shop outfit grease gun heavy duty trolleytype 200 b. instruments and general shop outfit growler 201 b. instruments and general shop outfit hand operated crimpingtool/wire 202 b. instruments and general shop outfit injector – multi hole type, pintletype 203 b. instruments and general shop outfit injector testing set 204 b. instruments and general shop outfit magneto spanner set with 8spanners 205 b. instruments and general shop outfit automotive oil pump fordismantling and assembling. 206 b. instruments and general shop outfit philips screw driver set of 5pieces (pozidrivandtorx drive) 207 b. instruments and general shop outfit piston ring expander andremover. 208 b. instruments and general shop outfit scriber with scribing blackuniversal 209 b. instruments and general shop outfit spanner t. flocks for screwing upand up screwing inaccessible 210 b. instruments and general shop outfit spark plug spanner 14mm x18mm x size 211 b. instruments and general shop outfit starter motor axial type, pre engagement type & co axial type 212 b. instruments and general shop outfit surface gauge with dial testindicator plunger type 213 b. instruments and general shop outfit tyre pressure gauge with holdingnipple 214 b. instruments and general shop outfit universal puller for removingpulleys, bearings 215 b. instruments and general shop outfit v’ block 75 x 38 mm pair withclamps 216 b. instruments and general shop outfit valve spring compressoruniversal 217 b. instruments and general shop outfit automotive water pump fordismantling and assembling 218 b. instruments and general shop outfit working model of air brake assembly 219 b. instruments and general shop outfit alternator assembly used forlmv 220 b. instruments and general shop outfit carburetor – solex, mikuny fordismantling and assembling 221 b. instruments and general shop outfit chain pulley block 3 ton capacitywith tripod stand 222 b. instruments and general shop outfit cut section model of mock layout of a motor car –electrical system working model 223 b. instruments and general shop outfit cut section models of shockabsorbers 224 b. instruments and general shop outfit cut section of cross ply and radialtyres 225 b. instruments and general shop outfit cut section working model of automatic transmission gear box 226 b. instruments and general shop outfit cut section working model ofcentrifugal clutch assembly. 227 b. instruments and general shop outfit cut section working model ofdiaphragm clutch assembly. 228 b. instruments and general shop outfit cut section working model ofsingle plate clutch assembly 229 b. instruments and general shop outfit demonstration board of electronic ignition system,ignition coil 230 b. instruments and general shop outfit demonstration board of mpfi system 231 b. instruments and general shop outfit disk brake in working condition with caliper assembly with allparts 232 b. instruments and general shop outfit drum brake assembly in workingcondition 233 b. instruments and general shop outfit front axle (rzeeppa joint) withstand for dismantling and assembly 234 b. instruments and general shop outfit full floating axle and semi floating axle assembly 235 b. instruments and general shop outfit functional/experiment model of different type of sensors. 236 b. instruments and general shop outfit steering assembly –1.rack & pinion 2.worm & roller3. recirculating ball 4.power steering5. electric assisted power steering 237 b. instruments and general shop outfit synchronous gear box with standfor dismantling and assembly 238 b. instruments and general shop outfit tandem master cylinder withbooster 239 b. instruments and general shop outfit working model of power windows 240 b. instruments and general shop outfit working model of torqueconverter 241 tools & equipments for engineering drawing hall mini drafter 242 tools & equipments for engineering drawing hall set square 243 b. shop tools, instruments neon (phase) tester 244 b. shop tools, instruments electric soldering iron 245 b. shop tools, instruments tube cutter 246 b. shop tools, instruments allen keyset(metric) 247 b. shop tools, instruments allen keyset(english 248 b. shop tools, instruments soldering station(temp. controlled)with necessary accessories 249 b. shop tools, instruments philips screwdriver 250 b. shop tools, instruments round nose pliers 251 d. rotational/velocity instruments digital type tachometer 252 e. precision instruments digital panel meters voltage & current 253 e. precision instruments d.c. regulated power supply 254 e. precision instruments digital insulation tester 255 e. precision instruments digital multimeter51/2 digit bench top digital multimeter 256 e. precision instruments digital l.c.r. bridge 257 e. precision instruments operational amplifier trainer 258 e. precision instruments trainer on basic digital electronicsi.e. logic gates boolean expression adder, sub tractor, flip flop, counter register, converter etc. 259 e. precision instruments trainers on power suppliers half wave rectifier, full wave rectifier 260 e. precision instruments discrete component trainer with following seven basic modules diode characteristics (si, zener, led) rectifier circuit diode as clipper circuit diode as clamping circuit zener as voltage regulator. transistor type npn & pnp and ce characteristics transistor as a switch 261 g. electrical instruments autotransformer1øand3ø 262 g. electrical instruments calibration test bench for ac and dc voltmeter, ac and dc ammeter, ohmmeter 263 h. pressure instruments u tube manometers 264 h. pressure instruments well type manometer 265 h. pressure instruments inclined limb manometers 266 h. pressure instruments bourdon tube type gauges ofvarious ranges 267 h. pressure instruments capsule type pressure gauges 268 h. pressure instruments dead weight tester & comparator 269 h. pressure instruments pressure regulators with filter and input & output gauges 270 h. pressure instruments differential pressuretransmitter 271 h. pressure instruments differential pressure transmitter (electronic hart/field bus type) 272 h. pressure instruments sensor trainer kit containing following sensorsrtd,ntc thermistor,lm35 , thermocouple j ,k type and ad590 photovoltaic, photoconductive , phototransistor and photodiode air humidity and temperature 273 h. pressure instruments diaphragm type pressure gauges of various ranges 274 h. pressure instruments pressure transducers training kits potentiometercapacitive reluctive strain gauge lvdtload cell servo typepiezo resistive 275 h. pressure instruments experimental setup for pressure measurement consisting of air compressor pressure vessel pressure transmitter controller recorder and final control element, computeri.e. closed loop system or full scope system i.e. pressure instrumentation process controltrainer/simulator 276 h. pressure instruments hart device communicator and calibrator 277 h. pressure instruments pneumatic calibrator 278 h. pressure instruments pressure switches of various ranges 279 h. pressure instruments p to i and i to p converters training platform 280 h. pressure instruments vacuum tester with pump 281 i. flowmeters/ instruments simple tank type quantity meter 282 i. flowmeters/ instruments impeller type flow meter 283 i. flowmeters/ instruments helical and turbine flow meter 284 level control set up with level transmitters controller & control valve complete experimental setup or level simulator 285 o. equipment for microprocessors microcontroller development platform 286 b. tools, measuring instruments and general shop outfit calipers, vernier(digital) 287 b. tools, measuring instruments and general shop outfit height gauge 288 b. tools, measuring instruments and general shop outfit diamond, wheel dressing 289 b. tools, measuring instruments and general shop outfit techometer(digital) 290 b. tools, measuring instruments and general shop outfit demagnetizer chuck 291 b. tools, measuring instruments and general shop outfit static balancing stand for grinding wheel 292 b. tools, measuring instruments and general shop outfit dial test indicator(digital) 293 b. instruments and general shop outfit surface plate 294 b. instruments and general shop outfit marking off table 295 b. instruments and general shop outfit scribing block universal 296 b. instruments and general shop outfit v block 297 b. instruments and general shop outfit try square 298 b. instruments and general shop outfit outside spring caliper 299 b. instruments and general shop outfit divider spring 300 b. instruments and general shop outfit inside spring caliper 301 b. instruments and general shop outfit straight edge steel 302 b. instruments and general shop outfit straight edge steel 303 b. instruments and general shop outfit steel tape 304 b. instruments and general shop outfit steel rule 305 b. instruments and general shop outfit sprit level 306 b. instruments and general shop outfit hammer 307 b. instruments and general shop outfit screw driver, heavy duty 308 b. instruments and general shop outfit hammer lead 309 b. instruments and general shop outfit spindle blade screw driver 310 b. instruments and general shop outfit allen hexagonal keys 311 b. instruments and general shop outfit spanner d.e. 312 b. instruments and general shop outfit adjustable spanner 313 b. instruments and general shop outfit reduction sleeve morse 314 b. instruments and general shop outfit angle plate size 315 b. instruments and general shop outfit solid parallels in pairs (different sizes) in metric 316 b. instruments and general shop outfit oil can pressure feed 317 b. instruments and general shop outfit oil stone 318 b. instruments and general shop outfit number drills h.s.s. (parallel shank) 319 b. instruments and general shop outfit punch letter . 320 b. instruments and general shop outfit punch number 321 b. instruments and general shop outfit twist drills 322 b. instruments and general shop outfit drill chuck 323 b. instruments and general shop outfit centre drill 324 b. instruments and general shop outfit grinding wheel dresser (diamond) 325 b. instruments and general shop outfit grinding wheel dresser huntington type 326 b. instruments and general shop outfit tap and die in box metric pitch 327 b. instruments and general shop outfit drill h.s.s. taper shank 328 b. instruments and general shop outfit file half round 329 b. instruments and general shop outfit file triangular smooth 330 b. instruments and general shop outfit needle file 331 b. instruments and general shop outfit file square 332 b. instruments and general shop outfit reamer 333 b. instruments and general shop outfit reamer adjustable 334 b. instruments and general shop outfit tool bits 335 b. instruments and general shop outfit tool bits 336 b. instruments and general shop outfit tool bits holder (armstrong) l.h 337 b. instruments and general shop outfit tool bits holder (armstrong) r.h. 338 b. instruments and general shop outfit assorted tools and bit holders for lathe, shaper, slotter& planner in different shapes and sizes 339 b. instruments and general shop outfit hacksaw frame adjustable 340 b. instruments and general shop outfit table chuck 341 b. instruments and general shop outfit bench vice 342 b. instruments and general shop outfit machine vice 343 b. instruments and general shop outfit machine vice 344 b. instruments and general shop outfit hand vice 345 b. instruments and general shop outfit radius turning attachment 346 b. instruments and general shop outfit angle turning attachment 347 b. instruments and general shop outfit compound angle vice (standard sine) 348 b. instruments and general shop outfit universal machine vice 349 b. instruments and general shop outfit universal table angle plate 350 b. instruments and general shop outfit shaper tool holder turret type to suit the machine 351 b. instruments and general shop outfit base chuck for slotter to suit the machine 352 b. instruments and general shop outfit shaper indexing center to suit the machine 353 b. instruments and general shop outfit knurling tools 354 b. instruments and general shop outfit plier cutting 355 b. instruments and general shop outfit carbide tipped tools of different sizes and shapes (throw away tips) 356 b. instruments and general shop outfit hand hammer 357 c. milling cutters milling cutter cylindrical cutter 358 c. milling cutters milling cutter cylindrical cutter 359 c. milling cutters milling cutter 360 c. milling cutters milling cutter 361 c. milling cutters milling cutter 362 c. milling cutters milling cutter 363 c. milling cutters milling cutter side and face cutter 364 c. milling cutters milling cutter side and face cutter 365 c. milling cutters milling cutter equal angle cutter 366 c. milling cutters milling cutter equal angle cutter 367 c. milling cutters milling cutter equal angle cutter 368 c. milling cutters milling cutter double angle unequal 369 c. milling cutters milling cutter double angle unequal 370 c. milling cutters milling cutter double angle unequal 371 c. milling cutters milling cutter double angle unequal 372 c. milling cutters milling cutter single angle 373 c. milling cutters milling cutter single angle 374 c. milling cutters milling cutter single angle 375 c. milling cutters milling cutter single angle 376 c. milling cutters milling cutter slitting saw cutter 377 c. milling cutters milling cutter slitting saw cutter 378 c. milling cutters milling cutter shell end mill 379 c. milling cutters milling cutter shell end mill 380 c. milling cutters milling cutter parallel shank end mills 381 c. milling cutters milling cutter t slot cutter with parallel shank 382 c. milling cutters milling cutter concave 383 c. milling cutters milling cutter convex 384 c. milling cutters involute gear cutter 385 d. measuring instruments micrometer outside 386 d. measuring instruments micrometer outside 387 d. measuring instruments micrometer outside 388 d. measuring instruments micrometer outside 389 d. measuring instruments micrometer depth gauge 390 d. measuring instruments digital micrometer 391 d. measuring instruments vernier caliper 392 d. measuring instruments direct reading vernier caliper 393 d. measuring instruments digital vernier caliper 394 d. measuring instruments vernier height gauge q 395 d. measuring instruments vernier gear tooth caliper 396 d. measuring instruments combination 397 d. measuring instruments vernier bevel protractor 398 d. measuring instruments bevel gauge 399 d. measuring instruments telescopic gauge 400 d. measuring instruments sine bar 401 d. measuring instruments universal dial test indicator 402 d. measuring instruments centre gauge com. 403 d. measuring instruments gauge slip box 404 d. measuring instruments gauge screw pitch 405 d. measuring instruments gauge radius 406 d. measuring instruments limit plug gauges 407 d. measuring instruments ring gauges 408 d. measuring instruments taper gauge 409 d. measuring instruments gauge feeler / thickness 410 b. instruments and general shop outfit air blow gun with standard accessories 411 b. instruments and general shop outfit ammeter dc with external shunt 412 b. instruments and general shop outfit air ratchet with standard accessories 413 b. instruments and general shop outfit air impact wrench with standard accessories 414 b. instruments and general shop outfit anvil with stand 415 b. instruments and general shop outfit calliper inside with spring 416 b. instruments and general shop outfit callipers outside with spring 417 b. instruments and general shop outfit chain pulley block capacity with tripod stand 418 b. instruments and general shop outfit chisels cross cut 419 b. instruments and general shop outfit circlip pliers expanding and contracting 420 b. instruments and general shop outfit compression testing gauge suitable for diesel engine with standard accessories 421 b. instruments and general shop outfit connecting rod alignment fixture 422 b. instruments and general shop outfit copper bit soldering iron 423 b. instruments and general shop outfit cylinder liner dry & wet liner, press fit &slidefit liner 424 b. instruments and general shop outfit dc ohmmeter 425 b. instruments and general shop outfit dial gauge type 1 gr. a (complete with clamping devices and with magnetic stand) 426 b. instruments and general shop outfit dividers with spring 427 b. instruments and general shop outfit drift punch copper 428 b. instruments and general shop outfit drill point angle gauge 429 b. instruments and general shop outfit drill twist (various sizes) 430 b. instruments and general shop outfit electric soldering iron 431 b. instruments and general shop outfit electric testing screw driver 432 b. instruments and general shop outfit engineer’s square 433 b. instruments and general shop outfit feeler gauge 20 blades (metric) 434 b. instruments and general shop outfit file flat , bastard 435 b. instruments and general shop outfit file, half round ,second cut 436 b. instruments and general shop outfit file, square second cut 437 b. instruments and general shop outfit file, square round 438 b. instruments and general shop outfit file, triangular , second cut 439 b. instruments and general shop outfit flat file , second cut 440 b. instruments and general shop outfit flat file , bastard 441 b. instruments and general shop outfit fuel injection pump (diesel) inline 442 b. instruments and general shop outfit fuel injection pump dismantling tool kit/universal vice 443 b. instruments and general shop outfit fuel injection pump ve pump / distributor fuel rotary pump (dpc) pumps / along with special tools and accessories 444 b. instruments and general shop outfit gloves for welding 445 b. instruments and general shop outfit glow plug tester 446 b. instruments and general shop outfit granite surface plate with stand and cover 447 b. instruments and general shop outfit grease gun heavy duty trolley type 448 b. instruments and general shop outfit hammer chipping 449 b. instruments and general shop outfit hammer copper with handle 450 b. instruments and general shop outfit hand operated crimping tool 451 b. instruments and general shop outfit hand reamers adjustable 452 b. instruments and general shop outfit hand shear universal 453 b. instruments and general shop outfit hand vice 454 b. instruments and general shop outfit hollow punch set of seven pieces 455 b. instruments and general shop outfit injector – multi hole type, pintle type 456 b. instruments and general shop outfit injector cleaning unit 457 b. instruments and general shop outfit injector testing set (hand tester) 458 b. instruments and general shop outfit insulated screw driver 459 b. instruments and general shop outfit insulated screw driver 460 b. instruments and general shop outfit left cut snips 461 b. instruments and general shop outfit lifting jack screw 462 b. instruments and general shop outfit magneto spanner set with 8 spanners 463 b. instruments and general shop outfit multimeter digital 464 b. instruments and general shop outfit oil can 465 b. instruments and general shop outfit oil pump for dismantling and assembling. 466 b. instruments and general shop outfit oil stone 467 b. instruments and general shop outfit oscilloscope 468 b. instruments and general shop outfit philips screw driver set of 5 pieces 469 b. instruments and general shop outfit pipe cutting tool 470 b. instruments and general shop outfit pipe flaring tool 471 b. instruments and general shop outfit piston ring compressor 472 b. instruments and general shop outfit piston ring expander and remover. 473 b. instruments and general shop outfit piston ring groove cleaner. 474 b. instruments and general shop outfit pliers combination 475 b. instruments and general shop outfit pliers flat nose 476 b. instruments and general shop outfit pliers round nose 477 b. instruments and general shop outfit pliers side cutting 478 b. instruments and general shop outfit portable electric drill machine 479 b. instruments and general shop outfit prick punch 480 b. instruments and general shop outfit radiator cut section cross flow 481 b. instruments and general shop outfit radiator cut section down flow 482 b. instruments and general shop outfit radiator pressure cap 483 b. instruments and general shop outfit right cut snips 484 b. instruments and general shop outfit rivet sets snap and dolly combined 485 b. instruments and general shop outfit scraper flat 486 b. instruments and general shop outfit scraper half round 487 b. instruments and general shop outfit scraper triangular 488 b. instruments and general shop outfit scriber 489 b. instruments and general shop outfit scriber with scribing black universal 490 b. instruments and general shop outfit set of stock and dies metric 491 b. instruments and general shop outfit tinnman’s shear 492 b. instruments and general shop outfit sheet metal gauge 493 b. instruments and general shop outfit tinnman’sshear 494 b. instruments and general shop outfit soldering copper 495 b. instruments and general shop outfit solid parallels in pairs (different size) in metric 496 b. instruments and general shop outfit spanner clyburn 497 b. instruments and general shop outfit spanner t. flocks for screwing up and up screwing inaccessible 498 b. instruments and general shop outfit spanner, adjustable 499 b. instruments and general shop outfit spanner, ring set of 12 metric sizes 500 b. instruments and general shop outfit spark lighter 501 b. instruments and general shop outfit spark plug spanner 14mm x 18mm x size 502 b. instruments and general shop outfit starter motor axial type, pre engagement type & co axial type 503 b. instruments and general shop outfit steel measuring tape in a case 504 b. instruments and general shop outfit steel rule 505 b. instruments and general shop outfit steel rule 30 cm inch and metric 506 b. instruments and general shop outfit straight edge gauge 2 ft. 507 b. instruments and general shop outfit straight edge gauge 4 ft. 508 b. instruments and general shop outfit stud extractor set of 3 509 b. instruments and general shop outfit stud remover with socket handle 510 b. instruments and general shop outfit surface gauge with dial test indicator plunger type 511 b. instruments and general shop outfit tachometer (counting type) 512 b. instruments and general shop outfit tandem master cylinder with booster 513 b. instruments and general shop outfit taps and dies complete sets (5 types) 514 b. instruments and general shop outfit taps and wrenches metric 515 b. instruments and general shop outfit telescope gauge 516 b. instruments and general shop outfit temperature gauge with sensor 517 b. instruments and general shop outfit thermostat 518 b. instruments and general shop outfit thread pitch gauge metric 519 b. instruments and general shop outfit timing lighter 520 b. instruments and general shop outfit torque wrenches 521 b. instruments and general shop outfit turbocharger cut sectional view 522 b. instruments and general shop outfit tyre pressure gauge with holding nipple 523 b. instruments and general shop outfit universal puller for removing pulleys, bearings 524 b. instruments and general shop outfit v’ block 75 x 38 mm pair with clamps 525 b. instruments and general shop outfit vacuum gauge 526 b. instruments and general shop outfit valve lifter 527 b. instruments and general shop outfit valve spring compressor universal 528 b. instruments and general shop outfit vernier calliper 529 b. instruments and general shop outfit vice grip pliers 530 b. instruments and general shop outfit water pump for dismantling and assembling 531 b. instruments and general shop outfit wire gauge (metric ) 532 b. tools, instruments and general shop outfit allen key set of 12 pieces 533 b. tools, instruments and general shop outfit alternator for tractor different type 534 b. tools, instruments and general shop outfit ammeter 535 b. tools, instruments and general shop outfit angle plate adjustable 536 b. tools, instruments and general shop outfit angle plate 537 b. tools, instruments and general shop outfit anvil 50 kgs with stand 538 b. tools, instruments and general shop outfit arbor press hand operated 539 b. tools, instruments and general shop outfit battery charger 540 b. tools, instruments and general shop outfit caliper inside 541 b. tools, instruments and general shop outfit calipers outside 542 b. tools, instruments and general shop outfit chain pulley block 3 ton capacity with tripod stand 543 b. tools, instruments and general shop outfit chaser hard w/v 9 to 40 t.p.i. set of 11 external. 544 b. tools, instruments and general shop outfit chaser, hand w/w 9 to 40 t.p.i. set of 11 internal 545 b. tools, instruments and general shop outfit chisel 546 b. tools, instruments and general shop outfit circlip pliers expanding and contracting type 547 b. tools, instruments and general shop outfit clamps c 548 b. tools, instruments and general shop outfit clamps c 549 b. tools, instruments and general shop outfit clamps c 550 b. tools, instruments and general shop outfit compression testing gauge suitable for diesel engine 551 b. tools, instruments and general shop outfit connecting rod alignment fixture 1 552 b. tools, instruments and general shop outfit cut section model of fuel filter 553 b. tools, instruments and general shop outfit cylinder liner dry & wet liner, press fit & slidefit liner 554 b. tools, instruments and general shop outfit dial gauge type 1 gr. a (completewith clamping devices and stand) 555 b. tools, instruments and general shop outfit different type of engine bearing model 556 b. tools, instruments and general shop outfit dividers 557 b. tools, instruments and general shop outfit drift, copper 558 b. tools, instruments and general shop outfit drill twist 559 b. tools, instruments and general shop outfit electric soldering 560 b. tools, instruments and general shop outfit engineers square 561 b. tools, instruments and general shop outfit feeler gauge 562 b. tools, instruments and general shop outfit file flat 563 b. tools, instruments and general shop outfit file, half round 564 b. tools, instruments and general shop outfit file, square 565 b. tools, instruments and general shop outfit file, square 566 b. tools, instruments and general shop outfit file, triangular 567 b. tools, instruments and general shop outfit files assorted sizes and types including safe edge file (20 nos) 568 b. tools, instruments and general shop outfit flat file 569 b. tools, instruments and general shop outfit granite surface plate 570 b. tools, instruments and general shop outfit grover 571 b. tools, instruments and general shop outfit hacksaw frame adjustable 572 b. tools, instruments and general shop outfit hammer ball peen 573 b. tools, instruments and general shop outfit hammer copper 574 b. tools, instruments and general shop outfit hand operated crimping tool (i) forcrimping up to 4mm and (ii) for crimping up to 10mm 575 b. tools, instruments and general shop outfit hydraulic jack hi lift type 576 b. tools, instruments and general shop outfit injector multi hole type, pintle type 577 b. tools, instruments and general shop outfit lifting jack screw type 578 b. tools, instruments and general shop outfit magneto spanner set with 579 b. tools, instruments and general shop outfit magnifying glass 580 b. tools, instruments and general shop outfit marking out table 581 b. tools, instruments and general shop outfit multi scan tool 582 b. tools, instruments and general shop outfit philips screwdriver set of 5 pieces 583 b. tools, instruments and general shop outfit portable oil monitoring indicator 584 b. tools, instruments and general shop outfit power supply 585 b. tools, instruments and general shop outfit punch letter 586 b. tools, instruments and general shop outfit rear axle assembly gear box steering box assembly of the diesel engine 587 b. tools, instruments and general shop outfit ridger. 588 b. tools, instruments and general shop outfit set of stock and dies unc, unfand metric 589 b. tools, instruments and general shop outfit soldering copper hatchet type 590 b. tools, instruments and general shop outfit spanner t. flocks for screwing up and up screwing inaccessible positions 591 b. tools, instruments and general shop outfit spanners socket with speed handle, t bar, ratchet and universal upto 32 mm set of 28pieces with box 592 b. tools, instruments and general shop outfit spirit level 593 b. tools, instruments and general shop outfit stake grooving. 594 b. tools, instruments and general shop outfit stake, hatchet. 