46254845
tender for construction of prefabricated pre engineered building at roof top of ipd b block b side, department of anaesthesiology at aiims patna.; 1 reinforced cement concretereinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 2 centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers 3 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.thermo mechanically treated bars of grade fe 500d or more. 4 cladding work providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 5 wood and p. v. c. workproviding wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). sal wood 6 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including isi marked stainless steel butt hinges with necessary screws 7 providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with isi, is : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. 8 providing and fixing aluminium sliding door bolts, isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :300x16 mm 9 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm 10 providing and fixing aluminium handles, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm 11 providing and fixing aluminium hanging floor door stopper, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.twin rubber stopper 12 providing and fixing factory made upvc glazed/ wire mesh windows/ doors comprising of lead free upvc multi chambered frame, sash and mullion/ coupler (wherever required) extruded profiles having minimum wall thickness of 1.70 mm for series r1 and r2 profiles and 2.10 mm for series r3 and r4 profiles conforming to en: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per cpwd specification, upvc extruded glazing beads, interlocks and inline sash adaptor (whereever required) of appropriate dimension, epdm gasket, hardware, ss 304 grade fasteners of minimum 8 mm dia. with countersunk head, comprising of matching polyamide pa6 grade sleeve for fixing frame to finished wall as per is 1367: part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. after fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to cpwd specification & direction of engineer in charge. section of steel reinforcement and cross sections of upvc profiles to be as per design approved by engineer in charge. wire mesh/ glazing of plain/toughened/ laminated/ double glass unit with/without high performance coatings as per design requirements and conforming to is: 3548 & is: 16231 shall be paid separately. note: structural design proof checked from a government engineering institute, to be provided by the manufacturer for: (iii) sites with basic wind speed > 45 m/sec as per is 875 part 3 (iv) sites with structure height more than 20m for all wind speeds.three track three panels sliding window with aluminium channel for roller track, wool pile, nylon rollers with ss 304 body.using r4 series with frame (115mm & above) x (45mm & above) & sash (44mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on two end panels along with multi point locking system. (height above 1.8 meter). 13 steel workstructural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 14 flooring providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to is : 15622, of approved make, in all colours, shades, except white, ivory, grey, fume red brown, laid on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete. 15 providing and laying vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to i.s. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.size of tile 600x600 mm 16 roofingproviding and fixing thermal insulation with resin bonded fibre glass wool conforming to is: 8183. density 16 kg/m³, 50 mm thick, wrapped in 200g virgin polythene bags placed over existing false ceiling and held in position by criss crossing gi wire. 17 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes. 110 mm diameter 18 providing and fixing on wall face unplasticised pvc moulded fittings/ accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion.bend 87.5°110 mm bend 19 providing and fixing on wall face unplasticised pvc moulded fittings/ accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion.shoe (plain) 110 mm shoe 20 providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling/ self tapping screws cmplete: ridges plain (500 600mm) 21 providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling/ self tapping screws cmplete: flashings/ aprons.( upto 600 mm) 22 providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling/ self tapping screws cmplete: gutter (600 mm over all girth) 23 providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main t runner with suitably spacedjoints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross t of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main t at 600 mm center to center to form a grid of 1200x600 mm and secondary cross t of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. main t runners to be suspended from ceiling using gi slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm gi adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main t, bottom exposed width of 24 mm of all t sections shall be pre painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by engineer in charge. gi metal ceiling lay in perforated tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of gi sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having nrc (noise reduction coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black glass fiber acoustical fleece. 24 finishing finishing walls with acrylic smooth exterior paint of required shade :new work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 25 finishing with deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers specifications : two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm 26 dismantling and demolishingdemolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer in charge. nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) 27 dismantling g.i. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of engineer in charge :above 40 mm nominal bore 28 providing and fixing g.i. pipes complete with g.i. fittings and clamps including cutting and making good the walls etc. internal work exposed on wall40 mm dia nominal bore 29 providing and fixing g.i. pipes complete with g.i. fittings and clamps including cutting and making good the walls etc. internal work exposed on wall 50 mm dia nominal bore 30 making connection of g.i. distribution branch with g.i. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :25 to 40 mm nominal bore 31 providing and fixing gun metal gate valve with c.i. wheel of approved quality (screwed end) : 40 mm nominal bore 32 providing and fixing g.i. union in g.i. pipe including cutting and threading the pipe and making long screws etc. complete (new work):40 mm nominal bore 33 providing and fixing g.i. union in g.i. pipe including cutting and threading the pipe and making long screws etc. complete (new work): 50mm nominal bore 34 providing and fixing glazing in aluminium door, window , ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . (cost of aluminium snap beading shall be paidin basic item):with float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) 35 water proofingproviding and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.(b) laying second layer of fibre glass cloth when the first layer is still green. overlaps of joints of fibre cloth should not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. this will be allowed to air cure for 4 hours followed by water curing for 48 hours. the entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately .for the purpose of measurement the entire treated surface will be measured. 36 new technologies and materialsdesigning, providing, installing and fixing factory finished custom designed cold form light gauge steel framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. the steel sheet shall be galvanized (az 150gms aluminium zinc alloy coated steel having minimum yield strength 300 550 mpa) conforming to aisi specifications and ibc 2009 for cold formed steel framing and construction and also as per is: 875 1987, iso 800 1984 and is:801 1975. the wind load shall be as per provisions of is 875 (part iii). lgsfs frame shall be designed as per is: 801 using commercially available software such as frame cad pro 11.7/ staad pro v8i/ architekv2.5.16/ revit architecture 2011 or equivalent.proper usage of connection accessories like heavy duty tension ties, light duty hold ons, twist straps (to connect truss with wall frames), strong tie, tie rod, h brackets, boxing sections, l shaped angles for better structural stability. the framing section shall be cold form c type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple/ slot at required locations as per approved drawings. the slots will be along centre line of webs and shall be spaced minimum 250mm away from both ends of the member. the frame can besupplied in panelized or knock down condition in specific dimensions and fastened with screws extending through the steel beyond by minimum of three exposed threads. all self drilling tapping screws for joining the members shall have a type ii coating in accordance with astm b633(13) or equivalent corrosion protection of gauge 10 & 12, tpi 16 & 8 of length 20mm. the frames shall be fixed to rcc slab or tie beam over neoprene rubber using self expanding carbon steel anchor bolt of dia as per approved drawings. design subject to minimum 12mm diameter and 121mm length conforming to aisi 304 and 316 at 500mm c/c with minimum embedment of 100mm in rcc (rcc to be paid separately) and located not more than 300mm from corners or termination of bottom tracks complete in all respects. the item also includes the submission of stability reports duly examined and issued by any nit/iit. the rate includes the concept design, detailed design, fabrication of sections, transportation, installation and all required fixingarrangement at site as described above. 37 providing and fixing of external wall system on light gauge steel frame work with outer face cement boards as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c/c of approved make. a groove of 2 mm to 3mmshallbe maintained andgrooves shallbe sealed withsilicon based sealant. the board shall be fixed in a staggered pattern. screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm and. internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c/c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately)outer face outer face having 6mm thick fiber cement board type a,category ivasper is:14862:2000fixedon9mmthick fiber cement board, type a, category iv as per is:14862:2000 (high pressure steam cured)inner face 12.5 mm thick gypsum plaster boardconformingtois2095:2011fixedon 8mmthickfibre cementboardoftypeb,category iiiconformingto is:14862:2000 (high pressure steam cured) 38 providing and fixing internal wall panels on light gauge steel frame work with 12.5mm thick gypsum plaster board conforming is 2095:2011 fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c/c of approved make, screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. proper taping and jointing to be done using fiber mesh tape andepoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separatelycement fiber board 8 mm thick oftype b, category iii as per is 14862:2000 (high pressure steam cured) 39 supply , fittings and fixing of roller blinds with pully mechanism system with black out rich fabric etc all completed as per direction of engineer in charge 40 providing and fixing prefab roof made up of sandwich panel of 100mm thick of expended polystrene eps in pills having