595 b. tools, instruments and general shop outfit starter motor for tractor different type 596 b. tools, instruments and general shop outfit steel measuring tape 10 meter in a case 597 b. tools, instruments and general shop outfit steel rule 598 b. tools, instruments and general shop outfit steel wire brush 599 b. tools, instruments and general shop outfit stone, carborandum 600 b. tools, instruments and general shop outfit straight edge gauge 601 b. tools, instruments and general shop outfit straight edge gauge 602 b. tools, instruments and general shop outfit temperature gauge 603 b. tools, instruments and general shop outfit thread pitch gauge metric, bsw 604 b. tools, instruments and general shop outfit trammel 30 cm 605 b. tools, instruments and general shop outfit v block 606 b. tools, instruments and general shop outfit vacuum gauge to read 607 b. tools, instruments and general shop outfit valve spring compressor universal. 608 b. tools, instruments and general shop outfit voltmeter 609 b. tools, instruments and general shop outfit wing compass 610 b. instruments and general shop outfit surface plate granite 611 b. instruments and general shop outfit bench vice 612 b. instruments and general shop outfit v block 613 b. instruments and general shop outfit universal surface gauge 614 b. instruments and general shop outfit chisel cold flat 615 b. instruments and general shop outfit hammer copper/brass 616 b. instruments and general shop outfit hacksaw fixed 617 b. instruments and general shop outfit file flat 618 b. instruments and general shop outfit file flat 619 b. instruments and general shop outfit file flat 620 b. instruments and general shop outfit file half round 621 b. instruments and general shop outfit file round 622 b. instruments and general shop outfit file half round 623 b. instruments and general shop outfit knurling tool revolving head 624 b. instruments and general shop outfit combination set 625 b. instruments and general shop outfit screwdriver 626 b. instruments and general shop outfit spanner double ended 627 b. instruments and general shop outfit spanner adjustable 628 b. instruments and general shop outfit pliers flat nose 629 b. instruments and general shop outfit caliper transfer inside 630 b. instruments and general shop outfit micrometer inside 631 b. instruments and general shop outfit micrometer inside 632 b. instruments and general shop outfit depth gauge micrometer 633 b. instruments and general shop outfit vernier caliper outside, inside and depth 634 b. instruments and general shop outfit dial vernier caliper with metric 635 b. instruments and general shop outfit vernier bevel protractor 636 b. instruments and general shop outfit vernier micrometer 637 b. instruments and general shop outfit vernier micrometer 638 b. instruments and general shop outfit gauge feeler 639 b. instruments and general shop outfit gauge radius set 640 b. instruments and general shop outfit centre gauge 641 b. instruments and general shop outfit screw pitch gauge 642 b. instruments and general shop outfit drill angle gauge 643 b. instruments and general shop outfit universal dial test indicator plunger type 644 b. instruments and general shop outfit vernier height gauge 645 b. instruments and general shop outfit try square 646 b. instruments and general shop outfit plain ring and plug gauge 647 b. instruments and general shop outfit wheel dresser hunting on type withstar cutter 648 b. instruments and general shop outfit wheel dresser diamond 649 b. instruments and general shop outfit screw thread micrometerinterchangeable 650 b. instruments and general shop outfit morse taper plug & ring gauge 651 b. instruments and general shop outfit sine bar with centers 652 b. instruments and general shop outfit slip gauge metric set 653 b. instruments and general shop outfit morse taper 654 b. instruments and general shop outfit twist drill 655 b. instruments and general shop outfit drill twist set 656 b. instruments and general shop outfit drill chuck 657 b. instruments and general shop outfit tap & die 658 b. instruments and general shop outfit tap and die set 659 b. instruments and general shop outfit tap & die 660 b. instruments and general shop outfit tap & die 661 b. instruments and general shop outfit reamer machine 662 b. instruments and general shop outfit reamer adjustable 663 b. instruments and general shop outfit tool holder rh & straight for mmsquare tool bit 664 b. instruments and general shop outfit parting tool holder with h.s.s. blade 665 b. instruments and general shop outfit tool bits 666 b. instruments and general shop outfit boring tool holder 667 b. instruments and general shop outfit oil can 668 b. instruments and general shop outfit dog carrier 669 b. instruments and general shop outfit angle plate 670 b. instruments and general shop outfit combination drill / centre drill 671 b. instruments and general shop outfit oil stone 672 b. instruments and general shop outfit tap wrench (adjustable) 673 b. instruments and general shop outfit die and wrench 674 b. instruments and general shop outfit tool bit assorted sizes on holder 675 b. instruments and general shop outfit machine vice swivel base 676 b. instruments and general shop outfit spare grinding wheel ajax type forcarbide tool 677 b. instruments and general shop outfit angle gauge for tool grinding 678 b. instruments and general shop outfit hand chaser 679 b. instruments and general shop outfit hand chaser 680 b. instruments and general shop outfit revolving center (to suit lathetailstock) 681 b. instruments and general shop outfit tool cemented carbide assorted shaped(external) for steel turning 682 b. instruments and general shop outfit thread plug gauge 683 b. instruments and general shop outfit thread ring gauge 684 b. instruments and general shop outfit machine chaser 685 b. instruments and general shop outfit coventry die head 686 b. instruments and general shop outfit gauge drill grinding 687 b. instruments and general shop outfit magnetic chuck 688 b. instruments and general shop outfit lathe mandrels (diff. types) 689 b. instruments and general shop outfit coventry type die head (self opening) 690 b. instruments and general shop outfit collapsible tap with attachment 691 b. instruments and general shop outfit bore dial gauge stems 692 b. instruments and general shop outfit spindle key 693 b. instruments and general shop outfit screw driver 694 b. instruments and general shop outfit number punch 695 b. instruments and general shop outfit letter punch 696 b. instruments and general shop outfit magnifying glass 697 b. instruments and general shop outfit universal weld measuring gauge 698 b. instruments and general shop outfit spanner d.e. 699 b. instruments and general shop outfit c clamps 700 b. instruments and general shop outfit hammer sledge 701 b. instruments and general shop outfit h.p. welding torch 702 b. instruments and general shop outfit oxygen gas pressure 703 b. instruments and general shop outfit acetylene gas pressure 704 b. instruments and general shop outfit co2 gas pressure regulator 705 b. instruments and general shop outfit argon gas pressure regulator 706 b. instrument and general shop outfit surface plate 707 b. instrument and general shop outfit oil can 708 b. instrument and general shop outfit surface gauge universal 709 b. instrument and general shop outfit bench vice 710 b. instrument and general shop outfit hack saw tubular metal frameadjustable 711 b. instrument and general shop outfit snip sheet metal straight nose 712 b. instrument and general shop outfit snip sheet metal curved nose 713 b. instrument and general shop outfit anvil 714 b. instrument and general shop outfit stakes [ different types] 715 b. instrument and general shop outfit tin smith 716 b. instrument and general shop outfit wooden mallet /nylon mallet 717 b. instrument and general shop outfit round punch 718 b. instrument and general shop outfit electrical drill portable drillwith chuck and key 719 b. instrument and general shop outfit screw driver, plastic handle, 720 b. instrument and general shop outfit screw driver, plastic handle,flat tip 721 b. instrument and general shop outfit philips screw driver 722 b. instrument and general shop outfit screw driver, plastic handle,flat tip 723 b. instrument and general shop outfit soldering iron exchangeablecopper tip 724 b. instrument and general shop outfit knife folded stainless steel 725 b. instrument and general shop outfit tong tester (clamp on multimeter) 726 b. instrument and general shop outfit tenon saw 727 b. instrument and general shop outfit firmer chisel 728 b. instrument and general shop outfit rawal plug tool 729 b. instrument and general shop outfit fire extinguisher 730 b. instrument and general shop outfit fire buckets 731 b. instrument and general shop outfit d.e spanner 732 b. instrument and general shop outfit ring spanner 733 b. instrument and general shop outfit quick couples, process tubeadopter 734 b. instrument and general shop outfit tong close mouth and pick 735 b. instrument and general shop outfit welding table for gas/arc 736 b. instrument and general shop outfit flaring tool set, single type fortube. 737 b. instrument and general shop outfit swaging tool, punch type, setof size for tube. 738 b. instrument and general shop outfit bending spring external type,for copper tube 739 b. instrument and general shop outfit pipe cutter miniature forcopper tube 740 b. instrument and general shop outfit pinch of tool, for copper tube, 741 b. instrument and general shop outfit ratchet spanner 742 b. instrument and general shop outfit capillary plug gauge 743 b. instrument and general shop outfit piercing pliers & reversing valvewith access fitting 744 b. instrument and general shop outfit spanner double ended 745 b. instrument and general shop outfit ring spanner off set 746 b. instrument and general shop outfit wrench adjustable 747 b. instrument and general shop outfit wrench adjustable 748 b. instrument and general shop outfit wrench adjustable 749 b. instrument and general shop outfit valve key handle[treated asconsumable] 750 b. instrument and general shop outfit (hollo) punch hole for cuttinggasket 751 b. instrument and general shop outfit scissor, gasket cutting stainlesssteel 752 b. instrument and general shop outfit l allen key 753 b. instrument and general shop outfit t allen key set 754 b. instrument and general shop outfit pipe cutter with built in reamerand space cutter, for copper tube 755 b. instrument and general shop outfit pipe /tube bender lever type 756 b. instrument and general shop outfit spanner double ended 757 b. instrument and general shop outfit pipe wrench 758 b. instrument and general shop outfit lapping plate 759 b. instrument and general shop outfit hammer ball peen 760 b. instrument and general shop outfit puller 3 legged with flexiblearm 761 b. instrument and general shop outfit hand blower portablecomplete 762 b. instrument and general shop outfit spirit level precision metallic 763 b. instrument and general shop outfit tap set with matching drills 764 b. instrument and general shop outfit tap set with matching drills 765 b. instrument and general shop outfit refrigerant cylinder 766 b. instrument and general shop outfit heating kit with infrared bulb 767 b. instrument and general shop outfit plumbing hammer weight 768 b. instrument and general shop outfit cylinder 134 a 769 b. instrument and general shop outfit torque wrench 770 b. instrument and general shop outfit piercing valve 771 b. instrument and general shop outfit feeler gauge 772 b. instrument and general shop outfit four way reversible valve 773 b. instrument and general shop outfit vernier height gauge 774 b. instrument and general shop outfit tape measuring graduation in mm 775 b. instrument and general shop outfit voltmeter, ac/dc portable precision grade digital panel board type 776 b. instrument and general shop outfit ammeter, ac/dc portable precision grade digital panel board type 777 b. instrument and general shop outfit megger 778 b. instrument and general shop outfit wattmeter multi range up 779 b. instrument and general shop outfit multi meter digital type 780 b. instrument and general shop outfit k.w. meter 781 b. instrument and general shop outfit service oscillator 782 b. instrument and general shop outfit c.r.o single beam 783 b. instrument and general shop outfit c.r.o dual trace/ double beam 784 b. instrument and general shop outfit a.f.o oscillators 785 b. instrument and general shop outfit pressure gauge digital type 786 b. instrument and general shop outfit compound digital type gauge, 787 b. instrument and general shop outfit service man metal case thermometer 788 b. instrument and general shop outfit gas leak detector for halogen gas 789 b. instrument and general shop outfit electronic leak detector 790 b. instrument and general shop outfit sling psychrometer mounted on aluminum back, 791 b. instrument and general shop outfit stop watch 792 b. instrument and general shop outfit vernier caliper 793 b. instrument and general shop outfit micrometer outside measurement 794 b. instrument and general shop outfit multi meter analogue type 795 b. instrument and general shop outfit tachometer digital, multi range 796 b. instrument and general shop outfit micron vacuum gauge 797 b. instrument and general shop outfit sensor thermometer (digital) 798 b. instrument and general shop outfit fin straightened/fin comb. 799 b. instrument and general shop outfit filler gauge 800 b. instrument and general shop outfit wire gauge metric & british. 801 b. instrument and general shop outfit dial thermometer remote control, armored capillary dial 802 b. instrument and general shop outfit anemometer 803 b. instrument and general shop outfit compressors testers for small hermetic compressors 804 b. instrument and general shop outfit digital thermometer 805 b. instrument and general shop outfit temperature &humidity recorder 806 b. instrument and general shop outfit instrumentation screw driver set 807 b. instrument and general shop outfit digital weighing machine 808 b. instrument and general shop outfit split phase induction motor 809 b. instrument and general shop outfit bldc motor with controller 810 b. instrument and general shop outfit idu pulse motor 811 b. instrument and general shop outfit capacitor start induction motor 812 b. instrument and general shop outfit ac 3 phase motor, 400/50 hz 813 b. instrument and general shop outfit star delta starter 814 b. instrument and general shop outfit auto transformer starter 815 b. instrument and general shop outfit d.o.l starter 816 b. instrument and general shop outfit portable air lpg brazing kit 817 b. instrument and general shop outfit oxy acetylene complete 818 b. instrument and general shop outfit single door direct cool refrigerator, carrying with hfcand hc 819 b. instrument and general shop outfit frost free refrigerator 820 b. instrument and general shop outfit three/four door refrigerator ( inverter type) 821 b. instrument and general shop outfit core drill machine. 822 b. instrument and general shop outfit bench drilling machine 823 b. instrument and general shop outfit grinding machine 824 b. instrument and general shop outfit evacuating and refrigerant charging station, consist ofa) rotary two stage vacuum pump and motor (with gas ballast and anti such back)b) manifold with gauges and valves and capable of pulling vacuum up to 50 microns of hg and with provision of connecting to a microns level vacuum gaugeb) graduated charging cylinder with provision for temperature correction and all necessaryisolating valves 825 b. instrument and general shop outfit evacuating and charging station as above but fitted with weighing scale 826 b. instrument and general shop outfit two stage rotary vacuum pump,3or 4 cfm. 827 b. instrument and general shop outfit dry n2 cylinder 828 b. instrument and general shop outfit window a.c 829 b. instrument and general shop outfit split a.c 830 b. instrument and general shop outfit duct able split a.c 1.5 ton 831 b. instrument and general shop outfit recovery unit with cylinders 832 b. instrument and general shop outfit decibel meter 833 b. instrument and general shop outfit cassette air conditioner 834 b. instrument and general shop outfit de scaling pump set 835 b. instrument and general shop outfit fan coil unit 836 b. instrument and general shop outfit shell and tube, (small) 837 b. instrument and general shop outfit circulating water pump (small) 838 b. instrument and general shop outfit refrigerant cylinder 839 b. instrument and general shop outfit gauge manifold with gauges 840 b. instrument and general shop outfit shell and tube type condenser 841 b. instrument and general shop outfit rotary hermetic compressor 842 b. instrument and general shop outfit bottle cooler visible 843 b. instrument and general shop outfit deep freezer 844 b. instrument and general shop outfit display cabinet 845 b. instrument and general shop outfit water cooler storage type 846 b. instrument and general shop outfit water dispenser (hot and cold) 847 b. instrument and general shop outfit ice candy plant 848 b. instrument and general shop outfit air conditioning, direct system. 849 b. instrument and general shop outfit air conditioning, indirect system. (water cooled ) 850 b. instrument and general shop outfit package a/c 851 b. instrument and general shop outfit car a.c components (full kit)a) wobble plate compressor with mounting brackets.b) serpentine evaporatorc) parallel flow condenserd) hoses, tubes, receiver, ex.valve.e) electrical components &wiring harness 852 b. instrument and general shop outfit car ac tutorial model 853 b. instrument and general shop outfit bus ac tutorial model 854 b. instrument and general shop outfit automatic ice cube m/c 855 b. instrument and general shop outfit storage type water cooler (hot and cold) 856 b. instrument and general shop outfit vrf/vrv unit with two indoor units 2.5tr each and 5tr capacity out door unit complete with air cooled condenser,accessories and controls. 857 b. instrument and general shop outfit split a/c (inverter technology) 858 b. instrument and general shop outfit walk in cooler puf insulated for cold room 6x4.5x8 cft. 859 b. instrument and general shop outfit absorption system 860 b. tools, measuring instruments and general shop outfit try square 861 b. tools, measuring instruments and general shop outfit inside caliper 862 b. tools, measuring instruments and general shop outfit caliper outside 863 b. tools, measuring instruments and general shop outfit odd leg caliper 864 b. tools, measuring instruments and general shop outfit soil pot with brush 865 b. tools, measuring instruments and general shop outfit d. e. spanners 866 b. tools, measuring instruments and general shop outfit plumbers metal melting pot 867 b. tools, measuring instruments and general shop outfit pipe stock and dies complete with stocks,bushing, bushing holders, taps and wrenches sizes covered, to suit pipes 868 b. tools, measuring instruments and general shop outfit pipe vice 869 b. tools, measuring instruments and general shop outfit stillson pattern pipe wrenches 870 b. tools, measuring instruments and general shop outfit stillson pattern pipe wrenches 871 b. tools, measuring instruments and general shop outfit chain :pipe wrench 872 b. tools, measuring instruments and general shop outfit adjustable, spanner, a 375, is 6149 873 b. tools, measuring instruments and general shop outfit pipe bender, manually operated 874 b. tools, measuring instruments and general shop outfit leg vice, 75mm jaw on stand is 2588 875 b. tools, measuring instruments and general shop outfit hand drill 6mm capacity with drill chuck(electric) 876 b. tools, measuring instruments and general shop outfit drill twist (straight shank) 877 b. tools, measuring instruments and general shop outfit electric pump 878 b. tools, measuring instruments and general shop outfit hydraulic pressure machine for testingleakage in gi pipe fittings etc. 879 b. tools, measuring instruments and general shop outfit pipe bender (hydraulic type) 880 b. tools, measuring instruments and general shop outfit chase cutter (electric) 881 b. instruments and general shop outfit air impact wrench with standard accessories 882 b. instruments and general shop outfit air ratchet with standard accessories 883 b. instruments and general shop outfit ammeter 884 b. instruments and general shop outfit angle plate 885 b. instruments and general shop outfit battery –charger 886 b. instruments and general shop outfit blow lamp 887 b. instruments and general shop outfit bucket, sponge, squeegee, chamois & tack rags 888 b. instruments and general shop outfit colour matching cards /panels (magnetic, chromalux card orprimed metal) 889 b. instruments and general shop outfit copper bit soldering iron 890 b. instruments and general shop outfit cylinder bore gauge capacity 891 b. instruments and general shop outfit depth micrometer 892 b. instruments and general shop outfit dial gauge type 1 gr. a(complete with clamping devices and stand) 893 b. instruments and general shop outfit dividers 894 b. instruments and general shop outfit engineers square 895 b. instruments and general shop outfit files assorted sizes and types including safe edge file (20nos) 896 b. instruments and general shop outfit garage rack 897 b. instruments and general shop outfit hand shear universal 898 b. instruments and general shop outfit lifting jack screw type 899 b. instruments and general shop outfit multimeter digital 900 b. instruments and general shop outfit outside micrometer 901 b. instruments and general shop outfit outside micrometer 902 b. instruments and general shop outfit paint measuring / mixing stick& jug sets 903 b. instruments and general shop outfit panel buffing machine 904 b. instruments and general shop outfit set of stock and dies metric 905 b. instruments and general shop outfit shertinmans 906 b. instruments and general shop outfit spirit level 907 b. instruments and general shop outfit taps and wrenches metric 908 b. instruments and general shop outfit trammel 909 b. instruments and general shop outfit v block 910 b. instruments and general shop outfit verniercaliper 911 b. instruments and general shop outfit voltmeter 912 c. general installation/ machineries angle grinder 913 c. general installation/ machineries belt sander (narrow surface) 914 c. general installation/ machineries body shell for painting light motor vehicle of different manufactures 915 c. general installation/ machineries compressed air line 916 c. general installation/ machineries die grinding kit 917 c. general installation/ machineries disc sander 918 c. general installation/ machineries drilling machine bench to drill up to 12mm dia along withaccessories 919 c. general installation/ machineries dust extraction connections (vacuum) 920 c. general installation/ machineries motor vehicle suitable for body painting light motor vehicle of different 921 c. general installation/ machineries paint surface film thickness gauge (electronic) 922 c. general installation/ machineries random /dual action orbital sander 923 c. general installation/ machineries spray gun & mixing equipment cleaning machine(explosionproof) & bench 924 g. list of tools & accessories for pneumatics and hydraulics compressor unit 925 g. list of tools & accessories for pneumatics and hydraulics pneumatic trainer kit, each consisting ofthe following matching components and accessories: g. list of tools & accessories for pneumatics and hydraulics i. single acting cylinder g. list of tools & accessories for pneumatics and hydraulics ii. double acting cylinder g. list of tools & accessories for pneumatics and hydraulics iii. 3/2 way valve g. list of tools & accessories for pneumatics and hydraulics iv. 3/2 way valve g. list of tools & accessories for pneumatics and hydraulics v. one way flow control valve g. list of tools & accessories for pneumatics and hydraulics vi. 5/2 way valve g. list of tools & accessories for pneumatics and hydraulics vii. 5/2 way valve g. list of tools & accessories for pneumatics and hydraulics viii. 5/2 way pneumatic actuatedvalve g. list of tools & accessories for pneumatics and hydraulics ix. 3/2 way roller lever valve g. list of tools & accessories for pneumatics and hydraulics x. shuttle valve (or) g. list of tools & accessories for pneumatics and hydraulics xi. two pressure valve (and) g. list of tools & accessories for pneumatics and hydraulics xii. pressure gauge g. list of tools & accessories for pneumatics and hydraulics xiii. manifold with self closing g. list of tools & accessories for pneumatics and hydraulics xiv. pushbutton station for electrical signal input g. list of tools & accessories for pneumatics and hydraulics xv. relay station g. list of tools & accessories for pneumatics and hydraulics xvi. 3/2 way single solenoid valve g. list of tools & accessories for pneumatics and hydraulics xvii. 5/2 way single solenoid valve g. list of tools & accessories for pneumatics and hydraulics xviii. 5/2 way double solenoid valve g. list of tools & accessories for pneumatics and hydraulics xix. power supply unit, g. list of tools & accessories for pneumatics and hydraulics xx. profile plate, anodised aluminium 926 g. list of tools & accessories for pneumatics and hydraulics pneumatic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: 927 g. list of tools & accessories for pneumatics and hydraulics carrier for mounting components, such as pb & relay boxes. 928 g. list of tools & accessories for pneumatics and hydraulics cut section model for pneumaticcomponents 929 g. list of tools & accessories for pneumatics and hydraulics hydraulic trainer kit, each consisting of the following matching components and accessories: g. list of tools & accessories for pneumatics and hydraulics i. hydraulic power pack g. list of tools & accessories for pneumatics and hydraulics ii. pressure relief valve g. list of tools & accessories for pneumatics and hydraulics iii. drip tray, steel g. list of tools & accessories for pneumatics and hydraulics iv. pressure gauge g. list of tools & accessories for pneumatics and hydraulics v. four way distributor g. list of tools & accessories for pneumatics and hydraulics vi. double acting hydraulic cylinder g. list of tools & accessories for pneumatics and hydraulics vii. suitable weight g. list of tools & accessories for pneumatics and hydraulics viii. mounting kit for weight g. list of tools & accessories for pneumatics and hydraulics ix. 3/2 way directional control valve g. list of tools & accessories for pneumatics and hydraulics x. 4/2 way directional control valve g. list of tools & accessories for pneumatics and hydraulics xi. 4/3 way directional control valve g. list of tools & accessories for pneumatics and hydraulics xii. non return valve. g. list of tools & accessories for pneumatics and hydraulics xiii. pilot operated check valve g. list of tools & accessories for pneumatics and hydraulics xiv. one way flow control valve g. list of tools & accessories for pneumatics and hydraulics xv. t connector with self sealing coupling nipples (2 nos.) and quick coupling socket (1 no.). g. list of tools & accessories for pneumatics and hydraulics xvi. profile plate, 930 g. list of tools & accessories for pneumatics and hydraulics hydraulic workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: 931 g. list of tools & accessories for pneumatics and hydraulics cut section models for hydraulic components 932 general shop outfit surface plate c.i/granite with stand and cover 933 general shop outfit marking table (mild steel) 934 general shop outfit pipe bender machine spool type with stand manually operated. 935 general shop outfit angle plate 936 general shop outfit machine vice swivel base 937 general shop outfit machine vice swivel base 938 general shop outfit torque wrench (standard/ratchet type) 939 general shop outfit power tools for fastening 940 general shop outfit temperature gauge 941 general shop outfit lapping plate 942 general shop outfit anvil 24 sq. inches working area with stand 943 general shop outfit swage block 944 general shop outfit portable abrasive cut off machine 945 general shop outfit fuel injection test bench for calibration of fuel pump 946 general shop outfit electrical test bench 947 d. measuring instruments micrometer outside 948 d. measuring instruments micrometer outside 949 d. measuring instruments micrometer outside 950 d. measuring instruments micrometer outside ...

Indian Army - Bihar

46182126 bids are invited for cp pillar cock 15 mm fancy type , cp wash hand basin mixture 15 mm , cp shower rose 15mm , cp bib cock 15 mm fancy type , glass pane 4 feet x 3 feet x 3 mm plain , cp bib cock 15 mm long body , cp stop cock 15 mm , kitchen plate rack stainless steel 85 inch x 75 inch , cp towel rail 600 mm long , kitchen stand s steel size 775 mm height 750 mm width 250 mm depth , glass pane 2 feet x 3 feet x 3 mm plain , cp wall mixer with crunnch 15 mm , flushing cistern low level of 10 ltr capacity pvc , cp telephonic health faucet with pvc pipe 1.5 mtr , sliding bolt brass 300 milimeter long with nut and bolt , cp shower rose 15 x 150 mm , angle stop cock 15mm , looking mirror 24 inch x 18 inch x 3mm of plastic moulded panel , cp soap dish fancy type , wire mesh width 1200 mm length 15 mtr 0.47 mm , sliding bolt brass 250 mm with nut and bolt , sliding door bolt aluminium 300 mm , cp angle stop cock 15 mm two way , float valve 20 mm complete , cp angle cock 15 mm with flange , cp angle stop cock 15 mm , float valve complete 25 mm , angle cock cp long body 15 mm , plastic seat cover for ews colour white , bib cock ptmt long body 15mm , cp stop cock 15mm external thread , cp bib cock 15mm short body , m seal small packet , looking mirror 24 inch x 20 inch x 3 mm of plastic moulded panel , door handle aluminium 100 mm , glass shelve diplomat 600 mm , cp glass shelve diplomat 450 mm , door handle aluminium 125 mm , door stopper brass 5 inch , door handle aluminium 150 mm , bib cock pvc short body 15mm , spindle 15mm brass , cp jet spray , pvc waste pipe for wash band basin 1 mtr long , hydraulic door closer cast iron body designation no.2 universal type suitable for door shutters of 701 to 850 mm in width and weight between 36 to 60 kg , butt hinges ms 100 mm , pvc waste pipe for urinal 1 mtr long , gi nipple 15 x 100 mm , tower bolt aluminium 200mm , gi nipple 15 x 300 mm , gi nipple 15 x 150 mm , cp waste coupling 32 x 50 mm for stainless steel kitchen sink , door stopper aluminium double , helicol door spring 150 mm length , hydraulic door closer cast iron body designation no 3 universal type suitable for door shutters of 851 to 1000 mm in width and weight between 61 to 80 kg , bleaching powder , gi bend 15 x 150 mm , hydraulic door closer cast iron body designation no 1 universal type suitable for door shutters of upto 700 mm in width and weight between upto 35 kg , galvanised steel tubing 20 mm dia with socket , tower bolt aluminium 100 mm , grating stainless steel 100 mm dia , helicol door spring 125 mm length , helicol door spring 250 mm length , gi bend 15 mm dia , ms sliding door bolt 250 mm , gi reducers socket 20 x 15 mm , bow handle ms 125 mm , gi socket 15 mm , gi bend 15 x 100 mm , white portland cement with plastic packing of 1 kg wt each packet , door handle ms 100 mm , gi tubing 15 mm med gde , curtain rod stainless steel with brackets 20 mm , gi nipple 15 x 50 mm , gi bend 20 x 100 mm , tower bolt aluminium 150 mm , gi nipple 15 x 25 mm , cp grating 100 mm with 1 hole of waste pipe , gi tee equal 15 mm , oil putty for fixing of window glass , tee 15 mm , gi tee equal 20 mm , gi nipple 15 x 75 mm , curtain rod aluminium 20 mm , gi union socket 15 mm , hasp and staple aluminium 100 mm , nails wire 25 mm , gi socket 20 mm , sliding door bolt aluminium 200 mm , connection pipe pvc size 15 mm x 600 mm with coupling , gi reducing elbow 20 x 15 mm , bow handle aluminium 150 mm , door stopper aluminium single , cp rigid conduit pipe ms 15mm x 12 feet long for curtain , gi bend 20 x 150 mm , gi bend 20 mm dia , butt hinges ms 75 mm , gi elbow reducing 25 x 20 mm , gi elbow 20 mm dia , gi union 20 mm , hasp and staple aluminium 75 mm , gi elbow reducing 25 x 15 mm , gi elbow 15 mm dia , tower bolt 100 mm dia , gi nipple 20 x 300 mm , ms plug 15 mm , gi plug 15 mm dia , bow handle aluminium 75 mm , galvanised steel tubing 25 mm dia with socket , gi plug 20 mm dia , ms screw wood 50 mm , ms plug 20 mm , butt hinges ms 125 mm , ms screw wood 65 mm , gi nipple 20 mm 6 inch long , butt hinges ms 50 mm , nails wire 50 mm , hack saw blade double edge 300 mm , gi plug 25 mm dia , ms screw wood 15 mm , hasp and staple aluminium 50 mm , gi tee red 25x15 mm x 25 mm , hasp and stapple aluminium125 mm , ms screw wood 25 mm , ply wood 6 feet x 3 feet x 12 mm bwr gde as per is 303 , ms screw wood 20 mm , ms screw wood 45 mm , cp bkt for fixing of conduit pipe 15 mm , ms screw wood 35 mm , gi union socket 25 mm , gi tee reducing 25 x 15 mm , gi socket 25 mm , gi tee redg 25 x 20 mm x 25 mm , ms screw wood 75 mm total quantity : 2725...

East Central Railway - Bihar

46169377 auction sale of miscellaneous ferrous scrap(equalizing stay long pin, short pin, equalizing stay bracket, lh &rh bracket, nut & bolts, split pin, spring guide, anchor link bracket on bogie frame, flange for fixing shock absorber,levers, anchor link, brake block hanger, bss hanger pin, equalizing stay, hanger block (stone), adjuster for brake head spring, silent block brake head, protection tube, compensating ring etc.,i lot no 375985724017, location scrap yard...

Eastern Railways - Bihar

46126259 supply of bracket for distributor valve etc.bracket for distributor valve etc.,bracket for distributor valve as per rdsos drg. no. wd 80007 s 16, item no.3, alt no.13. [ warranty period: 30 months after the date of delivery ] [quantity tolerance (+/ ): 5 %age , item category : normal , total po value variation permitt ed: max 8 lacs ] ]...

Ministry Of Railways - Bihar

46088764 bids are invited for supply of various items as per annexure enclosed clearance gauge, spanner, size: 75/80/41, tunion bracket for lc (lh & rh), drum wheel for lc, wire adjustable screw, cylinder weights for lc gate, winch machine complete set with handle, pully state for lc gate total quantity : 1...

Building Division - Bihar

46043755 tender for supplying and installation of door closer, curtain rods, alluminium partition work and brackets....

Bihar State Power Transmission Company Limited - Bihar

46031866 procurement of opgw & its hardware fittings as spare for bsptcl 1 opgw 24 fiber 2 opgw 48 fiber 3 approach cable 24 fiber 4 approach cable 48 fiber 5 2 way joint box 24f 6 3 way joint box 24f 7 2 way joint box 48f 8 3 way joint box 48f 9 suspension assembly 10 tension assembly (single/joint box/passthrough) 11 downlead clamp 12 loop bracket 13 zero db coupling (square type) 14 zero db coupling (round type) 15 fc connector pigtail 16 patch chord (fcpc fcpc) 10 mtr 17 patch chord (fcpc lcpc) 10 mtr ...