one sides precoated galvanised steel sheet of 0.5 mm thickon side flat and other side corrugated profiled roof with heat resistance etc all complete job 41 wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm frls pvc insulated copper conductor single core cable in surface i recessed steel conduit, with modular switch, modular plate, suitable gl box and earthing the point with 1.5 sq. mm frls pvc insulated copper conductor single core cable etc. as required.group a 42 wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed steel conduit as required 2 x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire 43 wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed steel conduit as required2 x 4 sq. mm + 1 x 4 sq. mm earth wire 44 wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed steel conduit as required 2 x 6 sq. mm + 1 x 6 sq. mm earth wire 45 wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed steel conduit as required 4 x 16 sq. mm + 2 x 6 sq. mm earth wire 46 supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 a switch 47 supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 a switch 48 supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 a socket outlet 49 supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 a socket outlet 50 supplying and fixing following size/ modules, gl box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 module (100mmx75mm) 51 supplying and fixing following size/ modules, gl box alongwith modular base & cover plate for modular switches in recess etc. as required.6 module (200mmx75mm) 52 supplying and fixing following size/ modules, gl box alongwith modular base & cover plate for modular switches in recess etc. as required.8 module (200mmx75mm) 53 installation,testingandcommissioningofceilingfan,including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mmfrlspvcinsulated,copperconductor,singlecorecable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. 54 installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. upto 450 mm sweep 55 supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, tpn mcb distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting mcb’s (but without mcb’s and incomer ) as required .(note : vertical type mcb tpdb is normally used where 3 phase outlets are required.) 8 way (4 + 24), double door 56 supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 ka, “c” curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. single pole 57 supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 ka, “c” curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required.single pole and neutral 58 supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 ka, “c” curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. triple pole and neutral 59 supplying and fixing 20 amps, 240 volts, spn industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps “c” curve, sp, mcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing andmmissioning etc. as required. 60 supplying, installation, testing & commisioning of following capacity plug in/ tap off box on the existing air insulated compact type bus trunking/ rising mains for use on 3 phase 4 wire 415 v, 50hz a.c. supply made with 1.6mm thick sheet steel enclosure (ip54) duly powder coated with provision of mccb (but without mccb) complete etc. as required125 a, lsc= 15ka for 1 sec (make: c&s) 61 providing and fixing 6 swg dia gi. wire on surface or in recess for loop earthing as required. 62 laying and fixing of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size on wall surface as required.above 35 sq. mm and upto 95 sq. mm(clamped with 25x3mm ms flat clamp 63 supplying and making end termination with brass compression gland and aluminium lugs for following size of pvc insulated and pvc sheathed / xlpe aluminium conductor cable of 1.1 kv grade as required. 3½ x 70 sq. mm (38mm) 64 supply, installation, testing and commissioning of 1200 mm sweep, bee 5 star rated, ceiling fan with brush less direct current (bldc) motor, class of insulation: b, 3 nos.blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, power factor not less than 0.9, service value (cmm/w) minimum 6.85, air delivery minimum 215 cmm, 350 rpm (tolerance as per is : 374 2019), thd less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree c (max.), insulation resistance more than2 mega ohm, suitable for 230 v, 50 hz, single phase ac supply, earthing etc. complete as required. 65 supplying & fixing 3.5 c x 70 sq. mm alarmoured cable xlpe 66 sitc of 15/18 w led down light cool day1x1 ftmake:syska,havells,philips. 67 sitc of 36/40 w led down light cool day2x2 ftmake:syska,havells,philips. 68 sitc of 300 mm exhaust fan 69 supply and fixing of 25 mm pvc casing bit 70 supply and fixing of 125 amp. 4 p 25 ka mccb at & fmmake: havells,l&t 71 metallic enclosure with spreader link suitable for above mentioned mccb 72 2 ton , bee 5 star invertersplit ac 73 providing and fixing copper line with insulation suitable for 2 tr split ac units (suctipon and discharge taken in one unit)dia of pipe: 5/8 &1/4 74 supplying and fixing drain pipe as per suitable for 2 tr split ac unit. 75 standard outdoor stand suitable for outdoor units for 2 tr split ac unit. 76 3 core 4 sq mm pvc insulated copper wire. 77 installation of ac 78 98 inch ultra hd interactive flat panel display with inbuilt android 11 os ,google pay store , 8 gb ram & 64 gb storage with two inbuilt speakers of 25 watt each along with subwoofer , multiple connectivity option like , 3 nos. of hdmi in vga in , audio in and out , 4 nos. of usb 3.0 rj45, inbuit dual band wi fi (2.4 & 5 ghz.)with hotspot and bluetooth 5.0 , interactive teachinng software , 4 mm tempered glass with anti glare coating and more with wall mount kit. ...
Due Date : December 09, 2024
Tender Value : ₹ 74.22 Lakhs