Department Of Science And Technology - Bihar

46031822 request for proposal for supply of machine and equipments for consultancy works for civil engineering work at government polytechnic, muzaffarpur. 1 i.s. sieves 20 cm diameter brass apparatus size 80mm,63mm, 50mm,40mm,31.5mm, 25mm, 20mm, 16mm, 12.5 mm, 10 mm, 6.3 mm, 4.75 mm, 2.36mm, 1.18mm, 600 micron, 300 micron, 150 micron, 90 micron,75 micron as per is 460 2 hydrometer 3 plastic limit apparatus 4 liquid limit apparatus 5 shrinkage limit apparatus 6 pycnometer 7 pan for the determination of moisture content of soil 8 density bottle 9 standard proctors compaction (mdd) 10 heavy proctors (modified /mdd) 11 permeability (falling head and constant head test) 12 consolidation meter 13 core cutter 14 sand pouring cylinder 15 infra red moisture meter 16 laboratory hot air oven 17 plate load test apparatus 18 electronic balance 19 sieve shaker 20 glass measuring cylinder 21 digital stopwatch 22 cbr apparatus 23 standard penetration test apparatus (spt n value test apparatus) 1 measuring glass 1 abrasion charge for los angeles abrasion test abrasion charge cast iron or steel balls approximately 4.8 cm in diameter and each weighing between 300 to 445 grams. six to twelve balls are required 170 mm is sieve 12 balls 2 flakiness index apparatus standard thickness gauge confirming to is 2336 (part iv) 1 is sieves 63 mm, 50 mm, 40 mm, 31.5 mm, 25mm, 50 mm, 16 mm, 12.5mm ,10 mm, and 6.3 mm a balance of enough capacity and sensitivity it should have an accuracy of 0.1% of the weight of the test sample. 3 elongation index apparatus standard length gauge conforming the is 2386 (part 1) is sieve 63 mm, 50 mm, 40 mm, 31.5 mm, 25 mm, 20 mm, 16 mm,12.5mn, 10 mm, 6.3 mm 1 a balance of enough capacity and sensitivity it should have an accuracy of 0.1% of the weight of test sample a balance of enough capacity and sensitivity li should have an accuracy of 0 1% of the weight of lest sample 4 deleterious material test apparatus beaker 1 naoh solution sieve standard colour chart 5 soundness test apparatus as per standards specifications. 1 6 crushing value mould with all accessories as per standards specifications. 1 e. stone glazing and floor tiles test s.n. name of equipments specifications quantity unit price total amount (a) gst /tax amount gross amount (b) (c=a+b) 1 glazing test equipment as per standards specifications. 1 2 tile abrasion testing machine tile abrasion testing machine with thickness measuring device with dial gauge having 25 mm travel and 0.01 mm least count 1 ref. standard is:1237 & 1706 tile abrasion testing machine with thickness measuring device with dial gauge having 25 mm travel and 0.01 mm least count. the tile sample is pressed under a specified load against a grinding path, strewn evenly with an abrasive powder, revolving at the rate of 30 ± 1 rpm. at the end of 100 revolutions of the disc, the second parallel side of the tile is subjected to wear an equal number of revolutions of the disc. the abrasion testing machine consists of a replaceable grinding path, fitted on to a disc rotating about its vertical axis. the rotating disc and the grinding path are enclosed by a circular tray. a bracket holds the specimen. the loading is by a counterbalanced lever. a funnel is provided to facilitate charging the grinding path with abrasive powder. digital counter has a memory retention facility. thickness measuring device for measuring the wear of the tile should also be supplied with the machine. supplied complete with automatic preset revolution counter and one 7.5 kg weight with abrasive powder and thickness measuring device. suitable for operation on 220 v, 50 hz, single phase, ac supply. 3 diamond tile cutter diamond tile cutter 1 rated input power: 1200 w no load speed: 12,000 rpm weight: 2.8 kg disc diameter: 110 mm 1 penetration test of bituminous material 2 softening point test apparatus 3 ductility test apparatus 4 flash  and fire point the apparatus 5 viscosity test apparatus 6 bitumen mix design (marshall method) 1 test tube 2 desiccator 3 bod bottle 4 porcelain dish (made of borosil) 5 measuring cylinder 6 beaker 7 filter paper (42 & 45 no.) 8 funnel 9 conical flask ...

Indian Army - Bihar

46025271 bids are invited for 950211 gasket c type reduction gearbox 950215 gasket e type gear box 265249 spark plug connector 297656 spark plug 850775 double gasket 0.5 mm head gasket 841781 capstain screw m6x10 956260 low presure hose gc 7,5x12,5 260657 rubber buffer 25x20xm6 831713 o ring din 3771 3,2x1,8 air screw ring 861184 float 938655 carburater piston spring 12,5/14 261625 sieve sleves 963697 needle jet 2,72 961043 jet needle 11 g2 929702 pin 830720 gasket float bracket 950730 o ring 2 point five into 1 point 5 963147 idle jet 867696 carburator socket 261705 float neddle valve vitan tip 831700 rubber ring 126x1,5x3,5 956140 low pressure hose 956240 oil tank assy 850540 o ring 83 into 2 850040 rubber ring 158,5x2,5x5 996848 coil kit 864292 ignition cable 180mm 850633 exhaust gasket 300058205 short block engine 582 963500 needle clip 261710 float needle clip 963167 adjustment screw 860425 rubber spacer 960445 grommet 881433 radiator set standered version 913848 cylinder head rotax 582 engine , total quantity : 418...

Indian Oil Corporation Limited - Bihar

46007081 supply of spares of rotork mov actuator at erpl barauni , item supply , centre column (complete with clutch assembly, resolver pcb drive) for iq 10 (iq mark 2) , centre column (complete with clutch assembly, resolver pcb drive) for iq 12 (iq mark 2) , centre column (complete with clutch assembly, resolver pcb drive) for iq 20 (iq mark 2) , resolver pcb assembly complete drive mechanism for iq 10 (iq mark 2) , resolver pcb assembly complete drive mechanism for iq 12 (iq mark 2) , resolver pcb assembly complete drive mechanism for iq 20 (iq mark 2) , worm shaft & worm wheel (complete with w/shaft retainer screws seals etc) for model no: iq10f10b4, 18 rpm, wd:3100 000(iq mark 2) , worm shaft & worm wheel (complete with w/shaft retainer screws seals etc) for model no: iq10f10b4, 24 rpm, wd:3000 000(iq mark 2) , worm shaft & worm wheel (complete with w/shaft retainer screws seals etc) for model no: iq10f10b4, 36 rpm, wd:3100 000(iq mark 2) , worm shaft & worm wheel (complete with w/shaft retainer screws seals etc) for model no: iq10f10b4, 96 rpm, wd:3100 000(iq mark 2) , worm shaft & worm wheel (complete with w/shaft retainer screws seals etc) for model no: iq10nrb4, 48 rpm, wd:3100 000(iq mark 2) , worm shaft & worm wheel (complete with w/shaft retainer screws seals etc) for model no: iq12f10b4, 18 rpm, wd:3100 000(iq mark 2) , worm shaft & worm wheel (complete with w/shaft retainer screws seals etc) for model no: iq12f10b4, 24 rpm, wd:3100 000(iq mark 2) , worm shaft & worm wheel (complete with w/shaft retainer screws seals etc) for model no: iq12nrb4, 24 rpm, wd:3100 000(iq mark 2) , worm shaft & worm wheel (complete with w/shaft retainer screws seals etc) for model no: iq20f14a, 24 rpm, wd:3000 000(iq mark 2) , worm shaft & worm wheel (complete with w/shaft retainer screws seals etc) for model no: iq20 f14 b4, 18 rpm, wd:3000 000(iq mark 2) , torque transducer for model no: iq10f10b4, 18 rpm, wd:3100 000(iq mark 2) , torque transducer for model no: iq10f10b4, 24 rpm, wd:3000 000(iq mark 2) , torque transducer for model no: iq10f10b4, 36 rpm, wd:3100 000(iq mark 2) , torque transducer for model no: iq10f10b4, 96 rpm, wd:3100 000(iq mark 2) , torque transducer for model no: iq10nrb4, 48 rpm, wd:3100 000(iq mark 2) , torque transducer for model no: iq12f10b4, 18 rpm, wd:3100 000(iq mark 2) , torque transducer for model no: iq12f10b4, 24 rpm, wd:3100 000(iq mark 2) , torque transducer for model no: iq12nrb4, 24 rpm, wd:3100 000(iq mark 2) , torque transducer for model no: iq20f14a, 24 rpm, wd:3000 000(iq mark 2) , torque transducer for model no: iq20 f14 b4, 18 rpm, wd:3000 000(iq mark 2) , resolver pcb for all iq mark 2 actuators , battery for all iq mark 2 actuators , stator/rotor assembly (std paint & shade) for model no: iq10f10b4, 18 rpm, wd:3100 000(iq mark 2) , stator/rotor assembly (std paint & shade) for model no: iq10f10b4, 24 rpm, wd:3000 000(iq mark 2) , stator/rotor assembly (std paint & shade) for model no: iq10f10b4, 36 rpm, wd:3100 000(iq mark 2) , stator/rotor assembly (std paint & shade) for model no: iq10f10b4, 96 rpm, wd:3100 000(iq mark 2) , stator/rotor assembly (std paint & shade) for model no: iq10nrb4, 48 rpm, wd:3100 000(iq mark 2) , stator/rotor assembly (std paint & shade) for model no: iq12f10b4, 18 rpm, wd:3100 000(iq mark 2) , stator/rotor assembly (std paint & shade) for model no: iq12f10b4, 24 rpm, wd:3100 000(iq mark 2) , stator/rotor assembly (std paint & shade) for model no: iq12nrb4, 24 rpm, wd:3100 000(iq mark 2) , stator/rotor assembly (std paint & shade) for model no: iq20f14a, 24 rpm, wd:3000 000(iq mark 2) , stator/rotor assembly (std paint & shade) for model no: iq20 f14 b4, 18 rpm, wd:3000 000(iq mark 2) , electronics chasis assembly (3 phase supply, chasis, power card pcb & transformer)for iq 10 35 (iq mark 2) , contractor assembly (contactor & bracket) for iq 10 35 (iq mark 2) , contractor assembly (contactor & bracket) for iq 40 95 (iq mark 2) , main pcb (lcd, pcb, fixing ring, screws) programmed for all iq mark 2 actuators , terminal block assembly for all iq mark 2 actuators , comprehensive maintenance kit for iq 10 (iq mark 2) , comprehensive maintenance kit for iq 12 (iq mark 2) , comprehensive maintenance kit for iq 20 (iq mark 2) , local control pcb for all iq mark 2 actuators , l/s/r & o/c knob assembly for all iq mark 2 actuators , terminal cover (cover, screws, label) for all iq mark 2 actuators , resolver drive mechanism (complete with magnet, resolver pcb, oil seals etc) for iq 10 (iq mark 3) , resolver drive mechanism (complete with magnet, resolver pcb, oil seals etc) for iq 12 (iq mark 3) , resolver drive mechanism (complete with magnet, resolver pcb, oil seals etc) for iq 18 (iq mark 3) , resolver drive mechanism (complete with magnet, resolver pcb, oil seals etc) for iq 25 (iq mark 3) , torque transducer for model no: iq10f10b4, 36 rpm wd: 100b0010 (iq mark 3) , torque transducer for model no: iq10f10b4, 48 rpm wd: 100b0010 (iq mark 3) , torque transducer for model no: iq12f10b4, 48 rpm wd: 100b0010 (iq mark 3) , torque transducer for model no: iq12f10b4, 72 rpm wd: 100b0010 (iq mark 3) , torque transducer for model no: iq18f10b4, 36 rpm wd: 100b0010 (iq mark 3) , torque transducer for model no: iq18f10b4, 72 rpm wd: 100b0010 (iq mark 3) , torque transducer for model no: iq18f10b4, 96 rpm wd: 100b0010 (iq mark 3) , torque transducer for model no: iq25f14b4, 96 rpm wd: 100b0010 (iq mark 3) , torque transducer for model no: iq25f14b4, 192 rpm wd: 100b0010 (iq mark 3) , stator/rotor assembly (std paint & shade) for model no: iq10f10b4, 36 rpm wd: 100b0010 (iq mark 3) , stator/rotor assembly (std paint & shade) for model no: iq10f10b4, 48 rpm wd: 100b0010 (iq mark 3) , stator/rotor assembly (std paint & shade) for model no: iq12f10b4, 48 rpm wd: 100b0010 (iq mark 3) , stator/rotor assembly (std paint & shade) for model no: iq12f10b4, 72 rpm wd: 100b0010 (iq mark 3) , stator/rotor assembly (std paint & shade) for model no: iq18f10b4, 36 rpm wd: 100b0010 (iq mark 3) , stator/rotor assembly (std paint & shade) for model no: iq18f10b4, 72 rpm wd: 100b0010 (iq mark 3) , stator/rotor assembly (std paint & shade) for model no: iq18f10b4, 96 rpm wd: 100b0010 (iq mark 3) , stator/rotor assembly (std paint & shade) for model no: iq25f14b4, 96 rpm wd: 100b0010 (iq mark 3) , stator/rotor assembly (std paint & shade) for model no: iq25f14b4, 192 rpm wd: 100b0010 (iq mark 3) , electronics chassis assembly ( 3 phase supply, chassis, power pcb & transformer) for iq 10 35 (iq mark 3) , contractor assembly (contactor & bracket) for iq 10 35 (iq mark 3) , main pcb (lcd, pcb, fixing ring, screws) programmed for all iq mark 3 actuators , terminal bung, cable looms, watertight & explosion proof for all iq mark 3 actuators , comprehensive spares kit for iq 10 (iq mark 3) , comprehensive spares kit for iq 12 (iq mark 3) , comprehensive spares kit for iq 18 (iq mark 3) , comprehensive spares kit for iq 25 (iq mark 3) , hmi pcb assembly for all iq mark 3 actuators , l/s/r & o/c knob assembly for all iq mark 2 actuators for all iq mark 3 actuators , terminal cover (cover, screws, label) for all iq mark 3 actuators , centre column (b4 drive bush) for model no: iqd12f10b4, 36 rpm, wd:3000 000 (iq mark 2) , resolver pcb assembly complete drive mechanism for model no: iqd12f10b4, 36 rpm, wd:3000 000 (iq mark 2) , resolver pcb for model no: iqd12f10b4, 36 rpm, wd:3000 000 (iq mark 2) , chasis + power mod assy (dc) for model no: iqd12f10b4, 36 rpm, wd:3000 000 (iq mark 2) , main pcb for model no: iqd12f10b4, 36 rpm, wd:3000 000 (iq mark 2) , comprehensive maintenance kit for model no: iqd12f10b4, 36 rpm, wd:3000 000 (iq mark 2) , local control pcb for model no: iqd12f10b4, 36 rpm, wd:3000 000 (iq mark 2) , power supply 3 phase for rosov actuator model no: si 2.1 q61, 70 & 80 and sr. no. rs529901, rs521801, rs521802, rs5733, rs5734, rs391901/04 & rs394603/01 , power pcb (3 phase/24vdc) rosov actuator model no: si 2.1 q61, 70 & 80 and sr. no. rs529901, rs521801, rs521802, rs5733, rs5734, rs391901/04 & rs394603/01 , si pro main pcb rosov actuator model no: si 2.1 q61, 70 & 80 and sr. no. rs529901, rs521801, rs521802, rs5733, rs5734, rs391901/04 & rs394603/01 , rc250/rc260 – seal kit – std temp rosov actuator model no: si 2.1 q61 and sr. no. rs521801 & rs394603/01 , rc270/rc280 – seal kit – std temp rosov actuator model no: si 2.1 70 & 80 and sr. no. rs529901, rs521802, rs5733, rs5734 & rs391901/04...

Indian Oil Corporation Limited - Bihar

45996616 procurement of m/s ksb limited make spares , list of item(s) / work(s) as per tender documents , cvr,brg,pmp,p/n 360.01 02,ksb , slev,shft,pmp,p/n 523.12 , slev,shft,pmp,p/n 523.10 , pump comp. rotating assy, rphb 80 360/2 , slev,spacer,pmp,p/n 525.05 , ring,labyrinth,o.b.,pmp,p/n 423.01 , bracket,brg,o.b.,pmp,p/n 330.11 , bracket,brg,i.b.,pmp,p/n 330.12 , plate,diffuser,pmp,p/n 173 , comb gkt,rph ehm 250 630,p/n 411.10 , gaskets & o rings,rph 50 450...

East Central Railway - Bihar

45937722 supply of safety bracket assembly.safety bracket assembly.,safety bracket assembly with nut and bolt for mr,bp hose pipes. [ warranty period: 30 mo nths after the date of delivery ] ]...

Ministry Of Power - Bihar

45915479 bids are invited for 10. material po text: workshop_common, on basis of ntpc drg/ specs part name : cuplock ledger additional information : duty class: medium, size: 800 mm dimension : 40 mm. center to center of two vertical, actual size: 750 mm, outer diameter: 48.3 mm, steel tube manufactured as per is:1161 standards 20. material po text: workshop_common, on basis of ntpc drg/ specs part name : scaffold board material : steel dimension : 2450 x 250 mm 16g sheet, press bent with anti skid dimples, center to center of two omega transom:2500 without hook, mm, box type stiffeners 500 mm 30. material po text: workshop_common, on basis of ntpc drg / specs part name : scaffold board material : steel dimension : 1950 x 250 mm 16g sheet, press bent with anti skid dimples, without hook, center to center of two omega transom:2000 mm, box type stiffeners 500 mm 40. material po text: workshop equipment, oem / parts part name right angle coupler dimension :40x40 mm equipment manufacturer :bsl scaffolding limited for tube 40 nb (od 48mm x 48mm) [electro plated] 50. material po text: workshop_common, on basis of ntpc drg/specs part name : swivel coupler additional information : electroplated dimension : 40 x 40 mm for tube, forged 60. material po text: workshop_common, on basis of ntpc drg/ specs part name : hop up bracket additional information : reference: 3 board dimension : 800 mm total quantity : 3200...

Ministry Of Power - Bihar

45901072 bids are invited for led lights schedule 1 m8211010101 technical specifications : 10 w led batten tube light (2ft+/ 10%) 1. system power/wattage : 10 w 2. power factor : >0.95 3. cri (color rendering index) : >= 80 4. cct (correlated color temperature) : 5700 +/ ansi tolerance* 5. system efficacy : >100 lm/w 6. lumens output: wattage x system efficacy 7. ip (ingress protection): ip20 8. operating voltage : 230 v ac +/ bis tolerance 9. color designation cool day lamp 10. led tube integral batten type. 11. beam angle (nom) 120 ° 12. rohs (restriction of hazardous substances) rohs compliance 13. ce mark na 14. operating temperature : 0 50 deg c 15. housing material : plastic / glass/ polycarbonate 16. minimum impact protection: ik 02 17. surge protection device : 2.5kv 18. led chip efficacy : >135lm/w schedule 2 m8211010205 lamp,led technical specifications : 20 w led batten tube light 4ft. (1200mm +/ 10%) 1. system power/wattage : 20 w +/ 10% 2. power factor : >0.95 3. cri (color rendering index) : >= 80 4. cct (corelated color temperature) : 5700 +/ ansi tolerance* 5. system efficacy : >100 lm/w 6. lumens output: wattage x system efficacy 7. ip (ingress protection): ip20 8. operating voltage : 230 v ac +/ bis tolerance 9. color designation cool day lamp 10. led tube integral batten type. 11. beam angle (nom) 120 ° 12. rohs (restriction of hazardous substances) rohs compliance 13. operating temperature : 0 50 deg c 14. housing material : plastic / glass/polycarbonate 15. minimum impact protection: ik 02 16. surge protection device : 2.5kv 17. led chip efficacy : >135lm/w schedule 3 m8211011001 technical specifications : led bulb 9 w 1. system power/wattage : 9 w led bulb 2. power factor : >0.95 3. cri (color rendering index) : >= 80 4. cct (correlated color temperature) : 5700 +/ ansi tolerance* 5. system efficacy : >=100 lm/w 6. lumens output : wattage x system efficacy 7. ip (ingress protection): ip20 8. operating voltage : 230 v ac +/ bis tolerance 10. led bulb type : pin type (b22) 11. beam angle (nom) 120 ° 12. rohs (restriction of hazardous substances) rohs compliance 13. ce mark na 14. operating temperature : 0 50 deg c 15. housing material : plastic / glass 16. minimum impact protection: ik 02 17. surge protection device : 2.5kv 18. led chip efficacy : >135lm/w 19 life test/burning hours : 25000 hrs life with 70% lumens maintained schedule 4 m8225120680 technical specifications :led based street light fitting : 110w (minimum) 1. system power/wattage : 110 w +/ bis tolerance 2. power factor : > 0.95 3. cri ( color rendering index) : > 70 4. cct (correlated color temp) : 5700 k +/ ansi tolerance 5. surge protection device : 20 kv / 10ka a. internal >= 4 kv b. external external 10 ka, 20 kv 6. cable : as per manufacturer standard 7. ip (ingress protection) :ip 66 waterproof, dustproof, impact proof & corrosion proof features meeting requirement of outdoor application. ip66 8. input voltage : 230 v ac +/ bis tolerance 9. driver efficacy : > 85 % 10. system efficacy : > 110 lm/w 11. lumens output wattage x system efficacy 12. warranty : 3 years 13. optical cover/lens type: polycarbonate high impact resistant & less glare meeting impact protection code ik08 / polycarbonate micro lens optic polycarbonate high impact resistant & less glare meeting impact protection code ik07 / polycarbonate micro lens optic 14. thd <10% 15. housing: high pressure die cast aluminium housing/heat sink which gives rugged feature for industrial application. high pressure die cast aluminium housing ( adc 12 ) 16.mounting device : suitable for diameter up to 52 mm to 58 mm 17. operating temperature: 0 50 deg c 18. rohs (restriction of hazardous substances) compliance rohs compliance 19. ce mark na 20. protection class iec : safety class i 21. led chip efficacy : > 135 lm/w schedule 5 m8225121036 technical specifications : led panel light led based 2x2 recess type fitting : 36w 1. system power/wattage : 36w 2. power factor : >0.95 3. cri ( color rendering index) : >80 4. cct (correlated color temp) : 5700 +/ ansi tolerance* 5. surge protection device : a. internal : 2.5 kv b. external : 10 ka, 20 kv 6. cable : as per manufacturers standard. 7. ip (ingress protection): ip20 8. input voltage : 230 v ac +/ bis tolerance 9. driver efficacy : >85% 10. system efficacy : >100lm/w 11. lumens output: wattage x system efficacy 12. optical cover/lens material : polymathic methacrylate 13. thd : <10% 14. housing: metal, optic material : polystyrene, fixation material steel 15.mounting arrangement: recess 16. operating temperature: 0 45 deg c 17. ce mark na 18. minimum impact protection: ik 02 19. protection class iec : safety class i 20. led chip efficacy : >135 lm/w 21. life test/burning hours : 50000 hrs life with 70% lumens maintained 22. beam angle : luminaire light beam spread 120° schedule 6 m8225123537 led based hand lamp ( flame proof) 15w,24v led based wattage: 15 w cri>70 cct: 5700 to 6500 k. +/ ansi tolerance surge protection device: 4 kv system efficacy: >90 lm/w ingress protection: ip 66 operating voltage: 24 v warranty : 3 years gas group :iib & iic temp class :t5 material construction :lm6 gasket :moulded neoprene enclosure:ex d as per is/iec 60079 i:2007 certification: cimfr (dhanbad),bis & peso/dgms (ccoe) licenses is mandatory. material housing:copper free die cast aluminium alloy,lm 6; cu <0.004% hardware such as nut,bolt/washers: stainless steel transparent part: heat resistant and toughened type a clear dome glass/ flat glass gasket: endless moulded neoprene. operating temperature: 10 to 50 deg c type of painting : high build epoxy / marine coating with stopper plug & double compression cable gland. schedule 7 m8225125180 technical specifications : led well glass non flameproof 70 w 1. system power/wattage : 70w 2. power factor : >0.95 3. cri ( color rendering index) : >75 4. cct (correlated color temp) : 5700 +/ ansi tolerance* 5. surge protection device : a. internal : 4kv b. external : 10 ka, 20 kv 6. life test/burning hours : 50000 hrs life with 70% lumens maintained 7. ip (ingress protection) : ip 66 waterproof, dustproof, impact proof & corrosion proof features meeting requirement of outdoor application. 8. input voltage : 230 v ac +/ bis tolerance 9. driver efficacy : >85 % 10. system efficacy : >100 lm/w 11. lumens output wattage x system efficacy 12. cable : as per manufacturer standard 13. optical cover/lens type: polycarbonate bowl/cover frosted high impact resistant & less glare meeting impact protection code ik08 14.minimum ik test requirement for luminaire ik08 15. thd : <10% 16. housing: high pressure die cast aluminium housing/heat sink which gives rugged feature for industrial application. 17.mounting arrangement: adjustable mounting bracket / c clamp for suspension & the fixture should have tillable adjustment for changing angle. 18. operating temperature: 0 50 deg c 19. rohs (restriction of hazardous substances) compliance rohs compliance 20. ce mark na 21. protection class iec : safety class i 22. led chip efficacy : >135 lm/w 23 life test/burning hours : 50000 hrs life with 70% lumens maintained schedule 8 m8225125241 technical specifications : led well glass flameproof 120 w 1 system power/wattage : 120 w 2 power factor : >0.95 3 cri ( color rendering index) : >75 4 cct (correlated color temp) : 5700 +/ ansi tolerance* 5 surge protection device : 1. internal : 5kv ; 2. external 10 ka, 20 kv 6 life test/burning hours : 50000 hrs life with 70% lumens maintained 7 ip (ingress protection) : ip 66 8 voltage : 230 v ac +/ bis tolerance 9 driver efficacy : >85% 10 system efficacy : >100 lm/w 11 gas group : iia, iib & iic 12 material of construction : lm6 13 gasket : molded silicon 14 enclosure : ex d as per is/iec 60079 i : 2007 15 temperature class : a temperature class (upto 50w lights) : t6 b temperature class (more than 50w lights) : t5 16 certification & approval : cimfr, bis & peso (ccoe) /dgms / ce / rohs 17 materials a housing : copper free die cast aluminium alloy, lm6 ; cu < 0.004% b hardware such as nut, bolts, washers : stainless steel c transparent part : optical cover/lens type: polycarbonate bowl/cover frosted high impact resistant & less glare meeting impact protection code ik08 18 thd : <10% 19 minimum ik test requirement for luminaire ik08 20 operating temperature : 0 50 deg 21 type of painting : high build epoxy / marine coating 22 double compression gland both side : ertl or cimfr certified 23 mounting arrangement: adjustable mounting bracket / c clamp for suspension & the fixture should have tillable adjustment for changing angle. 24 led mounted : smd / cob 25 led chip efficacy : >135 lm/w schedule 9 m8225127405 technical specifications :led based flood light fitting : 70w (minimum) 1. system power/wattage : 70 w +/ bis tolerance 2. power factor : > 0.95 3. cri ( color rendering index) : > 70 4. cct (correlated color temp) : 5700 k +/ +/ ansi tolerance 5. surge protection device : 20 kv / 10ka a. internal >= 4 kv b. external external 10 ka, 20 kv 6. cable :as per manufacturer standard 7. ip (ingress protection) :ip 66 waterproof, dustproof, impact proof & corrosion proof features meeting requirement of outdoor application. ip66 8. input voltage : 230 v ac +/ bis tolerance 9. driver efficacy : > 85 % 10. system efficacy : > 110 lm/w 11. lumens output wattage x system efficacy 12. warranty : 3 years 13. optical cover/lens type: polycarbonate high impact resistant & less glare meeting impact protection code ik08 / polycarbonate micro lens optic polycarbonate high impact resistant & less glare meeting impact protection code ik07 / polycarbonate micro lens optic 14. thd :< 10 % 15. housing: high pressure die cast aluminium housing/heat sink which gives rugged feature for industrial application. high pressure die cast aluminium housing ( adc 12 ) 16.mounting device : angle adjuster 17. operating temperature: 0 50 deg c 18. rohs (restriction of hazardous substances) compliance rohs compliance 19. ce mark na 20. protection class iec : safety class i 21. led chip efficacy : > 135 lm/w schedule 10 m8225127432 technical specifications :led based flood light fitting : 190w (minimum) 1. system power/wattage : 190 w +/ bis tolerance 2. power factor : > 0.95 3. cri ( color rendering index) : > 70 4. cct (correlated color temp) : 5700 k+/ ansi tolerance 5. surge protection device : 20 kv / 10ka a. internal >= 4 kv b. external external 10 ka, 20 kv 6. cable : as per manufacturer standard 7. ip (ingress protection) :ip 66 waterproof, dustproof, impact proof & corrosion proof features meeting requirement of outdoor application. ip66 8. input voltage : 230 v ac +/ bis tolerance 9. driver efficacy : > 85 % 10. system efficacy : > 110 lm/w 11. lumens output wattage x system efficacy 12. warranty : 3 years 13. optical cover/lens type: polycarbonate high impact resistant & less glare meeting impact protection code ik08 / polycarbonate micro lens optic polycarbonate high impact resistant & less glare meeting impact protection code ik07 / polycarbonate micro lens optic 14. thd : < 10 % 15. housing: high pressure die cast aluminium housing/heat sink which gives rugged feature for industrial application. high pressure die cast aluminium housing ( adc 12 ) 16.mounting device : angle adjuster 17. operating temperature: 0 50 deg c 18. rohs (restriction of hazardous substances) compliance rohs compliance 19. ce mark na 20. protection class iec : safety class i 21.led chip efficacy : > 135 lm/w schedule 11 m8225127520 technical specifications :led based flood light fitting :140 w 1. system power/wattage : 140w +/ bis tolerance 2. power factor : > 0.95 3. cri ( color rendering index) : > 70 4. cct (correlated color temp) : 5700 k +/ ansi tolerance 5. surge protection device : 20 kv / 10ka a. internal >= 4 kv b. external external 10 ka, 20 kv 6. cable : as per manufacturer standard 7. ip (ingress protection) :ip 66 waterproof, dustproof, impact proof & corrosion proof features meeting requirement of outdoor application. ip66 8. input voltage : 230 v ac +/ bis tolerance 9. driver efficacy : > 85 % 10. system efficacy : > 110 lm/w 11. lumens output wattage x system efficacy 12. warranty : 3 years 13. optical cover/lens type: polycarbonate high impact resistant & less glare meeting impact protection code ik08 / polycarbonate micro lens optic polycarbonate high impact resistant & less glare meeting impact protection code ik07 / polycarbonate micro lens optic 14. thd : < 10 % 15. housing: high pressure die cast aluminium housing/heat sink which gives rugged feature for industrial application. high pressure die cast aluminium housing ( adc 12 ) 16.mounting device : angle adjuster 17. operating temperature: 0 50 deg c 18. rohs (restriction of hazardous substances) compliance rohs compliance 19. ce mark na 20. protection class iec : safety class i 21. led chip efficacy : > 135 lm/w schedule 12 m8225128648 technical specifications : led down lighter 18 w :18w down light reces(round) 1. system power/wattage: 18w 2. power factor : >0.95 3. cri ( color rendering index) : >75 4. cct (correlated color temp) : 5700 +/ ansi tolerance* 5. surge protection device : >3kv 6. diameter 150mm (cutout size) 7. cable :as per manufacturer standard 8. ip (ingress protection): ip 20 9. input voltage : 230 v ac +/ bis tolerance 10. driver efficacy : >75% 11. system efficacy : >100 lm/w 12. lumens output: wattage x system efficacy 14. thd : <10% 15. housing: aluminum die casting 16. minimum impact protection: ik 02 17. operating temperature: 0 45 deg c 18. ce mark na 19. protection class iec : safety class i 20. led chip efficacy : >135lm/w schedule 13 m8225129030 technical specifications : led high bay light 110w (minimum) 1. system power/wattage : 110 w +/ bis tolerance 2. power factor : >0.95 3. cri ( color rendering index) : >75 4. cct (correlated color temp) : 5700 +/ ansi tolerance* 5. surge protection device : a. internal 4kv b. external 10 ka, 20 kv 6. cable :as per manufacturer standard 7. ip (ingress protection) : ip66 waterproof, dustproof, impact proof & corrosion proof features meeting requirement of outdoor application. 8. input voltage : 230 v ac +/ bis tolerance 9. driver efficacy : >85% 10. system efficacy : >100 lm/w 11. lumens output : wattage x system efficacy 12. optical cover/lens type: polycarbonate bowl/cover frosted high impact resistant & less glare meeting impact protection code ik08 13.minimum ik test requirement for luminaire ik08 14. thd : <10% 15. housing: high pressure die cast aluminium housing/heat sink which gives rugged feature for industrial application. 16. mounting arrangement: adjustable mounting bracket / c clamp for suspension & the fixture should have tillable adjustment for changing angle. 17. operating temperature: 0 50 deg c 18. rohs (restriction of hazardous substances) compliance rohs compliance 19. ce mark na 20. protection class iec : safety class i 21.led chip efficacy : >135 lm/w 22. luminaire light beam spread 120 deg 23. life test/burning hours : 50000 hrs life with 70% lumens maintained schedule 14 m8225700161 post top light 45w led based composite luminaire/decorative light fittings:type of fitting garden/area lighting:fitting particulars post top light 45w led based system power/wattage:45w (minimum) +/ bis tolerance pf:>0.95 cri:>70 cct:5700 to 6500 +/ ansi tolerance ip: ip 65 post top height as per manufacturer drawing. total harmonics distortion :<=10% the luminaire shall be protected against surges and transients of >::=10kv (external), >=4kv (internal) input voltage : 230 v ac +/ bis tolerance lumanaire efficience:>80 for clear glass > 60 for diffused glass driver efficiency:>85% suitable to be retrofitted on up to75 od pipe with 03/04 nuts and bolts. otherwise connector from 75 mm dia to post top led dia to be provided. warranty: 3 years schedule 15 m8225127414 technical specifications :led based flood light fitting : 110 w (minimum) 1. system power/wattage : 110 w +/ bis tolerance 2. power factor : > 0.95 3. cri ( color rendering index) : > 70 4. cct (correlated color temp) : 5700 k +/ ansi tolerance 5. surge protection device : 20 kv / 10ka a. internal >= 4 kv b. external external 10 ka, 20 kv 6. cable : as per manufacturer standard 7. ip (ingress protection) :ip 66 waterproof, dustproof, impact proof & corrosion proof features meeting requirement of outdoor application. ip66 8. input voltage : 230 v ac +/ bis tolerance 9. driver efficacy : > 85 % 10. system efficacy : > 110 lm/w 11. lumens output wattage x system efficacy 12. warranty : 3 years 13. optical cover/lens type: polycarbonate high impact resistant & less glare meeting impact protection code ik08 / polycarbonate micro lens optic polycarbonate high impact resistant & less glare meeting impact protection code ik07 / polycarbonate micro lens optic 14. thd : < 10 % 15. housing: high pressure die cast aluminium housing/heat sink which gives rugged feature for industrial application. high pressure die cast aluminium housing ( adc 12 ) 16.mounting device : angle adjuster 17. operating temperature: 0 50 deg c 18. rohs (restriction of hazardous substances) compliance rohs compliance 19. ce mark na 20. protection class iec : safety class i 21. led chip efficacy : > 135 lm/w schedule 16 m8225125171 technical specifications : led well glass non flameproof 35 w 1. system power/wattage: 35w 2. power factor : >0.95 3. cri ( color rendering index) : >75 4. cct (correlated color temp) : 5700 +/ ansi tolerance* 5. surge protection device : a. internal : 4kv b. external : 10 ka, 20 kv 6. life test/burning hours : 50000 hrs life with 70% lumens maintained 7. ip (ingress protection) : ip 66 waterproof, dustproof, impact proof & corrosion proof features meeting requirement of outdoor application. 8. input voltage : 230 v ac +/ bis tolerance 9. driver efficacy : >85 % 10. system efficacy : >100 lm/w 11. lumens output = wattage x system efficacy 12. cable : as per manufacturer standard 13. optical cover/lens type: polycarbonate bowl/cover frosted high impact resistant & less glare meeting impact protection code ik08 14.minimum ik test requirement for luminaire ik08 15. thd : <10% 16. housing: high pressure die cast aluminium housing/heat sink which gives rugged feature for industrial application. 17.mounting arrangement: adjustable mounting bracket / c clamp for suspension & the fixture should have tillable adjustment for changing angle. 18. operating temperature: 0 50 deg c 19. rohs (restriction of hazardous substances) compliance rohs compliance 20. protection class iec : safety class i 21. led chip efficacy : >135 lm/w 22 life test/burning hours : 50000 hrs life with 70% lumens maintained schedule 17 m8225129137 technical specifications : led high bay light 140 w (minimum) 1. system power/wattage :140w +/ bis tolerance 2. power factor : >0.95 3. cri ( color rendering index) : >75 4. cct (correlated color temp) : 5700 +/ ansi tolerance* 5. surge protection device : a. internal 4kv b. external 10 ka, 20 kv 6. cable : :as per manufacturer standard 7. ip (ingress protection) : ip66 waterproof, dustproof, impact proof & corrosion proof features meeting requirement of outdoor application. 8. input voltage : 230 v ac +/ bis tolerance 9. driver efficacy : >85% 10. system efficacy : >100 lm/w 11. lumens output : wattage x system efficacy 12. optical cover/lens type: polycarbonate bowl/cover frosted high impact resistant & less glare meeting impact protection code ik08 13.minimum ik test requirement for luminaire ik08 14. thd : <10% 15. housing: high pressure die cast aluminium housing/heat sink which gives rugged feature for industrial application. 16. mounting arrangement: adjustable mounting bracket / c clamp for suspension & the fixture should have tillable adjustment for changing angle. 17. operating temperature: 0 50 deg c 18. rohs (restriction of hazardous substances) compliance rohs compliance 19. ce mark na 20. protection class iec : safety class i 21.led chip efficacy : >135 lm/w 22. luminaire light beam spread 120 deg 23. life test/burning hours : 50000 hrs life with 70% lumens maintained schedule 18 m8225129058 technical specifications : led high bay light 190w (minimum) 1. system power/wattage :190w +/ bis tolerance 2. power factor : >0.95 3. cri ( color rendering index) : >75 4. cct (correlated color temp) : 5700 +/ ansi tolerance* 5. surge protection device : a. internal 4kv b. external 10 ka, 20 kv 6. cable : as per manufacturer standard 7. ip (ingress protection) : ip66 waterproof, dustproof, impact proof & corrosion proof features meeting requirement of outdoor application. 8. input voltage : 230 v ac +/ bis tolerance 9. driver efficacy : >85% 10. system efficacy : >100 lm/w 11. lumens output : wattage x system efficacy 12. optical cover/lens type: polycarbonate bowl/cover frosted high impact resistant & less glare meeting impact protection code ik08 13.minimum ik test requirement for luminaire ik08 14. thd : <10% 15. housing: high pressure die cast aluminium housing/heat sink which gives rugged feature for industrial application. 16. mounting arrangement: adjustable mounting bracket / c clamp for suspension & the fixture should have tillable adjustment for changing angle. 17. operating temperature: 0 50 deg c 18. rohs (restriction of hazardous substances) compliance rohs compliance 19. ce mark na 20. protection class iec : safety class i 21. led chip efficacy : >135 lm/w 22. luminaire light beam spread 120 deg 23. life test/burning hours : 50000 hrs life with 70% lumens maintained total quantity : 26250...

East Central Railway - Bihar

45900915 auction sale of bio tank released from coaches direct mounting type & j bracket type, i lot no 37598081855, location near incinerator...

East Central Railway - Bihar

45792683 supply of safety bracket for boxnhl wagonsafety bracket for boxnhl wagon,safety bracket for boxnhl wagon to rdso drg. no. wd 09034 s 13 alt 2, item no. 7. [ war ranty period: 30 months after the date of delivery ] ]...

East Central Railway - Bihar

45788447 supply of rubber kit for sa 9 valve comprising of 5 items. specification : as per sl no. items wabco pt.no. rdso drg.no. qty/set a gasket bracket 560009 skdp 3056 1 b o ring 531868 skdp 3031 5 c diaphragm 526346 skdp 3052 1 d o ring 564056 skdp 3031 1 e o ring 523734 skdp 3031 2rubber kit for sa 9 valve comprising of 5 items. specification : as per sl no. items wabco pt.no. rdso drg.no. qty/set a gasket bracket 560009 skdp 3056 1 b o ring 531868 skdp 3031 5 c diaphragm 526346 skdp 3052 1 d o ring 564056 skdp 3031 1 e o ring 523734 skdp 3031 2,rubber kit for sa 9 valve comprising of 5 items as per annexure. [ warranty period: 3 0 months after the date of delivery ] ] csd/trs/ddu, ecr uttar pradesh 713.00 set...

Purvanchal Vidyut Vitaran Nigam Limited - Bihar

45579884 tender for roof treatment of control room and other miscellaneous civil work at 33/11 kv substation shahganj, sonbhadra, 1 excavation in foundation in ordinary soil (loam clay or sand) including lift upto 1.5m and lead upto 30m and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of the foundation work. (code no. 2.6.1) 2 1:5:10 (1 cement : 5 coarse sand (zone iii) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) excluding the cost of centering and shuttering all work up to plinth level . (code no. 4.1.10) 3 providing and laying in position cement concrete of specified grade 1:2:4 (1 cement : 2 coarse sand (zone iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) excluding the cost of centering and shuttering all work up to plinth level . (code no. 4.1.3) 4 providing and laying 1:1½:3 (1 cement: 1½ coarse sand (zone iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level : (code no. 4.1.2) 5 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). (code no. 5.3) 6 centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers (code no. 5.9.5) 7 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand). (code no. 6.1.2) 8 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : (code no.6.4.1) 9 brick work in foundation & plinth with old dismantledbricks (supplied by department free of cost) and coarse sandmortar in 1:6 including supply of all other materials, labour, removing mortar & cleaning of old & used bricks,t&p etc complete. (csi no. 6.18)(nsi no. 3) 10 steel work welded in built up sections/ framed work, in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. (code no. 10.25.2) 11 thermo mechanically treated bars of grade fe 500d or more. steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. (code no. 5.22a.6) 12 12 mm cement plaster of mix 1:4 (1cement:4coarse sand) (code no. 13.4.1) 13 12 mm cement plaster of mix 1:6 (1cement:6coarse sand)(code no. 13.4.2) 14 providing (12x15) mm section groove in plasterincluding all material, labour andt&p etc. required for proper completion of the work. (csi no. 11.16)(nsi no. 34) 15 champering the edge of concrete in auxiliary structure, of size 25 mm wide in triangular section including all materials, labour & t&p etc complete. (csi no.11.18)(nsi no. 35) 16 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including isi marked stainless steel butt hinges with necessary screws(code no. 9.20.2) 17 6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of lime wash on top of walls when dry for bearing of r.c.c. slabs and beams. (code no. 13.17) 18 providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.(b) laying second layer of fibre glass cloth when the first layer is still green. overlaps of joints of fibre cloth should not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. this will be allowed to air cure for 4 hours followed by water curing for 48 hours. the entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.for the purpose of measurement the entire treated surface will be measured. ( code no. 22.6) 19 cement concrete 40 mm thick with 20 mm nominal size stone aggregate flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. (code no. 11.3.1) 20 providing and laying vitrified floor tiles size of tile 600x600 mm in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. (code no. 11.41.2) 21 deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm.(code no. 11.42) 22 providing and fixing glass strips in 40 mm wide and 4 mm thick joints of terrazo/ cement concrete floors.(code no. 11.13.1) 23 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :one or more coats on old work(code no. 13.99.1) 24 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade old work (two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface (code no. 13.112.1) 25 wall painting with acrylic emulsion paint, having voc (volatile organic compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. (code no. 13.82.2) 26 demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge. (code no. 15.7.4) 27 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge.(code no. 15.3) 28 dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.(code no. 15.25) 29 providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.00 mm thick glass panes(code no. 10.30.1) 30 dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead of area 3 sq. metres and below (code no. 15.12.1) 31 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. (code no. 15.56) 32 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete( code no. 13.88) 33 providing and fixing water closet squatting pan (indian type w.c. pan ) white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. (code no. 17.1.1) 34 providing and fixing wash basin with c.i. brackets, 15 mm dia cp brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required. (a)white vitreous china wash basin size 550x400 mm with a 15 mm cp brass single hole basin mixer (code no. 17.7a) 35 providing and placing on terrace (at all floor levels) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (code no. 18.48) 36 providing and laying swr, pvc 110 mm dia ( finolex or equivalent ) pipe including cost of excavation, c.c etc including its jointing and connection, all materials, labour and t&p etc. required for proper completion of the work. (csi no. 27.29c) nsi sl. no.110 37 providing and fixing chlorinated polyvinyl chloride (cpvc) 15 mm nominal dia pipes pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.. (code no. 18.8.1) 38 providing and fixing chlorinated polyvinyl chloride (cpvc) 20 mm nominal dia pipes pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.. (code no. 18.8.2) 39 providing and fixing chlorinated polyvinyl chloride (cpvc) 25 mm nominal dia pipes pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge.. (code no. 18.8.3) 40 providing and fixing gun metal gate valve with c.i. wheel of approved quality (screwed end) :25 mm nominal bore (code no. 18.17.1) 41 providing and fixing c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931 15mm nominal bore(code no. 18.53.1) 42 providing and fixing 15 mm nominal bore c.p. brass bib cock of approved quality conforming to is:8931 : (code no. 18.49.1) 43 supply & installation of electrical control panel of l&t / havells or equivalent make for submersible pump / pumpset containing contractor relay condenser.(csi no. 19.31a) for 1 hp pump set single phase) (nsi 55) 44 supply & installation ofsubmersible pump of k.s.b/ calama. or eqt. make including cost of labour, t&p and material required for completion of work. (1 hp outlet 32 mm dia. or more, head 78/30,discharge 1100/2800 lph) (csi no. 19.32a)(nsi 56) 45 lowering of m.s. column pipe in tubewell including supply of nuts, and bolts, packing and also carriage of pipe from workshop to site including all labour, t&p etc. required for proper completion of the work.a)80/65/50/40/32 mm dia. (csi no. 19.27)(nsi no. 51) 46 supplying and drawing following 3 x 2.5 sq. mm sizes of frls pvc insulated copper conductor, single core cable in the existing surface/ recessed steel/ pvc conduit as required.(dsr e&m 2022 1.17.12) 47 supply & fixing of steel wire rope forsubmersible pump including cost of labour, t&p and material required for completion of work.(csi no. 19.34)(nsi 57) 48 wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm frls pvc insulated copper conductor single core cable in surface / recessed medium class pvc conduit, with modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc as required..group c (dsr e&m 2022 1.10.3) (code no. 27.01) 49 wiring point for plug with 1.5sq. mm fr pvc insulated multistrand single core copper conductor cable in pvc conduit pipe on surface with 1 sqmm frlsh pvc insulated multistrand copper conductor cable as earthwire drawn inside the conduit,piano type switch and ceiling rose/angle/batten holder on 3mm thick phenolic laminated backelite sheet etc,complete in all respects,as directed, including maching colour wash.(uppwd ele sch 2018 item no 124c) 50 wiring for circuit/ submain wiring with 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required.(dsr e&m 2022 1.14.2) 51 supplying and fixing 5 amps to 32 amps rating,single pole, 240/415 volts, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. (dsr e&m 2022 2.10.1) 52 supply and fixing of power plug with 15amps. 250v. flush type switch and 5pin 15a 250v. flush type universal socket in suitable m.s.box of 175x100x50mm size with phenolic laminated bakelite sheet cover 3mm. thick fixed with brass machinesscrews and cup washer(uppwd ele sch 2018 item no 1139) 53 supplying and fixing 63 amps, double pole, 240 volts, isolator in the existing mcb db complete with connections, testing and commissioning etc. as required.(dsr e&m 2022 2.12.2) 54 supply and fixing of surface /flush mounting 12 ways spn distribution board with additional metal door without mcb complete in all respect as directed by eic(uppwd ele sch 2018 item no 1025 cat a) ...

Eastern Railways - Bihar

45559830 supply of trip pawl brackettrip pawl bracket,trip pawl bracket asm as per drg.no.8074711 alt. cb pur.spec.no.dlw/des/mi sc 333 issue dt. 23.03.2015 rev. nil [pl no. 16050370 ] [ warranty period: 30 months after the date of delivery ] ]...

Eastern Railways - Bihar

45555699 supply of truck brake lever bracket assemblytruck brake lever bracket assembly,truck brake lever bracket assembly as per emd pt.no.40077221 and dlw pt.no. 17 020451 alt c [ warranty period: 30 months after the date of delivery ] ]...

Indian Army - Bihar

45530539 bids are invited for genrel item plywood for general purposes as per is 303 (v2) (q3) , hydraulically regulated door closers (q3) , tower bolts (ferrous metals) as per is 204 (q3) , wood screws (q3) , non ferrous metal butt hinges as per is 205 (q3) , wire nails (q4) , door handles as per is 208 (q4) , hasps and staples as per is 363 (q3) , wire mesh fabric or cloth (v2) as per is 1568 (q3) , stainless steel kitchen plate rack 30 cm into 36 cm into 9 cm , looking mirror 600 into 450 mm , fevicol 1 kg , pvc rawl plug 100 nos pkt , window glass ordinary 3 mm thick 1 point 2m into 1 point 2m , wooden beading of size 20mm into 6mm into 8 inch , wooden beading of size 20mm into 20 inch size 20mm into 6mm into 20 inch , round plug wooden , gi wire binding , bracket for curtain rod , putty 1 kg pkt , aluminum curtain rod 19 mm dia into 12ft lenght , super flush strip 100 mm wide 10 mtr long , pvc float valve 20 mm , gate valve brass 20mm , hack saw blade , gate valve 15 mm , gate valve 25 mm brass , pvc float valve 15mm , pvc float valve 25 mm , pvc stop cock 15mm dia , water storage tank 500 l isi marked , pvc lid for 1000 ltrs capacity , pvc lid for 500 ltrs capacity , m seal 200 gms pkt , brass jumper washer for 15 mm bib tap , hdpe grating 100 mm dia , gi hook for pipeline , gi check nut 20mm , gi check nut 25mm , cp glass self 450 mm long with 4mm glass , ms angle bracket for whb , cement 50 kg , white cement 1 kg , pad lock 6 lever , drill bit for brick hole 4mm 5mm 6mm 8mm and 10mm 1 50 total quantity : 437...

Department Of Science And Technology - Bihar

45514400 supply of machines and laboratory equipments for civil engineering department in the premises of lnjpit chapra 1 automatic mortar mixer, digital, capacity 5 l automatic/manual mortar mixer, 4.75 litre nominal capacity bowl) standard supply includes basic unit with stainless steel mixing bowl and stirrer, program controller with status indicators to run the mixer in fully automatic or manual mixing mode. low speed 140+/ 5 , 62+/ 5, high speed 285+/ 10, 125+/ 10, suitable for operation on 220v, 50hz, single phase, ac supply 2 cement mortar moulds cement mortar moulds, steel for 70.6mm cube with isi certification mark , is 10086, machined with a permissible variation of 0.15mm and finished within tolerance of +0.15mm 0.10mm 3 cube moulds cast iron , for mm cube isi certification is:10086 ,angle between adjacent interior faces and top and bottom plates of mould 90+/ 0.5deg, length of base plate –min.280mm, width of base plate –min.215mm, machined flat to +/ 0.2mm of specified dimensions .approx wt minimum to 14kg 4 digital platform balance electronic balance, capacity min 100kg +/ 10g 5 digital compression testing machine digital compression testing machine capacity min: 2000kn with touch screen display with tft with min. 800 x 480 pixel. real time display of time vs load in kn/mpa. least count min 0.1kn, maximum clearance between platens 370mm, maximum distance between side plates 340mm, platen size min 222 0 dia, piston dia min. 222 2mm piston stroke 50mm, hydraulic system with 15 liters. control system microprocessor based, pace rate control option must be incorporated through lever auto shut down facility should consist of parfex glass fixed safety door on the front and back. calibration & validation machine must be with nccbm/nabl calibration certificated with traceability certificate. digital indicator has provision to configure more than one mode. model compression/mode2 flexure/mode3 prism testing/mode4 tensile splitting strength. communication with software support machine should supplied with followings 1) loading unit consisting of loading frame with jack, dust cover &upper platen. 2) pumping unit 3) e.di touch screen 4) spacer with locating pin 4 nos 5) step pin with ring 1 no 6) flexible hose pipe 1 no 7) hydraulic oil 15 lt. 8) lifting handle for ram 1 no 9) spanner 24 x 27 2nos 10) allen key 3mm 1 no 11) main cable for edi ino 12) control motor cable 1 no 13) eye hook 1 no 14) dust cover 1 no 15) calibration certificate 1 no 16) operating manual 1 no 6 sieves test sieve, 18th dia gi frame size 100,80,63,50,40,31,25,20,12.5,10&4.75,2,1mm & 600,425,300,212,150,75 micron with lid & pan 7 brick mould standard 8 cement tensile testing mould standard 9 autoclave mould standard 10 air permeability apparatus perforated disc & rubber bulb (5 set) 11 concrete mixing tray 2 feet x3 feet and depth 8inch concrete mixing tray 12 steel scale 300mm size 13 electronics balance up to 500g, and 5 kg 14 cement tensile testing machine testing machine: ref. standard en 196 1 loading speed of the double lever system: 50 +/ 10 n/sec, flexure jaw diameter of the loading roller: 10mm supporting roller diameter: min. 10mm baffle plate span: 46mm environmental engineering lab 1 bench top meter for measurement of water quality parameters with all accessories ph, conductivity & dissolved oxygen and ion measurement in water sample (with electrodes of na+, k+, ca., mg., co3—, f , cl , so4—etc) 2 magnetic stirrer with hot plate number of stirring positions. i calibration. automatic calibration type of drive motor motorless magnetic coil type display optio/,output read out option digital magnetic sorrel, with a hot plate or some other means for heating the liquid controller type electronically controlled mid programmable speed control accuracy of set speed (+/ ) (rpm): 0 maximum stirring capacity per position: 2000 milli litre ceramic top plate material, digital front panel, last run memory ce certified product (seller to furnish supporting document to buyer on demand) speed speed mode venable speed minimum speed possible (rpm) 50 maximum speed (rpm) of variable speed mode equipment 1600 dimensions external dimension. (height )200 milli meter external dimension. width 200 milli meter external dimension: depth: 50 milli meter body material stainless steel finish of body material powder coated top plate finish. ceramic coated stir bar star bar cover metro al ptfe quoted alnico magnet stir bar length. 200 milli meter top plate top plate area shape. circular circular top plate diameter 1000 milli meter top plate finish. ceramic coated 3 fluoride ion meter (with fluoride electrode) type / nomenclature/ protection type of meter / analyzer bench type functional nomenclature multi parameter water quality analyzer ingress protection (main unit). ip, 56 calibration. automatic compensation / correction temperature correction. automatic salinity correction automatic display • storage type of display lcd with backlight display digit size 30 milli meter number of digits in display 5 inch number of parameters displayed simultaneously. 3 memory (in data sets): 2000 internal memory (gb) 64 date & time stamp in entries yes connectivity interface. usb, rs 232 power source alkaline battens (non rechargeable), mains (230 +/ 10 volts 150 hz ac) battery size, if non rechargeable battery aa battery chemistry, rf rechargeable battery li ion voltage of each battery 1 5 volt number of batteries required for operation 4 number of batteries inclusive in the scope of supply 4 battery capacity (mah) 800 battery life 800 hour suitable adapter to be supplied to make the equipment work on 230 v ± 10% 50 hz. yes geotechnical engineering lab 1 pycnometer as per is 2386 (pan 3) consist of a i kg glass one with brash cone 2 liquid limit device casagrande grooving tools and gauge block with ac supply compliance with is 2720 (part 5), is 9259 consists of a hard rubber base casagrande grooving tool gauge block 3 shrinkage limit set as per is 2720 (part 0), porcelain evaporating dish, shrinkage bath, glass cup, min. three metal prongs, perspex plain plate spatula. glass cylinder, 25 ml x 0 3 ml. mercury 4 hydrometer apparatus hydrometer, range 0 20, 20 40, 40 60, 60 80, & 80 i00 5 i.s. sieves 20 cm diameter brass aperture size 4,75 mm, 2.36mm, l 18mm, 600micron, 300 micron, i50 micron and 75 micron as per is 460 sieves 20 cm diameter brass aperture size 4.75 mm, 2.36 mm, 1.18mm, 600micron, 300micron,150 micron and 75 micron as per is 460 6 c.b.r. apparatus ref standards is 9669, is 2720 (part xvi), bs 1377, 1924, en 13286 47/ astm d 1883, aashto 193 digital indicator micro controller multi line alpha numeric lcd display for all simultaneously channel load frame, with lvdt 20mm, 50 kn capacity, three speed 1.5, 1.25 & 2.5 mm/min mould mild steel 150mm id x 175 mm h perforated base plate mild steel, for 12001 mould extension collar mild steel, 150 mm id x 50 mm high penetration piston 50 mm face dia adjustable bracket for penetration dial gauge circular metal spacer disc, with detachable handle, 148 mm dia x 47.7 mm high annular metal weight 2.5 kg, 147 mm dia with 53 mm dia central hole slotted metal weight 2.5 kg, 147 mm dia, with 53 mm dia slot perforated plate 148 mm dia, with adjustable stem and lock nut cutting collar rammer 2.6 kg, 310 mm controlled drops rammer 4.9 kg, 450 mm controlled drops 7 infra red moisture metre as per the is 2720 (part 2) the speed of drying (about 30 min), the infrared radiation is controlled by a voltage regulator the instrument is provided with on indicator lamp. the balance scale (drum) is divided in terms of moisture percentage on wet weight basis, which are read directly from it graduations me from 0 to 100% in 0.2% divisions suitable for operation on 220 v. 50 hz„ single phase, ac supply capacity min 5g approx.. sensitivity min 10 mg approx.. range 0 to 100% moisture content on wet weight basis reading accuracy min +/ 0 20% portable error min +/ 0 25% m the lower range up to compared to 25% and+/ 1% for moisture contents oven methods share 50% equipment consisting of infra red lamp thermometer (l shaped) 8 proctor test apparatus for heavy compaction proctor test apparatus for light compaction, mild steel as per the is:2720 (part 7), compaction mould, dia 100 mm, height 127.3 mm, volume 1000 ml, rammer 26 kg 9 laboratory hot air digital laboratory over (18”x18”x18”), hot oven 450mm digital 10 electronic balance up to 500g, and 5 kg 11 sieve shaker sieve shaker, motorized, with built in digital timer, a digital timer adjustable from 0 99 minutes is incorporated as an integral part of the equipment. the sieve shaker can carry up to 8 sieves of 20cm diameter, also supplied with 30cm adaptor it is driven by a 4 hp geared motor, the sieve table is inclined from the vertical axis and the direction of inclination changes progressively in the clockwise direction, in addition to the gyratory motion of the table, there is a tapping motion as well suitable for operation on 220 v, 50 hz, single phase, ac supply 12 non corrodible air tight container or can 100 ml, 200 ml, 500 ml, 1000 ml 13 thermometer 50c – 600c 14 glass measuring cylinder 1000ml 15 stopwatch accuracy 0.001 seconds transportation engineering lab 1 softening point test of bituminous material the ring and bat apparatus consists of following steel balls two numbers each of 9 5 mm diameter and weighing 2 5 + 0 05 gm. brass rings two numbers each having depth of 6.4 mm, the inside diameter at bottom and top is 15 9 nun and 17 5 mm respectively ball guides to guide the movement of steel balls centrally support that can hold rings in pontoon and also allows for suspension of a thermometer the distance between the bottom of the rings and the top surface of the bottom plate of the support is 25 num. thermometer that ran read up to 100t with an accuracy of 0 c bath a heat resistant glass beaker not less than 85 mm in diameter and 120 mm in depth sumer 2 penetration test of bituminous material penetrometer container is a no bottomed cylindrical metallic disc with 55 mm in diameter and 35 mm a depth. if the penetration is of the order of 223 or more deeper dish of 70 mm diameter and 45 mm depth is required. the needle is provided with a shank approximately 3 mm in diameter into which it is immovable fixed 3 specific gravity of bitumen by pycnometer method pycnometer wash bottle balance 4 flash and fire point test flash and fire point apparatus flash point range 1040c and below, repeatability 3.50c 5 viscosity test as per is 1206 (part 1) 1978,following equipment ios required tar viscometer cup .it is made of hard brass tube filled with an external brass collar at the upper end of the cylinder to support the cup .the bottom of cup consists of cup consists of a circular of a phosphor bronze plate screwed into the cylinder and made conical to facilitate drainage of tar after use .it is provided with a perfectly cylindrical of diameter f 10mm and length 5mm .orifice of 4mm diameter valve .it serves to close the orifice of cup water bath it is made of copper sheet ,it is cylindrical shape about of 160 mm in diameter 105mm sieve to receive the cup and to hold it in position sleeve to remove the cup and to hold it in position stirrer curved shield receiver a 10 ml graduate cylinder having an internal diameter of not more than 29mm . it has marking of 25ml and 75ml levels thermometer. two thermometers, one for both and another for cup. the measurement range be should 0 degree c to 44degree c or 37.8 degree c or 76 degree c to 122 degree c depending upon whether the viscosity is expected to be low medium or high a stop watch or other timing device capable of being of being read up to ½ second . 6 bitumen content from bituminous core centrifuge extractor with 3000 gram sample capacity in which the bowl may be revolved at controlled, variable speeds up to 3,600 rpm. the apparatus should have explosion proof features filter ring paper or felt, to fit the rim of the bowl oven thermostatically controlled to 110 t 5 °c (230 t 9 °f) chemicals trichloroethylene technical grade, n propyl bromide. d limonene 7 % of water content test of bitumen dean and stark apparatus. flask it is made up of heat resistant glass and its capacity is 500 ml condenser it is made up of heat resistant glass, receiver, heater gas burner an electric burner may be used, graduated cylinder of 100 ml capacity, solvent petroleum or coal tar naphtha which is free from water 8 pmc (pre mix carpet) seal coated sieve size 22.4mm,11.2mm,13.2mm,5.6mm 9 bitumen mix design (marshall method) sieve (20mm, 16mm, i2.5mm, 10mm, 4 75 tom, 2 36mm) cylindrical mould (height 7 5cm & 10 cm diameter) collar sample extractor compaction pedestal (20x20x45 cm) rammer (4 54 kg, weight, dropped from 45.7 cm) breaking head loading machine (gear system to move upward and downward directors, recalibrated proving ling of 5 tones capacity, loading jack with uniform vertical movement of 5cm/mm) weight machine oven ...

Department Of Science And Technology - Bihar

45514143 procurement of civil lab equipments 1 automatic mortar mixer, digital, capacity 5 l automatic/manual mortar mixer, 4.75 litre nominal capacity bowl) standard supply includes basic unit with stainless steel mixing bowl and stirrer, program controller with status indicators to run the mixer in fully automatic or manual mixing mode. low speed 140+/ 5 , 62+/ 5, high speed 285+/ 10, 125+/ 10, suitable for operation on 220v, 50hz, single phase, ac supply 2 cement mortar moulds cement mortar moulds, steel for 70.6mm cube with isi certification mark , is 10086, machined with a permissible variation of 0.15mm and finished within tolerance of +0.15mm 0.10mm 3 cube moulds cast iron , for mm cube isi certification is:10086 ,angle between adjacent interior faces and top and bottom plates of mould 90+/ 0.5deg, length of base plate –min.280mm, width of base plate –min.215mm, machined flat to +/ 0.2mm of specified dimensions .approx wt minimum to 14kg 4 digital platform balance electronic balance, capacity min 100kg +/ 10g 5 digital compression testing machine digital compression testing machine capacity min: 2000kn with touch screen display with tft with min. 800 x 480 pixel. real time display of time vs load in kn/mpa. least count min 0.1kn, maximum clearance between platens 370mm, maximum distance between side plates 340mm, platen size min 222 0 dia, piston dia min. 222 2mm piston stroke 50mm, hydraulic system with 15 liters. control system microprocessor based, pace rate control option must be incorporated through lever auto shut down facility should consist of parfex glass fixed safety door on the front and back. calibration & validation machine must be with nccbm/nabl calibration certificated with traceability certificate. digital indicator has provision to configure more than one mode. model compression/mode2 flexure/mode3 prism testing/mode4 tensile splitting strength. communication with software support machine should supplied with followings 1) loading unit consisting of loading frame with jack, dust cover &upper platen. 2) pumping unit 3) e.di touch screen 4) spacer with locating pin 4 nos 5) step pin with ring 1 no 6) flexible hose pipe 1 no 7) hydraulic oil 15 lt. 8) lifting handle for ram 1 no 9) spanner 24 x 27 2nos 10) allen key 3mm 1 no 11) main cable for edi ino 12) control motor cable 1 no 13) eye hook 1 no 14) dust cover 1 no 15) calibration certificate 1 no 16) operating manual 1 no 6 sieves test sieve, 18th dia gi frame size 100,80,63,50,40,31,25,20,12.5,10&4.75,2,1mm & 600,425,300,212,150,75 micron with lid & pan 7 brick mould standard 8 cement tensile testing mould standard 9 autoclave mould standard 10 air permeability apparatus perforated disc & rubber bulb (5 set) 11 concrete mixing tray 2 feet x3 feet and depth 8inch concrete mixing tray 12 steel scale 300mm size 13 electronics balance up to 500g, and 5 kg 14 cement tensile testing machine testing machine: ref. standard en 196 1 loading speed of the double lever system: 50 +/ 10 n/sec, flexure jaw diameter of the loading roller: 10mm supporting roller diameter: min. 10mm baffle plate span: 46mm environmental engineering lab 1 bench top meter for measurement of water quality parameters with all accessories ph, conductivity & dissolved oxygen and ion measurement in water sample (with electrodes of na+, k+, ca., mg., co3—, f , cl , so4—etc) 2 magnetic stirrer with hot plate number of stirring positions. i calibration. automatic calibration type of drive motor motorless magnetic coil type display optio/,output read out option digital magnetic sorrel, with a hot plate or some other means for heating the liquid controller type electronically controlled mid programmable speed control accuracy of set speed (+/ ) (rpm): 0 maximum stirring capacity per position: 2000 milli litre ceramic top plate material, digital front panel, last run memory ce certified product (seller to furnish supporting document to buyer on demand) speed speed mode venable speed minimum speed possible (rpm) 50 maximum speed (rpm) of variable speed mode equipment 1600 dimensions external dimension. (height )200 milli meter external dimension. width 200 milli meter external dimension: depth: 50 milli meter body material stainless steel finish of body material powder coated top plate finish. ceramic coated stir bar star bar cover metro al ptfe quoted alnico magnet stir bar length. 200 milli meter top plate top plate area shape. circular circular top plate diameter 1000 milli meter top plate finish. ceramic coated 3 fluoride ion meter (with fluoride electrode) type / nomenclature/ protection type of meter / analyzer bench type functional nomenclature multi parameter water quality analyzer ingress protection (main unit). ip, 56 calibration. automatic compensation / correction temperature correction. automatic salinity correction automatic display • storage type of display lcd with backlight display digit size 30 milli meter number of digits in display 5 inch number of parameters displayed simultaneously. 3 memory (in data sets): 2000 internal memory (gb) 64 date & time stamp in entries yes connectivity interface. usb, rs 232 power source alkaline battens (non rechargeable), mains (230 +/ 10 volts 150 hz ac) battery size, if non rechargeable battery aa battery chemistry, rf rechargeable battery li ion voltage of each battery 1 5 volt number of batteries required for operation 4 number of batteries inclusive in the scope of supply 4 battery capacity (mah) 800 battery life 800 hour suitable adapter to be supplied to make the equipment work on 230 v ± 10% 50 hz. yes geotechnical engineering lab 1 pycnometer as per is 2386 (pan 3) consist of a i kg glass one with brash cone 2 liquid limit device casagrande grooving tools and gauge block with ac supply compliance with is 2720 (part 5), is 9259 consists of a hard rubber base casagrande grooving tool gauge block 3 shrinkage limit set as per is 2720 (part 0), porcelain evaporating dish, shrinkage bath, glass cup, min. three metal prongs, perspex plain plate spatula. glass cylinder, 25 ml x 0 3 ml. mercury 4 hydrometer apparatus hydrometer, range 0 20, 20 40, 40 60, 60 80, & 80 i00 5 i.s. sieves 20 cm diameter brass aperture size 4,75 mm, 2.36mm, l 18mm, 600micron, 300 micron, i50 micron and 75 micron as per is 460 sieves 20 cm diameter brass aperture size 4.75 mm, 2.36 mm, 1.18mm, 600micron, 300micron,150 micron and 75 micron as per is 460 6 c.b.r. apparatus ref standards is 9669, is 2720 (part xvi), bs 1377, 1924, en 13286 47/ astm d 1883, aashto 193 digital indicator micro controller multi line alpha numeric lcd display for all simultaneously channel load frame, with lvdt 20mm, 50 kn capacity, three speed 1.5, 1.25 & 2.5 mm/min mould mild steel 150mm id x 175 mm h perforated base plate mild steel, for 12001 mould extension collar mild steel, 150 mm id x 50 mm high penetration piston 50 mm face dia adjustable bracket for penetration dial gauge circular metal spacer disc, with detachable handle, 148 mm dia x 47.7 mm high annular metal weight 2.5 kg, 147 mm dia with 53 mm dia central hole slotted metal weight 2.5 kg, 147 mm dia, with 53 mm dia slot perforated plate 148 mm dia, with adjustable stem and lock nut cutting collar rammer 2.6 kg, 310 mm controlled drops rammer 4.9 kg, 450 mm controlled drops 7 infra red moisture metre as per the is 2720 (part 2) the speed of drying (about 30 min), the infrared radiation is controlled by a voltage regulator the instrument is provided with on indicator lamp. the balance scale (drum) is divided in terms of moisture percentage on wet weight basis, which are read directly from it graduations me from 0 to 100% in 0.2% divisions suitable for operation on 220 v. 50 hz„ single phase, ac supply capacity min 5g approx.. sensitivity min 10 mg approx.. range 0 to 100% moisture content on wet weight basis reading accuracy min +/ 0 20% portable error min +/ 0 25% m the lower range up to compared to 25% and+/ 1% for moisture contents oven methods share 50% equipment consisting of infra red lamp thermometer (l shaped) 8 proctor test apparatus for heavy compaction proctor test apparatus for light compaction, mild steel as per the is:2720 (part 7), compaction mould, dia 100 mm, height 127.3 mm, volume 1000 ml, rammer 26 kg 9 laboratory hot air digital laboratory over (18”x18”x18”), hot oven 450mm digital 10 electronic balance up to 500g, and 5 kg 11 sieve shaker sieve shaker, motorized, with built in digital timer, a digital timer adjustable from 0 99 minutes is incorporated as an integral part of the equipment. the sieve shaker can carry up to 8 sieves of 20cm diameter, also supplied with 30cm adaptor it is driven by a 4 hp geared motor, the sieve table is inclined from the vertical axis and the direction of inclination changes progressively in the clockwise direction, in addition to the gyratory motion of the table, there is a tapping motion as well suitable for operation on 220 v, 50 hz, single phase, ac supply 12 non corrodible air tight container or can 100 ml, 200 ml, 500 ml, 1000 ml 13 thermometer 50c – 600c 14 glass measuring cylinder 1000ml 15 stopwatch accuracy 0.001 seconds transportation engineering lab 1 softening point test of bituminous material the ring and bat apparatus consists of following steel balls two numbers each of 9 5 mm diameter and weighing 2 5 + 0 05 gm. brass rings two numbers each having depth of 6.4 mm, the inside diameter at bottom and top is 15 9 nun and 17 5 mm respectively ball guides to guide the movement of steel balls centrally support that can hold rings in pontoon and also allows for suspension of a thermometer the distance between the bottom of the rings and the top surface of the bottom plate of the support is 25 num. thermometer that ran read up to 100t with an accuracy of 0 c bath a heat resistant glass beaker not less than 85 mm in diameter and 120 mm in depth sumer 2 penetration test of bituminous material penetrometer container is a no bottomed cylindrical metallic disc with 55 mm in diameter and 35 mm a depth. if the penetration is of the order of 223 or more deeper dish of 70 mm diameter and 45 mm depth is required. the needle is provided with a shank approximately 3 mm in diameter into which it is immovable fixed 3 specific gravity of bitumen by pycnometer method pycnometer wash bottle balance 4 flash and fire point test flash and fire point apparatus flash point range 1040c and below, repeatability 3.50c 5 viscosity test as per is 1206 (part 1) 1978,following equipment ios required tar viscometer cup .it is made of hard brass tube filled with an external brass collar at the upper end of the cylinder to support the cup .the bottom of cup consists of cup consists of a circular of a phosphor bronze plate screwed into the cylinder and made conical to facilitate drainage of tar after use .it is provided with a perfectly cylindrical of diameter f 10mm and length 5mm .orifice of 4mm diameter valve .it serves to close the orifice of cup water bath it is made of copper sheet ,it is cylindrical shape about of 160 mm in diameter 105mm sieve to receive the cup and to hold it in position sleeve to remove the cup and to hold it in position stirrer curved shield receiver a 10 ml graduate cylinder having an internal diameter of not more than 29mm . it has marking of 25ml and 75ml levels thermometer. two thermometers, one for both and another for cup. the measurement range be should 0 degree c to 44degree c or 37.8 degree c or 76 degree c to 122 degree c depending upon whether the viscosity is expected to be low medium or high a stop watch or other timing device capable of being of being read up to ½ second . 6 bitumen content from bituminous core centrifuge extractor with 3000 gram sample capacity in which the bowl may be revolved at controlled, variable speeds up to 3,600 rpm. the apparatus should have explosion proof features filter ring paper or felt, to fit the rim of the bowl oven thermostatically controlled to 110 t 5 °c (230 t 9 °f) chemicals trichloroethylene technical grade, n propyl bromide. d limonene 7 % of water content test of bitumen dean and stark apparatus. flask it is made up of heat resistant glass and its capacity is 500 ml condenser it is made up of heat resistant glass, receiver, heater gas burner an electric burner may be used, graduated cylinder of 100 ml capacity, solvent petroleum or coal tar naphtha which is free from water 8 pmc (pre mix carpet) seal coated sieve size 22.4mm,11.2mm,13.2mm,5.6mm 9 bitumen mix design (marshall method) sieve (20mm, 16mm, i2.5mm, 10mm, 4 75 tom, 2 36mm) cylindrical mould (height 7 5cm & 10 cm diameter) collar sample extractor compaction pedestal (20x20x45 cm) rammer (4 54 kg, weight, dropped from 45.7 cm) breaking head loading machine (gear system to move upward and downward directors, recalibrated proving ling of 5 tones capacity, loading jack with uniform vertical movement of 5cm/mm) weight machine oven ...

Indian Army - Bihar

45509861 bids are invited for cp bib cock long body with flange 15 mm fancy type isi marked cp bib cock long nose with flange 15 mm fancy type long body isi marked cp stop cock 15mm male thread isi marked cp brass concealed stop cock 15 mm with flange isi marked cp stop cock 15mm female thread isi marked cp angle cock 15 mm with flange isi marked cp angle cock two way 15mm with flange as per is 8931 abs hand shower multi flow 100 x 230mm with 1.5 mtr ss tube and abs hook abs overhead shower 125mm dia cp brass health faucet with ss pipe 1.0 mtr and abs hook cp jet spray cp wall mixer with l bend for overhead shower 15mm isi marked cp wall mixer telephonic with crutch with provn for hand shower 15mm isi marked central hole cp basin mixer without pop up cp pillar cock swan neck t or m 15 mm fancy type isi marked wall mounted cp sink mixer with regular spout 15 mm brass cp towel rail glossy finish round 600 mm long pvc ball cocks high pressure with epoxy coated alumn rod with hd ball 20 mm complete pvc ball cocks high pressure with epoxy coated alumn rod with hd ball 25 mm complete looking mirror 600 x 450 x6 mm with frame glass shelves 500 x 60 mm ply wood 6ft x 3ft x 12 mm bwr gde as per is 303 pvc flushing cistern low level of 10 ltr capacity isi marked collapsible pvc waste pipe 32mm for whb basin 950mm long brass cp soap dish fancy type glossy finish collapsible pvc waste pipe 40mm for urinal 800mm long cp ss waste coupling light half threaded 32 mm dia brass cp waste coupling heavy full threaded 40 mm dia brass cp waste coupling heavy full threaded 50 mm dia cp waste coupling 100 mm dia for stainless steel sink plastic seat cover for ewc colour white plate rack stainless steel grade 204 of size 786mm height 914mm width 254mm depth and 0.85mm ss grating round slotted doom type 102 mm dia aisi 304 ss grating round slotted doom type 102 mm dia aisi 304 with waste hole plate rack stainless steel grade 204 of size 786mm height 760mm width 254mm depth and 0.85mm pvc brauded connection 15 x 300mm long with ptmt nut collar bush and spanner pvc brauded connection 15 x 375mm long with ptmt nut collar bush and spanner pvc brauded connection 15 x 450mm long with ptmt nut collar bush and spanner pvc brauded connection 15 x 600mm long with ptmt nut collar bush and spanner white portland cement a grade 1.0 kg decorative quality multi purpose ss bracket foldable multipurpose for ss sink brass sliding bolt 300 mm with 16mm bolt complete brass sliding bolt 250 mm with 16mm bolt complete wire mesh 0.47 mm aperture of width 1200 mm length 8.20mtr aluminum door handle d type 100 mm isi marked aluminum door handle d type 125 mm isi marked aluminum door handle d type 150 mm isi marked aluminium alloy extruded section curtain rails of size 25mm and 12ft long as per is 10342 1982 curtain rod aluminum 20mm aluminium single diamond brackets curtain holder with ss support 1 inch curtains rod pocket finials designer pack of 1 pair cp hydraulic door closer cast iron body designation no 2 universal type suitable for door shutters of 701 to 850mm in width and weight between 36 to 60 kg ms butt hinges medium grade 100 mm as per is 1341 1992 aluminium barrel tower bolts with barrel and bolt of almn extruded section of 150mm length aluminium skeleton tower bolts with plate staples and bolt of extruded sections of aluminium alloy of size 150mm ms sliding door 250mm with bolt type and complying to is 281 1991 ms sliding door 200mm with bolt type and complying to is 281 1991 ms sliding door 300mm with bolt type and complying to is 281 1991 sliding door bolt aluminum 300mm with fixing bolts complete complying to is 281 1991 floor door stopper brass 125mm confirming to is 1823 1980 bracket cp for curtain rod 19 mm floor door stopper aluminum of 125mm confirming to is 1823 1980 aluminum tower bolt 200mm confirming to is 204 part 2 1992 aluminum tower bolt 100mm confirming to is 204 part 2 1992 ms bow handle stove enamelled black 125mm conform to is 208 1996 curtain rod stainless steel with brackets 20mm hack saw blade double edge 300 mm hasp and staple aluminum alloy safety type 100 mm conform to is 363 1993 hasp and staple aluminum alloy safety type 50 mm conform to is 363 1994 oil putty for fixing of window glass nails wire polished round 25mm size nails wire polished round 35mm size nails wire polished round 50mm size nails wire polished round 80mm size teak wood beading 4 mm thick x 20 mm half round mild steel 45 x 5 mm standard wood screws drum polish pkt of 200 pieces mild steel 45 x 5 mm standard wood screws drum polish pkt of 200 pieces mild steel 75 x 7 mm standard wood screws drum polish pkt of 200 pieces heavy duty padlocks dark grey with 8 keys 100mm hardened solid steel monoblock lock anti drill and anti saw and weighing not less than 850g gi steel tubing medium gde of 15 mm dia with one socket gi steel tubing medium gde of 20 mm dia with one socket gi steel tubing medium gde of 25 mm dia with one socket gi nipple 15 x 100mm gi nipple 15 x 300 mm gi nipple 15x75mm isi marked gi nipple threaded 15 x 25mm isi marked gi barrel nipple 20x80 mmthreaded isi marked gi bend 90 degree 15 mm dia isi marked cp brass tee 90 degree of 15mm m seal phataphat small packet of 25 gram gi union socket 15 mm isi marked gi union socket 20 mm isi marked gi socket fully threaded 15 mm isi marked gi socket fully threaded 25 mm isi marked gi socket fully threaded 32 mm isi marked gi socket 50 mm gi bend semicircle 15x100 mm isi marked gi bend semicircle 20x100 mm isi marked gi socket reducer 20 x 15 mm gi socket reducer 25x15 mm gi socket reducer 25 x 20 mm gi elbow reducer 32x20 mm isi marked gi tee equal 15mm isi marked gi reducer elbow of size 20 x 15 mm isi marked gi bend metal threaded 90 degree 80 mm dia nut and bolt with washer 6mm dia 50mm long gi tee reducer 50x15 mm x 50 mm isi marked gi socket reducer 50 x 20 mm isi marked gi nipple 20mm galvanized iron pipe nipple gi threaded round union socket polished 50 mm dia gi union socket 3mm thick of 25mm isi marked gi union socket 3mm thick of 15mm isi marked gi tee 3mm thick of 25mm isi marked pvc angle l type polished beading of size 2x10mm x 8ft long pvc angle l type polished beading of size 3x8mm x 8ft long back for chair cb steel without arms back for chair cb steel with arms plain white viscose fabric of width 48 inches for clothing ms screw wood 30 mm mild steel 30 x 7 mm standard wood screws drum polish pkt of 100 pieces ms wood screws powder coated of size 20x 5mm pkt of 200 pieces crome polish wood screw of size 35x8mm pkt of 100 pieces min nails wire polished round 40mm size nails wire polished 3mm round 75mm size synthetic enamel paint briliant white glossy finish in 4 ltr pack container cloth acrylic linen basics homes velvet solid dyed fabric decorative soft smooth silky cloth for sofa 100 x 140 cm beige 1 mtr white square padlock alloy steel with 4 keys 6 levers door lock hacksaw resistant electroplated hardened steel 50mm pack of 1 cylinder housing brass lock 25mm dia bright nickel finish for wardrobe with 2 keys made of brass with 1 yr warranty sliding door lock with key for wardrobe 32 mm nickle silver finish pack of 1 painting brush synth hair flat mini size 12mm paint brush with acrylic nylon blend round bristles of size 25mm pack of 6 paint brush with acrylic nylon blend round bristles of size 50mm pack of 4 super sturdy bristles premium brushes and wooden handle easy clean long lasting painting brush set of 6 black total quantity : 3661...

Indian Oil Corporation Limited - Bihar

45385927 procurement of ksb pump spares , list of item(s) / work(s) as per tender documents , wear ring,case,pmp,p/n 502.01,ksb , wear ring,imp,pmp,p/n 503.01,ksb , pressure ring p/n 454.01 , pressure ring, p/n 454.01 , shft,pmp,p/n 210 , slev,brg,pmp,p/n 529.06 , slev,interstg spacer,pmp,p/n 525.01 , ring,labyrinth,i.b.,pmp,p/n 423.02 , wear ring,case,pmp,p/n 502.01 , ring,split,pmp,p/n 501.11 , ring,split,pmp,p/n 501.12 , bush,throttle,pmp,p/n 542.06 , bush,neck,i.b.,pmp,p/n 456.02 , bush,neck,o.b.,pmp,p/n 456.01 , deflector,pmp,p/n 507.12 , stuffing box housing, p.no. 451.01 , stuffing box housing, p.no. 451.02 , cover, p.no. 160 , spacer slv,chtc 4/5,p/n 525.01 , spacer rng,chtc 4/5,p/n 504.01 , spacer rng,chtc 4/5,p/n 504.02 , spacer ring,chtc 4/5,p/n 504.03 , neck bush ,p/n: 456,chtcr 4/5,ksb , shaftp/n 210 , imp ring,rphb ecm 80 360/2,p/n 503.01 , imp.ring, rphb ecm 80 360/2,p/n 503.02 , shaft sleeve, rphb ecm 80 360/2,p/n 523. , barng sleeve, rphb ecm 80 360/2,p/n 529. , spcer sleve, rphb ecm 80 360/2,p/n 525.0 , labyrinth ring p/n 423.01 , labyrinth ring p/n 423.02 , wearing rings p/n 502.01 , wearing rings p/n 502.02 , spacer ring p/n 504 , spacer ring p/n 504.11 , split ring p/n 501 , gasket p/n 411.25 , gaskets p/n 400.01 , gskt,casing,pn 411.10,rphb hm 80 360/2 , gasket & o ring p/n 400 , throttle bush p/n 542.06 , neck bush(nde),rph ecm 80 360/2,p/n 456. , spacer sleeve p/n 525.04 , neck bush de p/n 456.02 , bearing bracket,p/n 330 , spacer sleeve pn 525.04, a276type410h , imp.wrg.ring(back)p.no 503.02 , impeller wear ring,p/n 503.01 , spacer ring pn 504.11, a276type410h&t , segmental ring, p/n 1501 , split ring pn 501,a276type316 , throat bush(de) pn 456.02,a276type410a , bearing guard(de)p.no. 423.01 , bearing guard(nde) p.no. 423.02 , bearing guard(de)p.no. 423.03 , impeller (stage),p/n:230 , bearing sleeve(pump shaft),p/n:529.01 , bearing sleeve(suc. diff.),p/n:529.02 , bering sleeve(drive sahft),p/n:529.04 , bering sleeve(inter. sahft),p/n:529.03 , stage sleeve,p/n:521 , wearing ring stage,p/n:502.02 , wearing ring suc,p/n:502.01 , split ring,p/n:501 , impellar ring stage,p/n:503.02 , impellar ring suc,p/n:503.01 , bearing bush(disc. casing),p/n:545.01 , bearing bush(suc. diff.),p/n:545.02 , bering bush(adapter),p/n:545.04 , bering bush(bering spider),p/n:545.03 , suction impeller,p/n:231 , o ring (1st stage),p/n:412.01 , o ring (adapter),p/n:412.03 , o ring (s.box),p/n:412.04 , o ring (stage),p/n:412.02...

Military Engineer Services - Bihar

45317672 tender for special repair to buildings no p 73 (urc bldg) at ota gaya; 1 excavating in trenches, n exc 1.5m wide & n exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan & getting out in hard/dense soil 2 excavating in trenches, n exc 1.5m wide & exc 1.5m but n exc 3.0m in depth; for fdn etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan & getting out in hard/dense soil 3 removing excavated soil n exc. 50m & depositing where directed at a level n exc. 1.5 m above the starting point 4 returning, filling in, incl spreading, levelling, watering & well ramming in layers n. exc 25 cm in soil. 5 m & l pcc in foundations, filling and mass concrete type d2 (1:4:8) using 40 mm graded stone aggregate 6 dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete. 7 demolition of concrete of any description and in any position not otherwise specifically provided for complete. 8 demolition ofreinforced cement concrete of any description and in any position not otherwise specifically provided for complete. 9 demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. 10 m & l brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cm 1:4 11 m & l for brickwork with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in cm (1:4) 12 m & l rcc m 25 design mix using 20 mm graded aggregate in beams, cantilevers, lintels over 1.5 m span 13 m & l rcc m 25 design mix using 20 mm graded aggregate in foundations, incl rafts, footings, foundation beams; plinth beams; bases for columns and mass concrete 14 m & l rcc m 25 design mix using 20 mm graded aggregate in columns, pillars, piers, posts and struts 15 m&l rcc m 25 design mix using 20 mm graded aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like 16 form work to sides of concrete foundations, footings, bases of columns,sides & soffits of foundation & plinth beams and similar work rough finished surfaces of concrete flat 17 form work to sides of pillars, posts, struts, piers,columns, and stanchions rough finished surfaces of concrete square, rectangular or polygonal 18 formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (horizontal or sloping) rough finished surfaces of concrete flat 19 m&l mild steel tmt bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality 20 ditto all as per item no 19 above but 6 to 8 mm dia as in spacers and binder 21 s & f of 4 mm thick hpsc (high pressure steam cured) pre primed textured designer board, water resistant, be placed in the grid system duly suspended with 2 mm dia gi bar hangers fixed with steel dash through fasteners from purlins of the roof complete all as specified. 22 m & l for anodised aluminium snap grid frame work for false ceiling all as specified and as directed. 23 m & l for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigments including 15mm thick sceed bed in cm 1:6 complete. 24 s & f of framed work as in including moulding, cuttings, and made to shape as directed, such as grills, gratings, etc with ends of bars shouldered and/or riveted or welded, or forged into spikes, framed guard bars and similar work conforming to fe.290. gde e 165 complete all as directed & specified. 25 m&l rendering 15mm thick in two coat on stone masonry surfaces or surface other than fair face of brickwork in cm (1:4) finished even & smooth (without using extra cement) and applying wpc on second coat @ 3% by wight of cement or manufacturere instruction 26 m&l rendering 10mm thick on stone masonry surfaces or surface fair face of brickwork in cm (1:6) finished even & smooth (without using extra cement) 27 m & l for hard core of broken bricks gauge n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface 28 m & l 75 mm thick pcc type c 2, (1:3:6) using 40mm graded stone aggregate as inpath and concrete surface finished even and smooth without using extra cement. 29 m & l 25mm thick pcc type b 1, (1:2:4) using 20mm graded stone aggregate as in levelling course for tiles complete. 30 m & l for virified ceramic light shade double charged tiles 7.5 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and incl 15mm thick screed bed or bedding layer with cm 1:4 complete. 31 m & l for virified ceramic light shade double charged tiles 7.5 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skitting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and incl 10mm thickrendering bed or bedding layer with cm 1:4 complete. 32 m&l rendering 10mm thick on fair faces of brick work or concrete surfaces in cm (1:3) in ceiling complete. 33 m & l for two coats of exterior weather proof paint white or tinted on walls, fascia of roof or chajjas, col facia at any height on old painted surfaces of brick, stone, concrete, asbestos cement or plastered or unplastered surfaces of bldg all as specified & directed.make : asian paints(apex dust proof) or equivalent paint. 34 m & l for preparation of new plastered surfaces and applying two coat of oil bound distemper over a coat of primer including 1mm thick putty complete all as specified and directed by engr in charge. 35 m & l for preparation of old plastered surfaces and applying two coat of oil bound distemper over a coat of primer including 1mm thick putty complete all as specified and directed by engr in charge. 36 m & l 75mm thick pcc type c 1, (1:3:6) using 40mm graded stone aggregate finished even & smooth without using extra cement as in plinth protection/path 37 taking down chowkhats or frames exceeding 1.50 sqm and not exceeding 4 sqm each but with shutters (without taking off shutters from the frame) complete all as specified. 38 s & f ofpressed steel frames 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed 39 s & f 30 mm flush shuteers solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. 40 s & f framed work as in doors or gates of angle or other section with gusset plates, rails,braces,etc.,complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing completeconforming to fe.290.gde e 165 41 material & labour for providing and fixing stainless steel (grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement. 42 m&l two coat of synthetic enamel paint overnew woodensurfaces of any description not otherwise described over 10cm in width or grith over one coat of pink primerincluding preparation of surfaces complete. 43 m&l two coat of synthetic enamel paint overold woodensurfaces of any description not otherwise described over 10cm in width or grith over one coat of pink primerincluding preparation of surfaces complete. 44 m&l two coat of syntetic enamel paint overnewsteel surface of any description over 10cm in width or grithnot otherwise describedover one coat red oxide primerincluding preparation of surfaces complete. 45 s & f for powder coated aluminium frame for doors,windows, ventilators with one or morerebates including joining cleat for fixing etc. complete all as specified and directed. 46 s & f aluminium handle cast type anodized 150mm size 47 s & f aluminium, anodized, barrel tower bolts of extruded section 200mm long 48 s&f butt hinge extruded aluminum alloy with galvanized ms hinge pin anodised and fixed 125mm long, type b 21 complete. 49 s & f aluminum alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy size 300mm long. 50 m&l for pcc 1:2:4, type b 1 using 20 mm graded stone aggregate as in coping, benching, bed block, lintel band, plinth courses, drains and channels etc including necessary form work complete 51 taking down existing old extg unserviceable lt ug/ service cable of any description and sizecomplete all as specified and directed. 52 supply and laying & testing and commisioning lt underground cable 1100 volts grade, xlpeinsulated and pvc sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ ducts, on poles etc of sizecomplete all as specified and directed 53 (a) 3.5 core x 120 sqmm 54 (b) 3.5 core x 35 sqmm 55 removing of surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed. 56 burnt bricks sub class b laid flat dry across the cable for cable protection all as specified and directed. 57 sand cushioning to ug cable 8cm thick before laying the cable and 15cm above the cable, stretching and testing of cable complete all as specified and directed. note: (i) consolidated / punned sand shall be considered for purpose of payment (ii) sand shall be same as specified for plastering work. 58 s & f outdoor type lt feeder piller box of size 600x600x300mm deep, 415 volts, 3 phase, 4 wire 50 hz having 04 nos colour coded aluminium bus bar of capacity 600 amps mounted on porcelain/ hygroscopic insulators with suitable number of holes for making connections of cables, made out of 3.15mm thick sheet steel crca and mounted on frame of suitable size made out of angle iron 50x50x6mm with 4 nos legs embedded in pcc foundation 300mm below ground level and 300mm above ground level, duly painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, dust and vermin proof, front door with locking arrangement and two earth points by side of the box, cubical type with cable glands, sockets etc and with provision of cable entry from bottom, including painting steel frame complete all as specified. 59 m & l for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to gi earth strip 25x4mm by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, pcc chamber, ci frame and cover, ms funnel with wire mesh all as shown in electrical plate no 3 of ssr part i including excavation and earthwork in any type ofsoil/strata and testing on completion. note: gi earth strip 25x4 mm and 40 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted. 60 taking down copper/aluminium point wiring (light, fan, bell, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendent, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site. 61 taking down ceiling fan/ exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan bladesand deposit to mes store yard of age e/m gaya complete all as specified and directed. 62 m&l for point wiring with 1.5 sq mm single core pvc insulated unsheathed copper frls multi stranded conductor cable in and including concealed pvc conduit of size 20/25mm isi marked inclusive oftees, bend, elbows etc upto and including sunk in anodized pressed steel box for housing switch socket etc withwhite laminated 3 mm thick hylum sheet cover isi marked of suitable size complete including pvc insulated multi stranded copper conductor 1.5sq mm frls cable as earth wire to common earth dolly for connection to ceiling rose to earth terminalincluding cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by engr in charge for following : 63 (a) one light point controlled by one, one way switch 5 amps 64 (b) one fan point/ exhaust fan point controlled by one, one way switch 5 amps. 65 (c) one 3 point 5 amps switch socket outlet point controlled by one switch on the same board. 66 (d) one 3 pin 5 amps switch socket outlet point controlled by one switch on independent board. 67 description all as per item no.3 here in before but using 2.5 sqmm single core copper conductor cable of multistranded flame retardant pvc insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor flame retardant pvc wire as earth continuity conductor along with wiring and connecting to the common earth dolly. 68 description all as per item no.3 here in before but using 4.0 sqmm single core copper conductor frlsh cable of multistranded pvc insulated unsheathed 1100 volts grade for 5/15 amps switch socket combination point including necessary running of4.0 sqmm frlsh pvc insulated copper conductor cable as earth continuity conductor along with wiring and connecting to the common eath dolly. (for ac point) 69 s&f switch piano type single pole 5 amp, 230 volts complete all as specified and directed. 70 s&f switch piano type single pole 15 amp, 230 volts complete all as specified and directed. 71 s&f socket outlet 2 in 1, 3 pin, 5 amp, 230 volts complete all as specified and directed. 72 s&f socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type, 230 volts complete all as specified. 73 s&f ceiling rose, surface bakelite with 3 terminals, isimarked for batten fitting complete all as specified 74 s&f stepped type electronic fan regulator flush type complete all as specified and directed. 75 s&f lamp holder, pvc / polycarbonate type with back plate suitable for batten/ slanting fittings complete all as specified and directed. 76 s&f metal clad box suitable for 230 volt 50 hz ac supplywith 16 amp socket, mcb sp 20/32 amps and 16 amp plug top including removal of old unserviceable one complete all as specified and as directed. 77 m & l for sub main wiring with approved colour coding as per is with two single core pvc insulated frls cable with stranded copper conductor of size 6 sq mm nominal area and drawing into suitable size of pvc non metallic rigid heavy duty pvc conduit of white/ ivory colour and its accessaries isi marked heavy duty of suitable size including concealed in wall etcone run of pvc insulated with 6.0 sqmm (nominal area) stranded copper conductor frls cable as earth wire complete all as specified and as directed. note: two runs of 6 sqmm cable, one run of 6 sqmm cable and one run of pvc conduit will be measured as one unit 78 m & l for sheet metal enclosure mccb dbs, triple pole & neutral 4 way with 200 amp rated bus bar double door suitable for 01 no incoming mccb of 125 amp capacity and 12 nosout going mcb sp complete all as specified and directed. note: mccb & mcbs are measured and paid in separate items. 79 s & f sheet metal enclosure mcb db spn 8 way with 200 amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the dbs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed. 80 s & f for mcb single pole and neutral rated capacity 32 amps, 240 volts breaking capacity 10 ka, c curve complete all as specified and as directed. 81 s & ffor mcb single pole rated capacity 6 to 32 amps, 240 volts breaking capacity 10 ka, c curve complete all as specified and as directed. 82 s & f mccb 4 pole, 125 amps with breaking capacity 16 ka, 415 volts complete all as specified and directed. 83 s & f ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 v, 1200 mm sweep, min air delivery 210 cfm with service value 6.00 bee five star rated with brushless direct current motor (bldc) including electrical connections from ceiling rose to fan terminal complete all as specified and directed. 84 labour hanging only ceiling fan obtained from item no. 2 above and connecting up including provision of 3 core pvc insulated pvc sheathed multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal and m & l for painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and directed. 85 s & f for wall mounted led tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouputboxtype fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired andnecessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. 86 supply and fixing led luminaire 600 mm x 600 mm, 35/36 watt, 220 v ac recessed type with high efficiency pmma diffuser soft glare free light complete with driver, holders & led lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. 87 s & f led street light fitting 35 watt 230 v ac outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with ip 65/66 protection complete necessary mounting arrangements and provision of 0.75 sqmm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia gi pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by engineer in charge. 88 s & f exhaust fan, steel body ac single phase 230v of size 300mm sweep with, blades, and frame and louvers with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of pvc flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection complete all as specified and directed. 89 m & l for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to gi earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, pcc chamber, ci frame and cover, ms funnel with wire mesh all as shown in electrical plate no 3 of ssr part i including excavation and earthwork in any type ofsoil/strata and testing on completion. note: gi earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted. ...